Jonsered RS52の取扱説明書

36ページ 1.73 mb
ダウンロード

ページに移動 of 36

Summary
  • Jonsered RS52 - page 1

    GR41 GR50 RS44 RS52 Oper ator’ s manual (EP A) Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . ...

  • Jonsered RS52 - page 2

    2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or f atal injur y to the operator or others. It is e xtremely impor tant that you read and understand the contents of the operator’ s manual. Please read the oper ator’ s manual carefully and ...

  • Jonsered RS52 - page 3

    English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Please read the oper ator’ s manual carefully . Maintenance, replacement, or repair of the emission control de vices and system may be perf ormed by any nonroad engine repair establishment or individual. This label cer tify that the product has been cer tified in accordance w ...

  • Jonsered RS52 - page 4

    4 – English INTR ODUCTION Dear customer! Cong ratulations on y our choice to buy a Jonsered product! Y our purchase gives y ou access to prof essional help with repairs and ser vice whene ver this ma y be necessar y . If the retailer wh o sells your machine is not one of our authorized dealers , ask for the address of y our nearest ser vicing dea ...

  • Jonsered RS52 - page 5

    English – 5 WHA T IS WHA T? What is what on the c learing saw? (RS44) 23 24 1 Blade 2 Grease filler cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop s witch 9 Throttle lock out 10 Suppor t ey es f or har ness 11 Cylinder cov er 12 Star ter handle 13 Fuel tank 14 Choke control 15 Handle adju ...

  • Jonsered RS52 - page 6

    6 – English WHA T IS WHA T? What is what on the c learing saw? (RS52) 1 Blade 2 Grease filler cap , bev el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop s witch 9 Throttle lock out 10 Suppor t ey es f or har ness 11 Cylinder cov er 12 Star ter handle 13 Choke control 14 Air filter 15 Fuel tank 16 So ...

  • Jonsered RS52 - page 7

    English – 7 GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PRO TECTION W ear hear ing protection that pro vides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed eye protection. If you use a visor then you m ust also wear ...

  • Jonsered RS52 - page 8

    8 – English GENERAL SAFETY PRECA UTIONS Mac hine ′′ ′ ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose , and how checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine ...

  • Jonsered RS52 - page 9

    English – 9 GENERAL SAFETY PRECA UTIONS Cutting attac hment guard This guard is intended to pre vent loose objects from being thrown to wards the operator . The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cr acked. Replace the guard if it has been e xposed to impa ...

  • Jonsered RS52 - page 10

    10 – English GENERAL SAFETY PRECA UTIONS F or mufflers it is very impor tant that you f ollow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and ser vicing the machine’ s safety equipment. Ne ver use a machine that has a f aulty muffler . Regularly check that the ...

  • Jonsered RS52 - page 11

    English – 11 GENERAL SAFETY PRECA UTIONS Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting perf or mance . • Extend the lif e of cutting equipment. Cutting equipment Saw b lades are intended for cutting fibrous types of w ood. ...

  • Jonsered RS52 - page 12

    12 – English GENERAL SAFETY PRECA UTIONS Sharpening grass cutter s and grass blades • See the cutting attachment packaging f or correct shar pening instructions. Shar pen b lades and cutters using a single-cut flat file. • Shar pen all edges equally to maintain the balance of the blade . Sharpening the sa w blade • See the cutting attachm ...

  • Jonsered RS52 - page 13

    English – 13 ASSEMBL Y Assembling the handlebar and thr ottle • Unscrew the knob from the handlebar mounting. • P osition the handlebar as shown. Fit the mounting components and tighten the knob lightly . • Fit the right handle to the handlebar using the screw , washer , sleev e and nut as shown. Tighten. • Put on the harness and hang the ...

  • Jonsered RS52 - page 14

    14 – English ASSEMBL Y • Fit the suppor t flange (F) on the output shaft. Make sure that the blade is centered b y fitting it to the guide on the suppor t flange. • Screw the support cup (E) onto the output shaft threads (CA UTION! Left-hand thread). Tighten to a torque of 35- 50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool kit. No ...

  • Jonsered RS52 - page 15

    English – 15 ASSEMBL Y • Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm). • T o dismantle, follo w the instructions in the rev erse order . Fitting other guar ds and cutting attachments Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Secure the trimmer guard using the 4 screws (L ...

  • Jonsered RS52 - page 16

    16 – English ASSEMBL Y V ector harness Safety release Push down the red release le ver to release the machine from the harness. Adjusting the harness 1 Tighten the hip strap so that it sits securely . 2 Tighten the chest strap under y our left ar m so that it fits closely around your body . 3 Adjust the shoulder strap to distribute the load e ve ...

  • Jonsered RS52 - page 17

    English – 17 FUEL HANDLING Fuel safety Ne ver star t the machine: 1 If you ha ve spilled fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate . 2 If you ha ve spilled fuel on y ourself or your clothes , change your clothes . W ash any par t of your body that has come in contact with fuel. Use soap and water . 3 If the machine ...

  • Jonsered RS52 - page 18

    18 – English FUEL HANDLING Mixing • Alwa ys mix the gasoline and oil in a clean container intended f or fuel. • Alwa ys star t by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the fuel mixture thoroughly bef ore filli ...

