Linksys WET54GS5の取扱説明書

69ページ 1.68 mb
ダウンロード

ページに移動 of 69

Summary
  • Linksys WET54GS5 - page 1

    A Division of Cisco Systems, Inc . ® Model No . Ether net Bridge Wir eless- G WET54GS5 User Guide WIRELESS GH z 2.4 802.11g with 5-Port Switch ...

  • Linksys WET54GS5 - page 2

    Wireless-G Ethernet Bridge with 5-P ort Switch Copyright and T rademarks Specifications are subject to change without notice . L inksys is a registered tradema rk or trademark of Cisco Systems, Inc . and/or its affiliates in the U.S . and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product na ...

  • Linksys WET54GS5 - page 3

    Wireless-G Ethernet Bridge with 5-P ort Switch Table of Contents Chapter 1: Introduction 1 Welcome 1 What’s in this Guide? 2 Chapter 2: Planning Your Wireless Network 4 Network Topology 4 Network Layout 5 Chapter 3: Getting to Know the Wireless-G Ethernet Bridge with 5-Port Switch 6 The Back Panel 6 The Front Panel 7 The Side Panel 9 Chapter 4: C ...

  • Linksys WET54GS5 - page 4

    Wireless-G Ethernet Bridge with 5-P ort Switch Security Precautions 47 Security Threats Facing Wireless Networks 47 Appendix C: Upgrading Firmware 50 Appendix D: Windows Help 51 Appendix E: Glossary 52 Appendix F: Specifications 59 Appendix G: Warranty Information 61 Appendix H: Regulatory Information 62 FCC Statement 62 Industry Canada (Canada) 62 ...

  • Linksys WET54GS5 - page 5

    Wireless-G Ethernet Bridge with 5-P ort Switch List of Figures Figure 2-1: Infrastructure Network 4 Figure 2-2: Ad-Hoc Network 5 Figure 2-3: Network Using Wireless Bridging 5 Figure 3-1: Back Panel 6 Figure 3-2: Front Panel 7 Figure 3-3: Side Panel 8 Figure 4-1: Connect to the Network 10 Figure 4-2: Connect the Power 11 Figure 5-1: Welcome 12 Figur ...

  • Linksys WET54GS5 - page 6

    Wireless-G Ethernet Bridge with 5-P ort Switch Figure 7-10: WPA RADIUS-TTLS 27 Figure 7-11: WPA Pre-Shared Key 28 Figure 7-12: Log Table 28 Figure 7-13: Password Tab 29 Figure 7-14: Wireless Tab 30 Figure 7-15: Spanning Tree Protocol Tab 31 Figure 7-16: QOS Tab 32 Figure 7-17: Switch Table Tab 33 Figure 7-18: VLAN Tab 34 Figure 7-19: RMON Statistic ...

  • Linksys WET54GS5 - page 7

    1 Chapter 1: Introductio n Welcome Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 1: Introduction We lc o me Thank you for choosing the Wireless-G Ethernet Bridge with 5- port Switch. The Wireless-G Ether net Bridge with 5-port Switch can make any wired Ether net-equipped device a part of your wireless 802.11b or 802.11g network. At home , ...

  • Linksys WET54GS5 - page 8

    2 Chapter 1: Introductio n What’s in this Guide? Wireless-G Ethernet Bridge with 5-P ort Switch What’ s in this Gu ide? This user guide covers the steps for setting up and using the Wireless-G Ethernet Bridge with 5-Port Switch. • Chapter 1: Introduction This chapter describes the Wireless-G Et hernet Bridge applications and this user guide. ...

  • Linksys WET54GS5 - page 9

    3 Chapter 1: Introductio n What’s in this Guide? Wireless-G Ethernet Bridge with 5-P ort Switch • Appendix E: Glossary This appendix gives a brief glossar y of terms frequently used in networking. • Appendix F: Specifications This appendix provides the technical specifications for the Bridge . • Appendix G: Warr anty Information This append ...

  • Linksys WET54GS5 - page 10

    4 Chapter 2: Planning Your Wireless Network Network Topology Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 2: Planning Y our Wireless Network Network T opology A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each computer in the WLAN uses a wireless device to connect to the network. Comp ...

