Vulcan-Hart ML-136221-00G24の取扱説明書

24ページ 1.73 mb
ダウンロード

ページに移動 of 24

Summary
  • Vulcan-Hart ML-136221-00G24 - page 1

    SERVICE MANUAL Heavy Duty Gas Griddles MODEL MLS 924RE ML-135221-00G24 936RE ML-135222-00G36 948RE ML-135223-00G48 960RE ML-135224-00G60 972RE ML-135225-00G72 www.vulcanhart.com 924RE AGE24 MODELS MLS AGE24 ML-135226-00G24 AGE36 ML-135227-00G36 AGE48 ML-135228-00G48 AGE60 ML-135229-00G60 AGE72 ML-135230-00G72 www.wolfrange.com ITW Food Equipment Gr ...

  • Vulcan-Hart ML-136221-00G24 - page 2

    - 2 - TABLE OF CONENTS INSTALLATION ........................................................................................................................... 4 COMPONENT LOCATION ....................................................................................................................... 5 948RE AND AGE48 CONTROL PANEL ................. ...

  • Vulcan-Hart ML-136221-00G24 - page 3

    - 3 - SYMPTOM – ONE BURNER HAS A DELAYED I GNITION; A SEVERAL SECOND LAPSE BETWEEN THE INDICATOR LIGH T TURING ON AND W HEN THE BURNER ACTUALLY LIGHTS. ............................................................................................................................... ... 16 BURNER REMOVAL .............................................. ...

  • Vulcan-Hart ML-136221-00G24 - page 4

    GENERAL INTRODUCTION This manual is prepared for the use of trained service technicians and should only be used by those who are properly qualified. This manual is not intended to be all encompassing. You should read, in it's entirety, the repair procedure you wish to perform to determine if you have the necessary tools, instruments and skills ...

  • Vulcan-Hart ML-136221-00G24 - page 5

    COMPONENT LOCATION 948RE AND AGE48 CONTROL PANEL - 5 - ...

  • Vulcan-Hart ML-136221-00G24 - page 6

    CONTROL PANEL Disconnect the electrical power and follow lockout / tagout procedures The Control Panel holds the thermostats, indicator lights and power switch, and is connected to the Control Plate with a Panel Connector 1. Remove the four screws securing the control panel. There are two screws at each end of the panel. 2. Pull the control panel f ...

  • Vulcan-Hart ML-136221-00G24 - page 7

    HEAT SHIELD Disconnect the electrical powe r and f ollow lockout / tagout procedures The heat shield protects the electrical components and should only be temporarily removed for easier replacement of some the control components. 1. Remove the control panel. 2. Remove screws along the top edge that secure the heat shield. 3. The shield clamps on th ...

  • Vulcan-Hart ML-136221-00G24 - page 8

    Disconnect the electrical power and follow lockout / tagout procedures THERMOSTAT TROUBLESHOOTING SYMPTOM – NO POWER TO THE BURNER S OLENOID 1. Check for loose or excessively greasy/dirty connections at terminals 2. Check for continuity/resistance between the tw o thermostat terminals with wires disconnected A. If you get continuity/resistance wi ...

  • Vulcan-Hart ML-136221-00G24 - page 9

    THERMOSTAT CALIBRATION 1. Each thermostat cont rols a 12” zone of the griddle. Usin g a Surface Pr obe temper ature measurement de vice, observe the temperatures at the center points of the cooking zon es. These points are lo cated by starting 6” fr om the side splash (left or right) and every 12” across the width of the griddle, with a ll po ...

  • Vulcan-Hart ML-136221-00G24 - page 10

    TEMPERATURE DIAL INDICATOR LIGHT KNOB POWER SWITCH KNOB GUARD ( OPTIONAL ) POWER ON/OFF SWITCH The Power Switch controls the power supply to all other electronic com ponents. Disconnect the electrical power and follow lockout / tagout procedures POWER SWITCH TROUBL ESHOOTING SYMPTOM – NO POWER BEING SUPPLIE D TO THE UNIT 1. Check for loose or exc ...

  • Vulcan-Hart ML-136221-00G24 - page 11

    A. If no voltage – check wiring for short or break and check thermostat B. If you have 120V – replace indicator light. Disconnect the electrical power and follow lockout / tagout procedures INDICATOR LIGHT REMOVAL 1. Remove the control panel 2. Label and disconnect wires to the light 3. Squeeze the light retainers and slide the light out throug ...

  • Vulcan-Hart ML-136221-00G24 - page 12

    Disconnect the electrical power and follow lockout / tagout procedures FLAME SWITCH TROUBLESHOOTING SYMPTOM – INDICATOR LIGHTS, THERMOST ATS AND BURNER V ALVES NOT WORKING 1. Check for loose or excessively greasy/dirty terminal connections 2. Check that flame switch probe is fully engulf ed in the pilot flame and glowing cherry red. A. If sensor ...

