Quantum 3214の取扱説明書

32ページ 0.77 mb
ダウンロード

ページに移動 of 32

Summary
  • Quantum 3214 - page 1

    TM OWNER INSTALLATION AND USER MANUAL Series 3000 Models 3214, 3314, 3316 & 3414 Automatic Garage Door Opener For Sectional Overhead Residential Doors Only DO NOT USE ON ONE PIECE DOORS CONTENTS Installation …................ 2 Wireless Keyless Entry Installation ..... 20 Features ……………….. 4 Opening & Closing Force Adjustment ...

  • Quantum 3214 - page 2

    2 Read These Important Safety Rules Before Proceeding IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury of death: READ AND FOLLOW ALL INSTA LLATION IN- STRUCTIONS. Install only on a properly bala nced garage door. An improperly balanced do or could cause severe injury. Have a qualified service person make re- pairs to ...

  • Quantum 3214 - page 3

    3 Veuillez lire ces règles de sécurité impor tantes avant de commencer les travaux IMPORTANT —NOTICE D’INSTALLATION— AVERTISSEMENT –POUR REDUIRE LES RISQUES DE BLES SURES MORTELLES LISEZ CETTE NOTICE ET CONFORMEZ-VOUS AUX INSTRUCTIONS. NE POSEZ CET OUVRE-PORTE QUE SUR UNE PORTE DE GARAGE CORRECTEMENT ÉQUILI- BRÉE. UNE PORTE MAL ÉQUILI ...

  • Quantum 3214 - page 4

    4 Automatic Garage Door Opener – For Residential Doors Only FEATURES 1. Open and Close Cycle Control: Allo ws garage door to be started and stopped by push button, transmitte r or wall station. The next impulse sends garage do or in opposite direction. 2. Emergency Disconnect: Manual disconnect permit- ting operation of door during power failure ...

  • Quantum 3214 - page 5

    5 IMPORTANT PRE-ASSEMBLY CHECK If assembling a motor head unit from a factory sealed box skip this check. Every Power Head Unit is factory tested and shipped with the limit switch adjustment in the door CLOSED position. If the Motor Power Head Unit has been powere d up before assembly, perform the following steps to insu re that the limit switch ad ...

  • Quantum 3214 - page 6

    6 Step 1: Attaching Motor Po wer Head Unit to Rail Before assembly, align sprocket/coupli ng cogs to match notche s of driver gear. Rotate the Motor Spline to position Driv er Gear so that the nearest notch in Driver Gear is directly behind Motor Spline, as illustrated. Note: Do not rotate more th an ½ turn. Place opposite end of rail on temporary ...

  • Quantum 3214 - page 7

    7 Step 3: Attach Unit to Front Wall Bracket Raise the front end of the opener and attach it to the front wall bracket, using the ¼” x 4” hex head bolt and the supplied ¼” plasti c insert nut. Take care not to over tighten nut; tighten only until end of bolt is flush with outside of nut. NOTE: If you have a torsion spring counter- balance sy ...

  • Quantum 3214 - page 8

    8 Step 6: Mounting Door Bracket Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your garage door m anu- facturer for their recommendations. Reinforce light weight doors, as illustrated. For wood doors, mount door brac ket, using two 1/4”-20 x 2” carriage bolts and 1/4” nuts suppli ed, on cente ...

  • Quantum 3214 - page 9

    9 Step 9: Installing Deluxe Wireless Wall Station (if included) Install all wall controls out of the reach of children and in a location where the door can be seen before activating. Do no t mount push buttons near or next to ga- rage door. Locate a convenient place to mount wall station. To keep wall sta- tion out of the reach of children, me asur ...

  • Quantum 3214 - page 10

    10 Step 12: Install Wireless Infrared Safety Sensors Wall Mounting Bracket (If Included) Select a mounting position 5 inches abo ve the floor to center line of wall bracket. The EMITTER and TRANSPONDER units must be mounted inside the doo r opening to minimize any interference by the sun; however, the sen sors must be mounted against the door track ...

  • Quantum 3214 - page 11

    11 Step 15: Install Wired Infrared Safety Sensor Wall Mounting Brackets Use the following instructions if your opener is equipped with Wired Infrared Safety S ensors. If you just installed the Wireless Infrared Safety Sen - sors go to step 20. Select a mounting position 5 inches abo ve the floor to center line of wall bracket. The sending and recei ...