  • Linksys WET54GS5 - page 11

    5 Chapter 2: Planning Your Wireless Network Network Layout Wireless-G Ethernet Bridge with 5-P ort Switch Network La yout The Wireless-G Ethernet Bridge is compatible with all 8 02.11b and 802.11g routers, such as model numbers BEFW11S4 and WRT54G, as well as access points, including model numbers WAP11 and W AP54G. The Bridge will also communicate ...

  • Linksys WET54GS5 - page 12

    6 Chapter 3: Getting to Know the Wireless-G Ethernet Bridge wi th 5-Port Switch The Back Panel Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 3: Getting to Know the Wireless-G Ethernet Bridge with 5-Por t Switch The Back P anel All network connections to the Bridge are made through the ports on its back panel, shown in Figure 3-1. The reset ...

  • Linksys WET54GS5 - page 13

    7 Chapter 3: Getting to Know the Wireless-G Ethernet Bridge wi th 5-Port Switch The Front Panel Wireless-G Ethernet Bridge with 5-P ort Switch The Front P anel The LEDs indicate network activity experienced by the Bridge . (See Figure 3-2.) Po w e r Green. The Power LED will light u p when the Bridge is powered on. While the Bridge is booting up an ...

  • Linksys WET54GS5 - page 14

    8 Chapter 3: Getting to Know the Wireless-G Ethernet Bridge wi th 5-Port Switch The Front Panel Wireless-G Ethernet Bridge with 5-P ort Switch Figure 3- 3: Side P anel NOTE: If you use a Power over Ethernet (PoE) device to supply data and power through the Ethernet network cable, then you do not need to use the Power port. ...

  • Linksys WET54GS5 - page 15

    9 Chapter 3: Getting to Know the Wireless-G Ethernet Bridge wi th 5-Port Switch The Side Panel Wireless-G Ethernet Bridge with 5-P ort Switch The Side P anel The Power port is on the side panel. (See Figure 3-3.) Po w e r The Power port is where you will connect the power adapter . ...

  • Linksys WET54GS5 - page 16

    10 Chapter 4: Connecting the Wireless-G Eth ernet Bridge for Setup Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 4: Connecting the Wireless-G Ethernet Bridge for Setup 1. Attach the Bridge’ s antenn a. 2. Plug the included Ethernet network cable into one of the five LAN ports on the back panel of the Bridge, shown in Figure 4-1. 3. Plug ...

  • Linksys WET54GS5 - page 17

    11 Chapter 4: Connecting the Wireless-G Eth ernet Bridge for Setup Wireless-G Ethernet Bridge with 5-P ort Switch 4. Plug the supplied power cable into the Power port on the side panel of the Bridge , shown in Figure 4-2. Then plug the other end into an electrical outlet. Proceed to “Chapter 5: Setting Up the Wireless-G Ethernet Bridge. ” Figur ...

  • Linksys WET54GS5 - page 18

    12 Chapter 5: Setting Up the Wireless-G Ethernet Bridge Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 5: Setting Up the Wireless-G Ethernet Bridge Now that you’ve connected the Wireless-G Ethernet Bridge to your wired network, you are ready to set it up . The Setup Wizard will guide you through all the necessar y steps. 1. Insert the Set ...

  • Linksys WET54GS5 - page 19

    13 Chapter 5: Setting Up the Wireless-G Ethernet Bridge Wireless-G Ethernet Bridge with 5-P ort Switch 4. The screen shown in Figure 5-3 displays a list of Wireless- G Ethernet Bridges on your network, along with the status information for each Bridge . (If you have only one Bridge on your netwo rk, it will be the only one displayed.) Select the Br ...

  • Linksys WET54GS5 - page 20

    14 Chapter 5: Setting Up the Wireless-G Ethernet Bridge Wireless-G Ethernet Bridge with 5-P ort Switch 6. The screen shown in Figure 5-5 shows a choice of two wireless modes. Click the Infrastructure radio button if you want your wireless computers to network with computers on your wired network using a wireless access point. Click the Ad-Hoc radio ...

