-
Gianni Industries AD-425S - page 1
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 1/ 20 AD-425S Automatic Door Operator Instruction Manual General Safety Precautions z This instruction manual is intend ed sole ly for use by qualified professionals. All installation s, electrical connections and adjustments must follow the inst allation instructions. z ...
-
Gianni Industries AD-425S - page 2
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 2/ 20 z Make sure the volt age specified as correct for the device. z Must provide at least 10 seconds rest ti me between every restarting cycle to ensure adequate residual current can be return ed to power system. z Make sure to turn the power off before in st alling and ...
-
Gianni Industries AD-425S - page 3
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 3/ 20 All Packing materials 1. Construction Name ○ 1 C o v e r ○ 2 M o t o r ○ 3 Reducer ○ 4 Square Couplings ○ 5 Control Board ○ 6 Battery ○ 7 Power Switch ○ 8 Operating Arm ○ 9 Sliding Rail ○ 10 S topper Ball ○ 1 1 Baseplate ○ 12 T ransformer 2. ...
-
Gianni Industries AD-425S - page 4
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 4/ 20 3. Control Board Guide Input/Output Cont act Explanation Remark Make sure the input is use d corre ctly (AC1 10 or 220V). When turn on the power switch, it enters a learning mode. Power Switch AD-425S Operating Arm t urns clockwise. (See Fig ure 5~8 ) AD-425S Operat ...
-
Gianni Industries AD-425S - page 5
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 5/ 20 Input/Output Contact Explanation Remark Jumper 1-2 is N.C. cont act. N. C. (default) Jumper 1-3 is N.O. conta ct. N. O. (default) Jumper 1-8 is N.C., or using the “OPEN” switch. AD-425S becomes aut omatic mode. When the connector is N.O. or using the “HOL D” ...
-
Gianni Industries AD-425S - page 6
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 6/ 20 The opening, closing and maintain -open time illustration table. VM (Opening and Closing T im e Adjustment ) Opening and Closing Operating Ti m e Total Opening and Closing Time (VM+ Brake Time) TC Time (Maintain -o p en time adjustment) Maintain -open time (See Figu ...
-
Gianni Industries AD-425S - page 7
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 7/ 20 5. S pecification Power Input 1 10V (or 220V) AC ， 50-60H z Current (See Figure 2 ) 3.5A max., 0.6A average T orque 30Nm Opening/Closing time (VM) 4.5~9.5 s （ 90° ） Maintain - Op en time (TC) 1~35 seconds Battery S pecification 12V 1.2AH T emperature -20 ~+55 ...
-
Gianni Industries AD-425S - page 8
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 8/ 20 Installation instructi ons z Refer to figure 3 for in-swing door (ri ght -hand). Figure 3 z Opening, Closing action time and Maint ain time illustration. AD-425S will be automatically counted the round trip dist ance and can be adjusted the opening, closing and brea ...
-
Gianni Industries AD-425S - page 9
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 9/ 20 Figure 5 : For right-hand and out-swing door . F/R switch set 「 ON 」 . Operating Arm mount s to left-side. Figure 6 : For left-hand and out-swing d oor . F/R switch set 「 1 」 . Operating Arm mounts to right-side. Figure 7 : For right-hand and in-swing door . ...
-
Gianni Industries AD-425S - page 10
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 10/ 20 z Figure 1 1~13 showing a n operator in stallation of a minimum door leaf wid th and a maximum opening angle. The opening angle is recommend ed not excess to 120 ∘ . Figure 1 1 Figure 12 Figure 13 z Figure 14 : Automatic door operator dimension Figure 14 z Instal ...
-
Gianni Industries AD-425S - page 11
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2 008.07.1 1 Page: 1 1/ 20 AD-425S T emplate Installation Instruction Figure 17 Out-swing door (Right-Hand Open) Figure 18 Out-swing door (Left-Hand O pen) Figure 19 In-swing door (Right-Han d Open) Figure 20 In-swing door (Lef t-Hand Open) ...
-
Gianni Industries AD-425S - page 12
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 12/ 20 Inst allation Step s Out-swing door ( Right-Hand O pen ) S tep Figures Explanation S tep 1. Place the AD-425S template to the right position on the door header . See the figure presented for an out-swing door (Right-Hand Open), more det ails shown in Figure 17. S t ...
-
Gianni Industries AD-425S - page 13
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 13/ 20 S teps Figures Explanation S tep 7. Use Allen Wrench to tighten the Blind Nut. This will compress the sc rew so that it remains permanently fixed in the hole. Repeat these step s on other Blind Nuts. (Do not over tighten the Blind Nut.) Blind Nuts Inst allation ill ...
-
Gianni Industries AD-425S - page 14
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 14/ 20 S teps Figures Explanation S tep 12. Use Allen Wrench to tighten the Blind Nut. This will compress the sc rew so that it remains permanently fixed in the hole. Repeat these step s on other Blind Nuts. (Do not over tighten the Blind Nut.) S tep 13. Blind Nuts inst a ...
-
Gianni Industries AD-425S - page 15
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 15/ 20 S teps Figures Explanation S tep 18. T ighten screws. S tep 19. Insert screws (6 x 95 mm) to the Oper ating Arm on Square See the figure present e d for a out-swing door (Right-Hand Open), more det ails shown in Figure 9. S tep 20. T ighten nut at other end of scre ...
-
Gianni Industries AD-425S - page 16
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 16/ 20 S teps Figures Explanation S tep 24. Fix the Sliding Rail on the door leaf. (Screw specification: 6 X 20 mm) S tep 25. Slide in the Sliding Rail Cover . S tep 26. Attach two Side Ends. S tep 27. Depending on the door leaf opening angle, there may need a Stopper Bal ...
-
Gianni Industries AD-425S - page 17
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 17/ 20 S teps Figures Explanation S tep 30. First opening movement, the AD-425S will b e automatically set the opening angle and dist ance. S tep 31. Attach the cover . S tep 32. Attach the Operating Arm cap. Make final settings and adjustments Please refer to page 4~6 fo ...
-
Gianni Industries AD-425S - page 18
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 18/ 20 T rouble shooting Problem Possible Cause Solution No AC power Make sure the Control Board an d fuse are working properly and connected properl y . Motor have no power (LED motor light not on.) Make sure all motor terminals are connected properly . Jumper 1-9, or PU ...
-
Gianni Industries AD-425S - page 19
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 19/ 20 Problem Possible Cause Solution Safety devices are on Contact you r local distributor to check the Photocell and Safety Device. (ke ep the device clean) The door automatically open but doesn’t close. “REDA 1”, “REDA 2” contacts are on. Check the “REDA 1 ...
-
Gianni Industries AD-425S - page 20
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 20/ 20 General Safety Precautions The following precautions are e ssential for the user . z Read the precaution below carefully as it cont ains imp ortant information about safe inst allation and maintenance. z This instruction must be c ondu cted to a ll potential users. ...
Gianni Industries AD-425Sについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもGianni Industries AD-425Sの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGianni Industries AD-425Sで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。