  • Quantum 3214 - page 12

    12 Step 17: Install Wiring for Wired Infrared Safety Sensor Identify which side of the garage door opening (if any) the sun is “likely” to shine on to. Since sunlight may affect infrared safety sensors , you should moun t the sending unit on the side of the door opening exposed to the sun. Uncoil the wires from the infrared safety sensors and r ...

  • Quantum 3214 - page 13

    13 Step 19: Mount Wired Infrared Safety Sensors Attach the sending and receiv- ing units to the “U” brackets by inserting their tabs into their respective holes. Step 20: Connecting Electrical Power To reduce the risk of electrical shock, connect the po wer cord only to a properly grounded 3 prong, 120 v olt outlet . Do not use an extension cor ...

  • Quantum 3214 - page 14

    14 Step 21: Wireless Wall Station Security Co de Change and Programming Note: The follo wing steps describe the process to change the Wireless Wall Station security code and to program the Wireless Wall Station to the open er. IMPORTANT: You MUST change the Wireless Wall Station security code prior to programming the device to th e power head unit. ...

  • Quantum 3214 - page 15

    15 Step 22: Alignment of the Wireless Infrared Safety Sensors Use the following instructions if your opener is eq uipped with Wireless Infrared Safety Sen- sors. If your opener is equipped with Wired Infrar ed Safety Sensors proceed to step 23 . IMPORTANT: This infrared beam sensor send s an invisi ble beam of light from the emitter u nit to the tr ...

  • Quantum 3214 - page 16

    16 Step 23: Alignment of the Wired Infrared Safety Sensors Use the following instructions if your opener is eq uipped with Wired Infrared Safety Se nsors. Otherwise proceed to step 24. IMPORTANT: This infrared beam sensor send s an invi sible beam of light from the sending unit to the receiver unit across from the path way of the door. The door ope ...

  • Quantum 3214 - page 17

    17 Programming Transmitter to Power Head Unit Note: Do not press any button on the Transmitter until instruc ted 1. Press the PROGRAM Switch button located on the garage doo r power head unit once. The red PROGRAM STATUS light on the motor power head unit and overhea d lamp will turn on and remain lit for one minute, indicating that it is ready to ...

  • Quantum 3214 - page 18

    18 Step 27: Connecting Door Arm to Door Door Mounted Bracket Visually align cushion arm con necting hole with middle hole of door bracket by rotating tube sect ion in appropriate direction. Release trolley (cushion arm attached ) with manual release cord and pull troll ey a few inches toward mot or. Now rotate cushion arm tube section 2 t urns coun ...

  • Quantum 3214 - page 19

    19 Step 29: Setting Door Opening Travel Do not use adjustments to compensate for a po orly balanced door. This will interfere w ith the proper operation of the trav el adjustments and may damage door. The door opener is as sembled with the open travel adjustment preset for a typical door, but all doors should be adjusted to stop as close a s possib ...

  • Quantum 3214 - page 20

    20 Step 31: Programming Wireless Keyless Entry (If Included) NOTE : To facilitate installation, program the Keyless Entry statio n to the opener before mounting to wall. WARNING: During programming the garage door may operate. Keep people and objects clear of th e moving door to prevent door damage or possible personal injury. NOTE: Before programm ...

  • Quantum 3214 - page 21

    21 Adjustment # 1 Opening and Closing Force This garage door opene r is built with a safety system that a llows the door to reverse in the close dire ction and stop in the open direction. This must be adju sted so your opener does not us e excessive f orce in the down direction or react to the weight of the door during upwa rd travel. CLOSING FORCE ...

  • Quantum 3214 - page 22

    22 Adjustment # 2 Contact Obstruction Sensing (Closing Direction) The opener is designed to automatically reverse the d oor during closing travel whenever it com es in contact with an object up to the last 1 inch of travel above the floor. An object on the floor with a height less than 1” will cause the door to stop. (Test according to instructi ...