  • Linksys WET54GS5 - page 21

    15 Chapter 5: Setting Up the Wireless-G Ethernet Bridge Wireless-G Ethernet Bridge with 5-P ort Switch 7. The Wireless Settings screen, shown in Figure 5-6, will now appear . Enter your wireless network’ s SSID . If you chose Ad-Hoc mode , select the channel at which the network broadcasts its wireless signal. If you have Wireless-G (802.11g) and ...

  • Linksys WET54GS5 - page 22

    16 Chapter 5: Setting Up the Wireless-G Ethernet Bridge Wireless-G Ethernet Bridge with 5-P ort Switch 9. The Security Settings (Optional) screen, shown in Figure 5-8, appears next. From the drop-down menu, select one of the wireless security mode options supported by the Bridge: WP A PSK (Pre-Shared Key) and WEP . (WP A stands for Wi-Fi Protected ...

  • Linksys WET54GS5 - page 23

    17 Chapter 5: Setting Up the Wireless-G Ethernet Bridge Wireless-G Ethernet Bridge with 5-P ort Switch 10. Review your settings on the Confirmation screen, shown in Figure 5-10. Write d own the Bridge’ s IP Address if you want to configure advanced settings throu gh the Bridge’ s Web-based Utility . Click the Ye s button to save these settings. ...

  • Linksys WET54GS5 - page 24

    18 Chapter 6: Connecting the Wireless-G Eth ernet Bridge for Network Use Connection to a Network Device Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 6: Connecting the Wireless-G Ethernet Bridge for Network Use Connection to a Network Device 1. After configuration, unplug the power cable from t he electrical outlet, and unplug the Ethernet ...

  • Linksys WET54GS5 - page 25

    19 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Overview Wireless-G Ethernet Bridge with 5-P ort Switch Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utilit y Overview The Bridge is designed to function properly after you configure it using the Setup Wizard. However , if you would like to change these basic settings ...

  • Linksys WET54GS5 - page 26

    20 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch Setup The Setup scre en, shown in Figure 7-2, lets you configure the wired and wireless network settings for the Bridge . When finished making your changes on this tab , click the Apply button to save these changes, or click the ...

  • Linksys WET54GS5 - page 27

    21 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch Wireless • SSID - The SSID is the network name shared among a ll devices in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 alphanumeric chara ...

  • Linksys WET54GS5 - page 28

    22 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch Wireless-B (802.11b) devices in your network. Select G-Only if you have only Wireless-G devices in your network. • Security - T o enable security , select Enable , then click Edit Security Settings . T o disable security , sel ...

  • Linksys WET54GS5 - page 29

    23 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch If your page doesn’t automatically refresh itself , then click the Refresh button of your web browser . Click the Apply button to save your changes and close the screen. RADIUS This option features WEP used in coordination wit ...

  • Linksys WET54GS5 - page 30

    24 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch • User ID and Password. A user identification and password are required for your security . Enter the ID in the User ID field, then the password in the Password field. When finished making your changes on this tab , click the ...

  • Linksys WET54GS5 - page 31

    25 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch TTLS TTLS is a mutual authentication method that uses digital certificates. Select TTLS from the EAP T ype drop- down menu. Enter the Login name of your wireless network in the User ID field and the password in the Password fiel ...

  • Linksys WET54GS5 - page 32

    26 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch WP A RADIUS WP A RADIUS. This option features WP A used in coordination with a RADIUS ser ver . (This should only be used when a RADIUS ser ver is connected to the Router .) The WP A algorithm used is TKIP . Enter the RADIUS ser ...

  • Linksys WET54GS5 - page 33

    27 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch TTLS TTLS is a mutual authentication method that uses digit al certificates. Select TTLS from the EAP T ype drop- down menu. Enter the Login name of your wireless network in the User ID field and the password in the Password fie ...

