-
Anton/Bauer UL-2 - page 1
ULTRALIGHT 2 ( UL-2 ) OWNER’S MANUAL ...
-
Anton/Bauer UL-2 - page 2
...
-
Anton/Bauer UL-2 - page 3
TO REMOVE / REPLACE BULB NOTE: Only MR-16 type bulbs sho uld be used with the UL2. 1. Pull out on the Thumb Tabs of the Head M odule. 2. Swing Hood open. 3. Remove and replace bulb as necessar y. 4. Close Head Module, insuring that it “clicks ” closed. Thumb Tabs Hood TO RE-ATTACH HEAD MODULE Push Head M odule on to base, a s shown, u ntil the ...
-
Anton/Bauer UL-2 - page 4
INTRODUCTION The Ultraligh t 2 (UL2) is a n extremel y compact, sup er lightwe ight version of the orig inal Ultra light system, designed specific ally for o n-camer a lighting applicatio ns. The Ultra light 2 inco rporate s many uniq ue feature s includi ng: • Included with a AB-60, wide angle bulb. • A diffused glass for smoother beam pattern ...
-
Anton/Bauer UL-2 - page 5
5/64 Hex Wrench Shoe Sleeve Shoe Mount Thumbwheel Set Screw Be sure the Shoe Sleeve is completely inside the light, otherwise the light may swing back & forth. ¼-20 STUD MOUNT APPLICATION The Ultralight 2 is shipped standard with ¼ -20 Stud Mount for attachi ng to the camera handle. To remove/install a ¼-20 Stud Mount, f ollow these instruct ...
-
Anton/Bauer UL-2 - page 6
Stud Mount Application 1/4-20 Screw ACCESSORIES UL2 WEDGE The UL2 Wedge is developed specifically for use with the Anton/Bauer Ultralight 2 on-ca mera light. The UL2 Wedge provides the Ultralight 2 with an additional 20º of down angle lighting for shooting extreme close up camera shots (less than 3 feet). A Universal mounting design allows quick a ...
-
Anton/Bauer UL-2 - page 7
When properly fitted, the slot in the tab will align with a screw in the center of the hood. The ta b insertion requires a slight force. If the filter assembly is too loose and does not stay in place, bend each side of the tab in opposite dire ctions as show n to provide sufficient holdi ng friction. T h e friction on the filter pivot may be increa ...
-
Anton/Bauer UL-2 - page 8
UL-SOFT B OX The UL-Soft Box mounts easily to any Ultralight Head Module to sof ten and diffuse light output. The UL-Soft Box is collapsible allowing eas y storage or can fold and swing awa y while remaining on the Ultralight until needed. ULTRADAYLIGHT The UltraDaylight Head Module fits an y Ultralight base to instantly deliver 5600°k at less tha ...
-
Anton/Bauer UL-2 - page 9
BULB SELECTION AND OPERATION Bulbs used by the Ultralight 2 are T ype MR16, tungsten-halogen bul bs. Spot or flood bulbs of any light distribution angle may be used. The Ultralight 2 offers the greatest versatility with the following low voltage bulbs. The y can be powered from any 12-14.4 volt camera batter y with the Ultralight 2 in tegral PowerT ...
-
Anton/Bauer UL-2 - page 10
WARRANTY IMPORTANT: WARRANTY REGISTRAT ION CARD MUST BE MAILED WITHIN 10 DAYS OF PURCHASE TO QUALIFY FO R THIS WARRANTY. Pro per registration will also enabl e us to send you important update information. We must have the warrant y registration card on file at our CUSTOM ER SERVICE DEPARTMENT t o establish warranty. Proper registration will also en ...
-
Anton/Bauer UL-2 - page 11
...
-
Anton/Bauer UL-2 - page 12
The worldwide standard The following are registered trademarks of Anton/Bauer, Inc.: ACS, Anton/Bauer, Anton/Bauer Logo, Au tomatique, ComPac, Gol d Mount,HyTRON, Impac, InterActive, InterActive 2000 Logo, Lif eSaver, Logic Series,Logic S eries Logo, PowerStrap, ProPac, SSP, Satellight, Snap On,The worldwide standard, Triconn, TrimPac , Ultralight, ...
Anton/Bauer UL-2についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAnton/Bauer UL-2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAnton/Bauer UL-2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。