  • Vulcan-Hart ML-136221-00G24 - page 13

    Disconnect the electrical power and follow lockout / tagout procedures SPARK IGNITOR TROUBLESHOOTING SYMPTOM – NO SPARK BETWEEN PILOT HEAD AND EL ECTRODE 1. Check for loose or greasy/dirty connections at all terminals (including electrode wire) 2. Check for 120 voltage from L1 terminal to ground a. If no voltage check on/off switch and wiring for ...

  • Vulcan-Hart ML-136221-00G24 - page 14

    Disconnect the electrical power and follow lockout / tagout procedures SOLENOID VALVE TROUBLESHOOTI NG SYMPTOM – NO GAS FLOW TO BURNER 1. Check terminals for loose or greasy/dirty connections 2. Check gas pressure – check for orif ice obstructions. 3. With thermostat, indicator light and power switch on – check for 120 voltage between the two ...

  • Vulcan-Hart ML-136221-00G24 - page 15

    PILOT ASSEMBLY REMOVAL Disconnect the electrical power and follow lockout / tagout procedures Shut off gas supply - 15 - 1. Remove control panel and heat shield 2. Reaching underneath the front of the unit, remove the pilot tube fitting and disengage the pilot tube from the pilot. 3. Pull the flame switch probe straight down and out from the snap i ...

  • Vulcan-Hart ML-136221-00G24 - page 16

    Disconnect the electrical power and follow lockout / tagout procedures BURNER TROUBLESHOOTING SYMPTOM – ALL BURNERS HAVE A LOWE R OR HIGHER FLAME THAN NORMAL. 1. Check gas pressure SYMPTOM – ONE OR MORE BURNERS HAVE LOWER FLAME LEVE L THAN THE OTHERS. 1. Check gas pressure 2. Check burner orifice for obstructions 3. Adjust burner air shutter 4. ...

  • Vulcan-Hart ML-136221-00G24 - page 17

    BURNER CLIP (U NDERNEATH ) FLASH TUBE PILOT ASSY IGN ITION PORTS AIR SHUTTER ORIFICE MAIN BURNERS These photos are for reference – it should not be necessary to remove the griddle top to perform the procedures listed in this manual. GAS REGULATOR REGULATOR INSTALLED IN A HORIZONTAL, UPRIGHT POSITION The 900RE and AGE series units must have an ext ...

  • Vulcan-Hart ML-136221-00G24 - page 18

    REGULATOR TROUBLESH OOTING SYMPTOM – UNIT WILL NOT MAINTAIN CONSISTENT PRESSURE 1. Check that vent limiter is not clogged by grease and debris 2. Check store gas pressure before regulator with all equipment on that line turned on and consuming gas A. For natural gas should be between 7” and 14” W.C. B. For propane gas should be between 12” ...

  • Vulcan-Hart ML-136221-00G24 - page 19

    SEQUENCE OF OPERATION Operation is the same for all size griddles. The neutral wire from the power source is directly connected to a terminal on each thermostat, the N terminal on each ignition module and one terminal on the pilot solenoid. 1. The power on/off switch is set to the ON position. 2. Voltage is applied to the following terminals A. Ter ...

  • Vulcan-Hart ML-136221-00G24 - page 20

    WIRING DIAGRAMS WIRING DIAGRAM – 24-INCH GRIDDLE - 20 - ...

  • Vulcan-Hart ML-136221-00G24 - page 21

    WIRING DIAGRAM – 36-INCH GRIDDLE - 21 - ...

  • Vulcan-Hart ML-136221-00G24 - page 22

    WIRING DIAGRAM – 48-INCH GRIDDLE - 22 - ...

  • Vulcan-Hart ML-136221-00G24 - page 23

    WIRING DIAGRAM – 60-INCH GRIDDLE - 23 - ...

  • Vulcan-Hart ML-136221-00G24 - page 24

    WIRING DIAGRAM – 72-INCH GRIDDLE - 24 - ...

メーカー Vulcan-Hart カテゴリー Griddle

Vulcan-Hart ML-136221-00G24のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ML-136221-00G24の取扱説明書
- Vulcan-Hartの製品カード
- パンフレット
- またはVulcan-Hart ML-136221-00G24の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Vulcan-Hart ML-136221-00G24の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Vulcan-Hart ML-136221-00G24の取り付け説明書、サービスマニュアル、簡易説明書、またはVulcan-Hart ML-136221-00G24のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Vulcan-Hart ML-136221-00G24の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Vulcan-Hart ML-136221-00G24デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVulcan-Hart ML-136221-00G24を使用するのを助ける技術的文書のことです。説明書は通常、全てのVulcan-Hart ML-136221-00G24ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vulcan-Hartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Vulcan-Hart ML-136221-00G24の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVulcan-Hart ML-136221-00G24の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Vulcan-Hart ML-136221-00G24に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Vulcan-Hart ML-136221-00G24デバイスの基本機能を使うにあたってのヒント。 Vulcan-Hart ML-136221-00G24のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Vulcan-Hart ML-136221-00G24に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVulcan-Hart ML-136221-00G24のメーカー/サービスへの連絡先に関する情報。

Vulcan-Hart ML-136221-00G24についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもVulcan-Hart ML-136221-00G24の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVulcan-Hart ML-136221-00G24で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)