  • Linksys WET54GS5 - page 34

    28 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Setup Wireless-G Ethernet Bridge with 5-P ort Switch WP A Pre-Shar ed Key WP A g ives you TKIP for the encryption m ethod. Enter a WP A Shared Key of 8-32 characters. (See Figure 7-11.) Enter a key shared between the Bridge and the ser ver . Click the Apply button to save your cha ...

  • Linksys WET54GS5 - page 35

    29 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Password Wireless-G Ethernet Bridge with 5-P ort Switch Pa s s w o r d The Password screen, shown in Figure 7-13, lets you change the Bridge’ s User name and Password and restore the factory default setting s. • Username - It is strongly recommended that you cha nge the factor ...

  • Linksys WET54GS5 - page 36

    30 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch Wireless Use the Wireless screen, shown in Figure 7-14, to customize advanced wireless settings and clone a MAC address onto the Bridge. Advanced Wireless • T ransmission Rate - The default setting is Auto . The range is fr ...

  • Linksys WET54GS5 - page 37

    31 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch currently connected to the Bridge’ s LAN port. The Bridge will actively scan for a new MAC address to be cloned whenever you disconnect and re-connect multiple devices to the Bridge through its LAN port. Select Manual if yo ...

  • Linksys WET54GS5 - page 38

    32 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch Cost - The path cost to forward pack ets from this port, it's usually inversely proportional to the speed of the port. State - The STP state deter mined by the Spanning T ree protocol. They are Blocking , Listening, Lear ...

  • Linksys WET54GS5 - page 39

    33 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch • All Packets - This rate limit will be applied to all packets. • Flooded - This rate limit will be applie d to Flooded unicast and Multicast and Broadcast packets. • Multicast - This rate limit will be applied to M ult ...

  • Linksys WET54GS5 - page 40

    34 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch dynamic learned entries to force it to lear n again. It will only dump at most 64 entries per page . If there are already 64 entries, use Get Next Page to get more pages. • Life Remaining - This is the life remaining before ...

  • Linksys WET54GS5 - page 41

    35 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch The port1 to port6 checkbox is disabled so that the user can always use port1 as a back door to access the web config page when the port based VLAN is enabled. • 802.1q Port VLAN Setting - Default VID Is used when 802.1q is ...

  • Linksys WET54GS5 - page 42

    36 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch RMON Statistics This screen is used to view the RMON counters for each port. Port Selection - Select the port to display the packets statistics. EtherStatsDropEvents - The total number of events in w hich packets were dropped ...

  • Linksys WET54GS5 - page 43

    37 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Wireless-G Ethernet Bridge with 5-P ort Switch Octets (FCS Error) or a bad FCS w ith a non-integral number of octets (Alignment Error). Note that this defin ition of jabber is different than the definition in IEEE-802.3 sect ion 8.2.1.5 (10BASE5) and section 10.3.1.4 (10B ...

  • Linksys WET54GS5 - page 44

    38 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Port Mirroring Wireless-G Ethernet Bridge with 5-P ort Switch Po r t M i r r o r i n g This screen shows the status of each port and allows you to configure the port mirroring settings for the manage switch feature . The informa tion here is for the wired LAN ports. For wireless s ...

  • Linksys WET54GS5 - page 45

    39 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Access List Wireless-G Ethernet Bridge with 5-P ort Switch Access List This screen is used to configure the access list settings between wireless and switch ports. Access List T ype - An Access List is a list of source MAC addresses. If a packet is coming from a wireless to a LAN ...

  • Linksys WET54GS5 - page 46

    40 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless Status Wireless-G Ethernet Bridge with 5-P ort Switch Figure 7-22: Wir eless Sta tus T ab Wireless Status The Status screen displayed the Bridge’s current status and settings. All information is read-only . • Device Name - The name you have assigned to the Bridge is d ...

  • Linksys WET54GS5 - page 47

    41 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Wireless-G Ethernet Bridge with 5-P ort Switch Click the Refresh button to obtain the most up-to-date settings and statistics. Click the Help button for additional on-screen information. SNMP This screen is used to configure the SNMP T rap related setting s for the Bridge . SNMP T ...

