Snapper 2167519Bの取扱説明書

28ページ 1.44 mb
ダウンロード

ページに移動 of 28

Summary
  • Snapper 2167519B - page 1

    Safety Instructions & Operator's Manual for NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for further details. Manual No. 7101294 ...

  • Snapper 2167519B - page 2

    Thank Y ou for pur chasing this quality-built Snapper product. We’re pleased that you placed your confidence in the Snapper brand. When operated and maintained according to the instructions in this manual, your Snapper product will provide many years of dependable service. This manual contains safety information to make you aware of the hazards a ...

  • Snapper 2167519B - page 3

    1 Operator Safety Features and Controls Operation Maintenance T roubleshooting Warranties T able of Contents Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Features and Control ...

  • Snapper 2167519B - page 4

    www .snapper .com 2 Operator Safety ! ! Important Operator Safety Instructions WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The o ...

  • Snapper 2167519B - page 5

    3 Operator Safety ! ! Important Operator Safety Instructions (Continued) Safe Handling of Gasoline (Continued From Previous Page) 6. DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner . Always place the contain- ers on the ground away from the vehicle before filling. 7. Remove gas-powered equipment from t ...

  • Snapper 2167519B - page 6

    www .snapper .com 4 Features and Controls IMPORT ANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your Snapper dealer if you have questions. Features and Controls A. Oil Fill Cap and Dipstick B. Fuel Filler Cap C. Grass Bag Adapter D. Rear Height Adjustment Latch (2) E ...

  • Snapper 2167519B - page 7

    5 Operation Pre-Start Check List Make the following checks and perform the ser vice required before each start-up. 1. Check the guards, deflectors, grass bag, adapter , and covers to make sure all are in place and securely tightened. 2. Check the blade control (A, Figure 1) , wheel drive control (B) , and ground speed control (C) to insure they wor ...

  • Snapper 2167519B - page 8

    www .snapper .com 6 Operation Starting and Operation (Continued) Engine and Blade (Kawasaki Engine) 1. Make sure the fuel valve (A, Figure 5) on the engine is open. 2. Move the engine speed control past the fast (‘Rabbit’) detent to the ‘Choke’ position. 3. Pull the blade control (A, Figure 4) against the handle. 4. Pull the rope start hand ...

  • Snapper 2167519B - page 9

    7 Operation Cutting Height Adjustment 1. Pull the height adjusting latch (A, Figure 8) outward and move to the desired cutting height. 2. Set all wheels at the same cutting height. The highest cutting position is Notch 7 (Figure 9) . The lowest cutting position is Notch 1. Recycling Operation Note: For best recycling results, cut up to a maximum of ...

  • Snapper 2167519B - page 10

    www .snapper .com 8 Operation Installing the Discharge Deflector 1. Remove the recycling cover . Refer to the Section entitled “Recycling Operation”. 2. Install the deflector (A, Figure 11) to the deck in place of the recycling cover , making sure that: The front hole (B) on the outside front of the deflector fits over the stud where the front ...

  • Snapper 2167519B - page 11

    9 Operation Installing the Grass Bag Adapter (Continued) Flip the pulley over so that the bushing flange is under the pulley . The bushing will act as a washer between the pulley and the standoff. Reassemble the pulley to the bag adapter , and install the supplied replacement bolt, fitted with the thread sleeve, into the recoil cover . Tighten all ...

  • Snapper 2167519B - page 12

    www .snapper .com 10 Maintenance Maintenance - Introduction T o retain the quality of the mower , use genuine SNAPPER replacement parts only . Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower , always mention the model and serial number . Ser vice - After First 5 Hours Chang ...

  • Snapper 2167519B - page 13

    11 Maintenance Check Mower Blade 1. Disconnect the spark plug wire and secure the end away from the plug. 2. Tilt the mower up on its rear wheels for access to the blade cap screw (A, Figure 19) . Do not tilt the mower with the spark plug or carburetor down. Important: Drain the fuel tank before tipping the mower . DO NOT tip the machine with the c ...

  • Snapper 2167519B - page 14

    www .snapper .com 12 Maintenance Mower Blade Replacement Standard Blade Wear Limit 1. Inspect the blade (Figure 20) frequently for signs of excessive wear or damage: (A) New blade (B) Wear limit (notch starts) (C) Dangerous condition! Do not use on the mower! Replace with a new blade. Ninja Blade Wear Limit 1. Inspect the blade (Figure 21) frequent ...

