Briggs & Stratton 5900703の取扱説明書

16ページ 0.59 mb
ダウンロード

ページに移動 of 16

Summary
  • Briggs & Stratton 5900703 - page 1

    A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T riple Catcher Mfg. No. Description 5900703 Clean Sweep Triple Catcher 1735596 Rev. 00 Rev. Date 10/2007 TP 100-4785-00-AT-SMAN Clean Sweep T riple Catc her ...

  • Briggs & Stratton 5900703 - page 2

    THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT) ...

  • Briggs & Stratton 5900703 - page 3

    1 Cover and Ba g Installation Install Cov er Assemb ly ....................................7 Install Collector Bags .......................................7 T ube Installation Low er T ube Installation ....................................8 Connecting Upper and Middle T ube ................8 Collector Installation and Remov al Collector Installation ...

  • Briggs & Stratton 5900703 - page 4

    Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. 2 Safety Rules and Information SAFETY DECALS This unit ...

  • Briggs & Stratton 5900703 - page 5

    CA UTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet, as well as the Operator’s Manual for the tractor and any other attachments. Never operate on slopes greater than 17.6% (10°). After Operation Remove any debris from the screen on the underside of the lid. ...

  • Briggs & Stratton 5900703 - page 6

    4 BAFFLE INSTALLATION 1. Determine which baffle to use (See Chart). 2. Lift side discharge chute (H, Figure 1). 3. Insert baffle (F) through discharge opening and posi- tion baffle into place. 4 . Tighten carriage bolts (A) and locknut(s) (E) on baffle (F). 5 . Tighten carriage bolt (B) and locknut(s) (E) on baffle (F). 6. Position baffle (G) into ...

  • Briggs & Stratton 5900703 - page 7

    5 Component Installation Figure 3. Lower Chute to Boot Installation A. Latch Pin B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 D. Lower Chute E. Locknut, Center Lock, 5/16-18 F. Rubber Strap G. Locknuts, Whiz Lock, 5/16-18 H. Rod, Boot Mount I. Capscrew, Hex Head, 5/16-18 x 1-1/4 J. Capscrew, Hex Head, Thin, 5/16-18 x 1 D B C F A G G H I J E LO ...

  • Briggs & Stratton 5900703 - page 8

    6 Bag and Cover Support Installation INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 5) to upright support (A) using the capscrews (C) and the locknuts (D). A B Figure 5. Install Bag and Cover Support A. Upright Support B. Bag and Cover Support C. Capscrews, 3/8-16 x 1 D. Locknuts, 3/8-16 D C ...

  • Briggs & Stratton 5900703 - page 9

    Cover and Bag Installation 7 Figure 6. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 6) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D). INSTALL COLLECTOR BAGS 1. ...

  • Briggs & Stratton 5900703 - page 10

    T ube Installation 8 LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 8). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole closest to knob in strap completely over locknut (E). CONNECTING UPPER AND MIDDLE TUBE 1. Slide the upper tube (A, Figure 9) into cover (B) align- ing r ...

  • Briggs & Stratton 5900703 - page 11

    9 A. Hitch Support Assembly J. Deflector B. Cover K. Nut & Capscrew C. Pins L. Mounting Plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge I. Strap, Boot R. Ridge Cutout E Q B COLLECTOR INSTALLATION Note: See previous pages for more detailed installation ...

  • Briggs & Stratton 5900703 - page 12

    10 Carrier Installation Figure 12. Front Weight Carrier Installation A. Holes D. Rod B. Capscrews, E. Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknuts, 1/2-13 FRONT WEIGHT CARRIER INSTALLATION 1. Install carrier (F, Fgure 12) as shown securing with capscrews (B), and locknuts (C). 2. Secure required weights using rod (D) and safety clip ...

  • Briggs & Stratton 5900703 - page 13

    11 Hitch Plate and Back Plate Installation FLAT STYLE BUMBER 1. Remove and discard hardware holding heat shield (B, Figure 13) to upper and lower bumper (E). 2. Open existing holes (F) in heat shield (B) and upper & lower bumper (E) to 17/32”. 3. Install hitch plate (A) to upper and lower bumper (E) keeping heat shield (B) in between. Secure ...

  • Briggs & Stratton 5900703 - page 14

    12 Grass Catcher Removal an d Attachment REMOVING THE GRASS CATCHER 1. Remove the hair pin clips (B, Figure 16) and hinge pins (D) and remove the cover (A). A B C D Figure 16. Remove the Cover A. Cover C. Hinge B. Hair Pin Clip E. Hinge Pin 2. Remove the bags (A, Figure 17) by tilting them off their hooks. Empty any grass out of the bags. Figure 17 ...

  • Briggs & Stratton 5900703 - page 15

    13 Grass Catcher Removal and Attachment ATTACHING THE GRASS CATCHER 1. Set the back plate and support (A, Figure 19) onto the pins of the hitch plate (C). Secure with rod (D) and hair pin (B). 2. Hook the bags on the back plate (Figure 7). 3. Install the catcher cover (A, Figure 7) and secure with the hinge pins (D, Figure 6) and hair pin clips (D) ...

  • Briggs & Stratton 5900703 - page 16

    Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Snapper.com Briggs & Stratton Yard Power Products Group Copyright © 2006 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Simplicity Mfg. ...

メーカー Briggs & Stratton カテゴリー Lawn Mower

Briggs & Stratton 5900703のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 5900703の取扱説明書
- Briggs & Strattonの製品カード
- パンフレット
- またはBriggs & Stratton 5900703の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Briggs & Stratton 5900703の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Briggs & Stratton 5900703の取り付け説明書、サービスマニュアル、簡易説明書、またはBriggs & Stratton 5900703のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Briggs & Stratton 5900703の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Briggs & Stratton 5900703デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBriggs & Stratton 5900703を使用するのを助ける技術的文書のことです。説明書は通常、全てのBriggs & Stratton 5900703ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Briggs & Strattonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Briggs & Stratton 5900703の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBriggs & Stratton 5900703の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Briggs & Stratton 5900703に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Briggs & Stratton 5900703デバイスの基本機能を使うにあたってのヒント。 Briggs & Stratton 5900703のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Briggs & Stratton 5900703に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBriggs & Stratton 5900703のメーカー/サービスへの連絡先に関する情報。

Briggs & Stratton 5900703についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBriggs & Stratton 5900703の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBriggs & Stratton 5900703で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)