  • Linksys WET54GS5 - page 48

    42 Chapter 7: Using the Wireless-G Ethernet Bridge Web-based Utility Help Wireless-G Ethernet Bridge with 5-P ort Switch Help The Help screen offers links to all of the help infor mation for the Web-based Utility’ s screens and the Bridge’s online technical support resources (all information is read-only). Y ou can also upgrade the Bridg e’ s ...

  • Linksys WET54GS5 - page 49

    43 Appendix A: Troublesh ooting Common Problems and So lutions Wireless-G Ethernet Bridge with 5-P ort Switch Appendix A: Troubleshooting This appendix consists of two parts: “Common Problems and Solutions” and “F requently Asked Questions. ” This appendix provides solutions to problems that may occur d uring the installation and operation ...

  • Linksys WET54GS5 - page 50

    44 Appendix A: Troublesh ooting Frequently Asked Questions Wireless-G Ethernet Bridge with 5-P ort Switch 4. The Bridge- enabled PC won’ t communicate w ith a wir eless-enabl ed PC or printer . Perform the following steps: • Check that the wireless-enabled PC or printer is on t he same wireless network as the PC using the Bridge . • Make sure ...

  • Linksys WET54GS5 - page 51

    45 Appendix A: Troublesh ooting Frequently Asked Questions Wireless-G Ethernet Bridge with 5-P ort Switch Can I run an ap plication from a remote computer over the wireless network? This will depend on whether or not the application is des igned to be used over a network. Consult the application’ s user guid e to determine if it supports operatio ...

  • Linksys WET54GS5 - page 52

    46 Appendix A: Troublesh ooting Frequently Asked Questions Wireless-G Ethernet Bridge with 5-P ort Switch What is ISM b and? The FCC and their counterparts outside of the U.S . have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particula r , is being made availab ...

  • Linksys WET54GS5 - page 53

    47 Appendix B: Wireless Security Security Precautions Wireless-G Ethernet Bridge with 5-P ort Switch Appendix B: Wireless Securit y Linksys wants to make wir eless networking as safe and easy for you as possible . Th e current generation of Linksys products provide several network security features, but they require specific action on your part for ...

  • Linksys WET54GS5 - page 54

    48 Appendix B: Wireless Security Security Threats Facing Wireless Netwo rks Wireless-G Ethernet Bridge with 5-P ort Switch SSID. There are several things to k eep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the optio n of broadcasting the SSID . While this option m ...

  • Linksys WET54GS5 - page 55

    49 Appendix B: Wireless Security Security Threats Facing Wireless Netwo rks Wireless-G Ethernet Bridge with 5-P ort Switch WP A Pre-Shar ed Key . If you do not have a RADIUS server , enter a password in the Pre-Shared key field of 8- 64 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the Router or ...

  • Linksys WET54GS5 - page 56

    50 Appendix C: Upgradin g Firmware Wireless-G Ethernet Bridge with 5-P ort Switch Appendix C: Upgrading Firmware Y ou can use the Bridge’ s Web-based Utility to upgrade the firm war e; however , firmware should be upgraded ONL Y if you experience problems with the Bridge . T o upgrade the Bridg e’ s firmware , follow these instructions: 1. Down ...

  • Linksys WET54GS5 - page 57

    51 Appendi x D: Wind ows Hel p Wireless-G Ethernet Bridge with 5-P ort Switch Appendix D: Windows Help Almost all Linksys wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier . These features can be accessed through Windows Help and are desc ...

  • Linksys WET54GS5 - page 58

    52 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch Appendix E: Glossar y 802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz. 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating fr ...

  • Linksys WET54GS5 - page 59

    53 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch Buffer - A shared or assigned memor y area that is us ed to support and coordinate different computing and networking activities so one isn't held up by the other . Byte - A unit of data that is usually eight bits long Cable Modem - A device that con nects a computer to the ...

  • Linksys WET54GS5 - page 60

    54 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch DTIM ( D elivery T raffic I ndication M essage) - A message included in data packets that can increase wireless efficiency . Dynamic IP Address - A temporar y IP address assigned by a DHCP server . EAP ( E xtensible A uthentication P rotocol) - A general authentication protocol ...

