Electrolux G-11602, G-21602の取扱説明書

26ページ 0.39 mb
ダウンロード

ページに移動 of 26

Summary
  • Electrolux G-11602, G-21602 - page 1

    Gaskookplaat T able de cuisson Gas hob 20604 G - 21604 G 1 1602 G - 21602 G Gebruiksaanwijzing en Installatievoorschrift Notice dutilisation et dencastrement Operating and Installation Instructions NL FR GB ...

  • Electrolux G-11602, G-21602 - page 2

    36 ENGLISH GB Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation l This hob must be installed by qualified personnel, according to the manufacturer  s instructions and to the relevant British Standards. l ...

  • Electrolux G-11602, G-21602 - page 3

    37 l When in use a gas cooking hob will produce heat and moisture in the room in which it has been installed. Ensure there is a continuous air supply , keeping air vents in good condition or installing a cooker hood with a venting hose. l When using the hob for a long period time, the ventilation should be improved, by opening a window or increasin ...

  • Electrolux G-11602, G-21602 - page 4

    38 Contents Important Safety Information ......................................................................................... 3 6 Instructions for the User ................................................................................................ 3 9 Description of the Hobs ................................................................ ...

  • Electrolux G-11602, G-21602 - page 5

    39 1. Hob T o p 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) 9. Electric Ignition Push Button Description of the Hobs INSTALLATION Any gas ...

  • Electrolux G-11602, G-21602 - page 6

    40 HOB BURNERS T o light a burner , turn the relevant control knob anticlockwise to the maximum position. At the same time push the electric ignition button which is marked with a little spark. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installat ...

  • Electrolux G-11602, G-21602 - page 7

    41 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing u ...

  • Electrolux G-11602, G-21602 - page 8

    42 Something Not Working? If the hob is not working correctly , please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM n There is no spark when lighting the gas n The gas ring burns unevenly SOLUTION u Check that the unit is plugged in and the electrical supply is switched on u Check that the RCCB has n ...

  • Electrolux G-11602, G-21602 - page 9

    43 Service and Spare Parts When you contact the Service Centre, they will need the following information: 1. Y our name, address and post code. 2. Y our telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5. Date of purchase If you require spare par ...

  • Electrolux G-11602, G-21602 - page 10

    44 Guarantee Conditions Standard guarantee conditions W e, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour , materials or carriage on ...

  • Electrolux G-11602, G-21602 - page 11

    45 OVERALL DIMENSIONS Width: 580 mm. Depth: 500 mm. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 23 0-240V 50Hz supply , 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. IGNITION HT SPARK Spark Generator Ispra Control's BF ...

  • Electrolux G-11602, G-21602 - page 12

    46 BURNER RAPID SEMI-RAPID AUXILIARY (large) (m e d iu m ) (small) POSITION M A X M I N M A X M I N M A X M I N NOMINAL THERMAL POWER kW 3. 0 0.65 2.0 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 /h 0.286 0.057 0.190 0.038 0.095 0.028 NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust. 1/100 mm NOMINAL THERMAL POWER kW 2. 8 0.65 2.0 0.45 1.0 0.33 NOMINAL FLO ...

  • Electrolux G-11602, G-21602 - page 13

    47 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par . 2 and B.S. 6891 Current Editions ...

  • Electrolux G-11602, G-21602 - page 14

    48 CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer . The m ...

  • Electrolux G-11602, G-21602 - page 15

    49 A) End of shaft with nut B) W asher C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the G 1/2" threaded elbow , adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. It is important to install the elbow correctly , with the sh ...

  • Electrolux G-11602, G-21602 - page 16

    50 550 470 580 500 FO 2109 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out ...

  • Electrolux G-11602, G-21602 - page 17

    51 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under ...

  • Electrolux G-11602, G-21602 - page 18

    52 Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below . 1) Place the sealing gasket all around the edge of the cut out. 2) ...

  • Electrolux G-11602, G-21602 - page 19

    53 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240 ...

  • Electrolux G-11602, G-21602 - page 20

    54 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break t ...

  • Electrolux G-11602, G-21602 - page 21

    55 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check. Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation che ...

  • Electrolux G-11602, G-21602 - page 22

    56 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary .  T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight. B. INSULATION CHECK Applianc ...

  • Electrolux G-11602, G-21602 - page 23

    57 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check continuity fro ...

  • Electrolux G-11602, G-21602 - page 24

    58 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below. 1) T urn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguish ...

  • Electrolux G-11602, G-21602 - page 25

    59 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'OFF' position 2) Isolate the hob from the el ...

  • Electrolux G-11602, G-21602 - page 26

    35678-5902 02/03 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www .aeg.hausgeraete.de © Electrolux plc 2003 Grafiche MDM - Forlì F ro m t h e E lectrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrol ...

メーカー Electrolux カテゴリー Cooktop

Electrolux G-11602, G-21602のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G-11602, G-21602の取扱説明書
- Electroluxの製品カード
- パンフレット
- またはElectrolux G-11602, G-21602の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Electrolux G-11602, G-21602の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Electrolux G-11602, G-21602の取り付け説明書、サービスマニュアル、簡易説明書、またはElectrolux G-11602, G-21602のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Electrolux G-11602, G-21602の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Electrolux G-11602, G-21602デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがElectrolux G-11602, G-21602を使用するのを助ける技術的文書のことです。説明書は通常、全てのElectrolux G-11602, G-21602ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Electroluxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Electrolux G-11602, G-21602の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははElectrolux G-11602, G-21602の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Electrolux G-11602, G-21602に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Electrolux G-11602, G-21602デバイスの基本機能を使うにあたってのヒント。 Electrolux G-11602, G-21602のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Electrolux G-11602, G-21602に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるElectrolux G-11602, G-21602のメーカー/サービスへの連絡先に関する情報。

Electrolux G-11602, G-21602についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもElectrolux G-11602, G-21602の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがElectrolux G-11602, G-21602で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)