  • Jonsered RS52 - page 19

    English – 19 ST AR TING AND ST OPPING Chec k before starting • Check the b lade to ensure that no cracks ha ve f or med at the bottom of the teeth or by the centre hole . The most common reason wh y cracks are f ormed is that shar p corners have been f or med at the bottom of the teeth while shar pening or that the b lade has been used with dul ...

  • Jonsered RS52 - page 20

    20 – English ST AR TING AND ST OPPING Starting Hold the body of the machine on the ground using y our left hand (CA UTION! Not with your foot!). Grip the star ter handle, slowly pull out the cord with y our right hand until you feel some resistance (the star ter pawls g rip), now quickly and powerfully pull the cord. Never wrap the starter cord a ...

  • Jonsered RS52 - page 21

    English – 21 W ORKING TECHNIQ UES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out b y the cutting a ...

  • Jonsered RS52 - page 22

    22 – English W ORKING TECHNIQ UES W orking methods • Bef ore you star t clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollo ws etc. • Star t at whiche ver end of the area is easiest, and clear an open space from which to work. • W or k systematically to and fro across the area, cl ...

  • Jonsered RS52 - page 23

    English – 23 W ORKING TECHNIQ UES • T o fell a tree f orwards, the bottom of the tree should be pulled backw ards. Pull the blade bac kwards with a quick, firm movement. • Large stems must be cut from two sides . First deter mine which direction the stem will f all. Make the first cut on the f elling side. Then finish cutting the stem from ...

  • Jonsered RS52 - page 24

    24 – English W ORKING TECHNIQ UES Grass trimming with a trimmer head T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Nev er press the cord into the area to be cut. • The cord can easily remov e grass and weeds up against walls , fences , tre ...

  • Jonsered RS52 - page 25

    English – 25 MAINTENANCE Carb uretor Y our Jonsered product has been designed and manuf actured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. T o ensure that the engine runs at peak performance and produces as little harmful exhaust fumes as possible after the running-in per ...

  • Jonsered RS52 - page 26

    26 – English MAINTENANCE Low speed jet L T r y to find the highest idling speed, tur ning the lo w speed needle L clockwise respectiv ely counter-clockwise . When the highest speed has been f ound, tur n the low speed needle L 1/ 4 turn counter-clockwise. Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T ...

  • Jonsered RS52 - page 27

    English – 27 MAINTENANCE Correctly adjusted carb uretor When the carburetor is correctly adjusted the machine will accelerate without hesitation and b urble a little at maximum speed. It is also impor tant that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it ma y cause star ting difficulties and poor acc ...

  • Jonsered RS52 - page 28

    28 – English MAINTENANCE Bevel gear The be vel gear is filled with the right amount of grease at the f actor y . How ev er , bef ore using the machine you should check that the be vel gear is filled 3/4 full with grease . Use JONSERED special grease. The grease in the be vel gear does not normally need to be changed e xcept if repairs are carr ...

  • Jonsered RS52 - page 29

    English – 29 MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine . Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and service work descr ibed in this manual. More e xtensive work must be carried out by an authorised ser vic ...

  • Jonsered RS52 - page 30

    30 – English TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le vel is calculated as the time-weighted energy total f or noise pressure le vels under v arious working conditions with the follo wing time distribution: 1/2 idle and 1/2 max. speed. NO TE! Noise pressure at the user’ s ear and vibration on the handles are measur ...

  • Jonsered RS52 - page 31

    English – 31 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to e xplain the emissions control system warranty on y our 2001 and later small nonroad engine. In U .S. and Canada, new small nonroad engines must be d ...

  • Jonsered RS52 - page 32

    1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII ...

  • Jonsered RS52 - page 33

    ...

  • Jonsered RS52 - page 34

    ´®z+R:•¶5Q¨ ´®z+R:•¶5Q¨ 2,7-3,3 mm .106-.130" 15 cm 6" 15 cm 6" 15 cm 6" 15 cm 6" 1 2 3 5 6 7 10 11 1.) 2.) >1,1 Kw <1,1 Kw 2,7 mm - 9,0 m 3,0 mm - 7,5 m 3,3 mm - 6,0 m 4 8 Auto 55 ...

  • Jonsered RS52 - page 35

    ...

  • Jonsered RS52 - page 36

    ´®z+R:•¶5Q¨ 2006-08-23 ´®z+R:•¶5Q¨ 1150269-95 ...

メーカー Jonsered カテゴリー Brush Cutter

Jonsered RS52のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RS52の取扱説明書
- Jonseredの製品カード
- パンフレット
- またはJonsered RS52の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Jonsered RS52の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Jonsered RS52の取り付け説明書、サービスマニュアル、簡易説明書、またはJonsered RS52のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Jonsered RS52の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Jonsered RS52デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJonsered RS52を使用するのを助ける技術的文書のことです。説明書は通常、全てのJonsered RS52ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Jonseredの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Jonsered RS52の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJonsered RS52の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Jonsered RS52に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Jonsered RS52デバイスの基本機能を使うにあたってのヒント。 Jonsered RS52のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Jonsered RS52に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJonsered RS52のメーカー/サービスへの連絡先に関する情報。

Jonsered RS52についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJonsered RS52の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJonsered RS52で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)