  • Linksys WET54GS5 - page 61

    55 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch IEEE (The I nstitute of E lectrical and E lectronics E ngineers) - An independent institute that de velops networking standards. Infrastructure - A wireless network that is bridged to a wired network via an access point. IP ( I nternet P rotocol) - A protocol used to send data o ...

  • Linksys WET54GS5 - page 62

    56 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch OFDM ( O rthogonal F requency D ivision M ultiplexing) - Frequency transmission that separates the data stream into a number of lower -speed data streams, which are then transmitted in parallel to prevent information from being lost in transit. P acket - A unit of data sent over ...

  • Linksys WET54GS5 - page 63

    57 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch Software - Instructions for the computer . A series of instr uctions that performs a particular task is called a "program". SOHO ( S mall O ffice/ H ome O ffice) - Market segment of professionals who work at home or in small offices. SPI ( S tateful P acket I nspection ...

  • Linksys WET54GS5 - page 64

    58 Appendix E: Glossary Wireless-G Ethernet Bridge with 5-P ort Switch UDP ( U ser D atagram P rotocol) - A network protocol for transmitting data that does not require ackno wledgement from the recipient of the data that is sent. Upgrade - T o replace existing software or firmware with a newer version. Upload - T o transmit a file over a network. ...

  • Linksys WET54GS5 - page 65

    59 Appendix F: Specifications Wireless-G Ethernet Bridge with 5-P ort Switch Appendix F: Specifications Model WET54GS5 Standards IEEE 802.3, 802.3u, 802.11g, 802.11b , 802.1Q, 802.1d, 802.1p Ports 5 10/100 Ports with Auto MDI/MDIX support, Power Buttons Reset Button Cabling T ype Category 5 or better LEDs Power , Diag, Wireless- G Link, Wireless-G ...

  • Linksys WET54GS5 - page 66

    60 Appendix F: Specifications Wireless-G Ethernet Bridge with 5-P ort Switch Operating T emp . 32°F to 104°F (0°C to 40°C) Storage T emp . -4°F to 158°F (-20°C to 70°C) Operating Humidity 10% to 85%, Non-Condensing Storage Humidity 5% to 90%, Non-Condensing W arranty 1 Y ear Limited Warranty ...

  • Linksys WET54GS5 - page 67

    61 Appendix G: Warranty Information Wireless-G Ethernet Bridge with 5-P ort Switch Appendix G: Warrant y Information LIMITED WARRANTY Linksys warrants to Y ou that, for a pe riod of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use . Y our exclusive reme ...

  • Linksys WET54GS5 - page 68

    62 Appendix H: Regulatory Inf ormation FCC Statement Wireless-G Ethernet Bridge with 5-P ort Switch Appendix H: Regulator y Information FCC Statement This product has been tested and complies with the specification s for a Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are designed to pr ovide reasonable protection agai ...

  • Linksys WET54GS5 - page 69

    63 Appendix I: Contact Informa tion Wireless-G Ethernet Bridge with 5-P ort Switch Appendix I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www .linksys.com or ftp.linksys.com Can't find information about a product you want to buy on the web ...

メーカー Linksys カテゴリー Network Router

Linksys WET54GS5のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WET54GS5の取扱説明書
- Linksysの製品カード
- パンフレット
- またはLinksys WET54GS5の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Linksys WET54GS5の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Linksys WET54GS5の取り付け説明書、サービスマニュアル、簡易説明書、またはLinksys WET54GS5のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Linksys WET54GS5の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Linksys WET54GS5デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLinksys WET54GS5を使用するのを助ける技術的文書のことです。説明書は通常、全てのLinksys WET54GS5ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Linksysの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Linksys WET54GS5の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLinksys WET54GS5の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Linksys WET54GS5に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Linksys WET54GS5デバイスの基本機能を使うにあたってのヒント。 Linksys WET54GS5のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Linksys WET54GS5に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLinksys WET54GS5のメーカー/サービスへの連絡先に関する情報。

Linksys WET54GS5についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもLinksys WET54GS5の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLinksys WET54GS5で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)