  • Quantum 3214 - page 23

    23 IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of severe injury of death: Before you proceed, please thoroughly read the safety ru les on page 2 and the f ollowing operating instructions. Operate only when opener is properly adjusted a nd the door is visible and unobstru cted. READ AND FOLLOW ALL INSTALLA TION IN- STRUCTIONS. Always k ...

  • Quantum 3214 - page 24

    24 HOW TO ACTIVATE THE OPENER Never let children operate or play with door controls. Keep remote control away from children. Use any of the following devices: 1. The Remote Control Transmitter; momentary push of the button and the door will start to move. 2. The Wall Station Up/Down button; push momentarily the button until the door sta rts to move ...

  • Quantum 3214 - page 25

    25 HOW TO OPERATE THE WIRELESS WALL STATION (If Included) Never let children operate or play with door controls. Keep remote control away from children. The Wireless Wall Station Provides the Following Fe atures: 1. Momentarily pressing the UP/DO W N button activates the door. An open door will close and a closed do or will open. 2. Momentarily pre ...

  • Quantum 3214 - page 26

    26 HOW TO OPERATE THE DOOR MANUALLY – Emergency Release Disconnect The door should be fully closed if possible, weak or broken springs could allo w an open door to fall rapidly. Property damage or serious personal injury could result. Do not use the manual release knob to pull the door open or closed. Do not stand near o r in the path of door whe ...

  • Quantum 3214 - page 27

    27 MAINTENANCE OF YOUR OPENER SYSTEM Test door opener monthly. The garage door MUS T reverse on contact with a 1 inch high solid test ob- ject on the floor. If adjusting either the force o r the limit of travel, retest the door opener. Failure to ad- just the opener properly may cause severe injury of death. KEEP GARAGE DOORS PROPERLY BAL ANCED. Se ...

  • Quantum 3214 - page 28

    28 TROUBLE SHOOTING SECTION SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Opener won’t work from wall button or radio control. No power to opener. Short circuit in wires to opener o r wall button. Motor Protector trips open due to ex- cessive use. Check cord to outlet , wall switch and circuit breaker. Isolate by disconnecting the wires at the opener ...

  • Quantum 3214 - page 29

    29 Parts Breakdown Rail Assembly – All Models ...

  • Quantum 3214 - page 30

    30 Parts Breakdown Power Head Assembly – All Models #. Part # Description Per Unit #. Part # Description # Per Unit 1. 15716 7 Frame 1 17. 157496 5/16” Motor Spacers 3 2. 29212 3 Motor – 1/2 H.P. 1 18. 157166 Wired Sensor Mounting Bracket 2 3. 30613 7 Motor Control Board (a ll models) 1 18a. 157159 Wireless Sensor Wall Mou nting Bracket 2 4. ...

  • Quantum 3214 - page 31

    31 QUANTUM ACCESSORIES Three Button mini/visor Transmitter Part#302083 Controls up to 6 doors or wireless ac- cessories. I ncludes visor clip. Wired Deluxe Wall Station Part# Allows independent door up/do wn con- trol and overhead light on/off control. Unit will fit over a standard electrical outlet box. Wireless Deluxe Wall Station Part#30 2090 Co ...

  • Quantum 3214 - page 32

    32 Questions? For quick answers and helpful advice, Call Toll Free 1-800-305-4349 LIMITED LIFETIME WARRANTY The Manufacturer warrants that the Quantum™ garage door ope ner will be free from defects in materials and workmanship for a per iod of five years (3214, 3314), ten years (3316), and fifteen yea rs (3414). Electronic components are warrante ...

メーカー Quantum カテゴリー Garage Door Opener

Quantum 3214のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3214の取扱説明書
- Quantumの製品カード
- パンフレット
- またはQuantum 3214の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Quantum 3214の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Quantum 3214の取り付け説明書、サービスマニュアル、簡易説明書、またはQuantum 3214のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Quantum 3214の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Quantum 3214デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQuantum 3214を使用するのを助ける技術的文書のことです。説明書は通常、全てのQuantum 3214ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Quantumの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Quantum 3214の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQuantum 3214の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Quantum 3214に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Quantum 3214デバイスの基本機能を使うにあたってのヒント。 Quantum 3214のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Quantum 3214に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQuantum 3214のメーカー/サービスへの連絡先に関する情報。

Quantum 3214についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもQuantum 3214の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQuantum 3214で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)