  • Snapper 2167519B - page 15

    13 Maintenance Blade Sharpening (Continued) 4. Sharpen the blade on a grinding wheel at an angle of 22 to 28 degrees (B, Figure 23) . DO NOT sharpen the blade beyond the original cutting edge (A) . 5. Check blade for balance. If necessary , correct balance by grinding heavy end of blade. 6. Reinstall blade (B, Figure 22) . Note the correct assembly ...

  • Snapper 2167519B - page 16

    www .snapper .com 14 Maintenance Driven and Drive Disc Ser vice If the mower does not propel itself properly , check for the following problems: 1. Grease on the drive disc (A, Figure 25) causing slippage. 2. Broken or disconnected drive spring (B) . 3. Driven disc (C) is out of adjustment. 4. Driven disc rubber is worn - does not contact drive dis ...

  • Snapper 2167519B - page 17

    15 Maintenance Driven Disc Adjustment (Continued) 2. Remove the driven disc spring (A, Figure 28) from the driven disc assembly (B) . Also remove the pin and washer (C) from the transfer rod (D) , and remove the end of the transfer rod from the hole in the driven disc assembly . 3. Slide the driven disc assembly over to 1/8” (A, Figure 29) from t ...

  • Snapper 2167519B - page 18

    www .snapper .com 16 Maintenance Driven Disc Replacement (Continued) 2. Using needle nose pliers, unhook the drive spring (A, Figure 31) and slide the driven disc assembly off the hex shaft. 3. Remove the two snap rings (A, Figure 32) which secure the rubber driven disc (B) to the driven disc assembly . 4. Install a new rubber driven disc onto the ...

  • Snapper 2167519B - page 19

    17 Maintenance Replacing the Bearing On the Pulley End Of the Hex Shaft T o replace the bearing on the pulley end of the hex shaft, proceed as follows: 1. Hold the hex shaft with an adjustable wrench held next to the pulley . 2. Remove the 3/8” hex lock nut (B, Figure 33) , located on the outside of the right wheel bracket. 3. Remove the holder ( ...

  • Snapper 2167519B - page 20

    www .snapper .com 18 Maintenance Engine Drive Belt Replacement (Stretch T ype Belts - Continued) IMPORT ANT : Drain the fuel tank before tipping the mower . DO NOT tip the machine with the carburetor or spark plug down. Oil from the crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination ...

  • Snapper 2167519B - page 21

    19 Maintenance Batter y Service New Battery Preparation 1. Remove the battery from the carton. 2. Place the battery in a well ventilated area on a level non- concrete surface. 3. Remove the battery cell caps. Fill the cells as required with electrolyte (supplied with battery) to the proper level. Filling the battery with electrolyte will bring the ...

  • Snapper 2167519B - page 22

    www .snapper .com 20 Maintenance ITEM SERVICE PERFORMED REF . EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 5 X Initial Oil Change Page 10 X Periodic Oil Change Page 11 X* Air Pre-Cleaner Clean Sponge Element Engine Manual X** Air Cleaner Clean or Replace Engine Manual X** Spark Plug Replace Engine Manual X Engine ...

  • Snapper 2167519B - page 23

    21 T roubleshooting PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start Using Recoil Starter 1. Fuel tank empty . 1. Fill fuel tank with fresh fuel. 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for Instructions. 3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug. 4. Kawasaki Engines Only ...

  • Snapper 2167519B - page 24

    www .snapper .com 22 Warranties 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original pur chaser’ s residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, ...

  • Snapper 2167519B - page 25

    23 Notes ...

  • Snapper 2167519B - page 26

    www .snapper .com 24 Notes ...

  • Snapper 2167519B - page 27

    25 ...

  • Snapper 2167519B - page 28

    www .snapper .com Snapper Products 535 Macon Street McDonough, GA 30253 21” STEEL DECK W ALK MOWERS SERIES 19 1-800-935-2967 Engine Power Rating Information: The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & T orque Rating Procedure), an ...

メーカー Snapper カテゴリー Lawn Mower

Snapper 2167519Bのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2167519Bの取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper 2167519Bの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper 2167519Bの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper 2167519Bの取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper 2167519Bのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper 2167519Bの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper 2167519Bデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper 2167519Bを使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper 2167519Bユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper 2167519Bの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper 2167519Bの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper 2167519Bに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper 2167519Bデバイスの基本機能を使うにあたってのヒント。 Snapper 2167519Bのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper 2167519Bに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper 2167519Bのメーカー/サービスへの連絡先に関する情報。

Snapper 2167519Bについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper 2167519Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper 2167519Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)