Delta 31の取扱説明書

16ページ 2.13 mb
ダウンロード

ページに移動 of 16

Summary
  • Delta 31 - page 1

    INSTRUCTION MANUAL 6" Belt and 12" Disc Abrasive Finishing Machine (Model 31-731) P ART NO. 420-01-651-0013 - 05-28-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-80 ...

  • Delta 31 - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 31 - page 3

    3 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment shou ...

  • Delta 31 - page 4

    4 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembl ...

  • Delta 31 - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta 31 - page 6

    6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause ...

  • Delta 31 - page 7

    7 FOREWORD Delta Model 31-731 is a abrasive finishing machine. The Delta Model 31-731 includes two tilting tables, 4½" arbor pulley , V -belt, 80-grit aluminum oxide belt and 50-grit aluminum oxide disc. FUNCTIONAL DESCRIPTION UNP ACKING AND CLEANING YOUR MACHINE IS SHIPPED WITHOUT BEL T TENSION APPLIED TO THE SANDING BEL T . BEFORE OPERA TIN ...

  • Delta 31 - page 8

    8 ALIGNING PULLEYS, ASSEMBLING BEL T AND ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE Using a straight edge (A) Fig. 6, make certain the motor pulley (B) is aligned with the arbor pulley . If necessary , the motor pulley (B) can be adjusted on the motor shaft by loosening set screw and moving the motor pulley (B) in or out as needed ...

  • Delta 31 - page 9

    9 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING THE ABRASIVE FINISHING MACHINE T o start the machine, push “ON” button (A) Fig. 10. T o stop the machine, push “OFF” button (B). LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the tool is not in use, the switch should be locked in the OFF position using a padlock (A) ...

  • Delta 31 - page 10

    10 3. Loosen tracking lock knob (D) Fig. 14, and while rotating the belt (F) by hand, as shown, tighten or loosen tracking knob (E) until the belt is running true on the pulleys. 4. Then jog the machine on and off to check further if the belt is tracking properly . If the belt is leading to one side or the other , very gently turn the tracking knob ...

  • Delta 31 - page 11

    11 ADJUSTING POSITION OF SANDING ARM DISCONNECT MACHINE FROM POWER SOURCE. The sanding arm can be positioned in the vertical or horizontal position, or at any desired angle in between as follows: 1. Loosen two bolts (A) Fig. 18, move the sanding arm to the desired position, and tighten the two bolts. THE SANDING ARM SHOULD NEVER BE REPOSITIONED WHI ...

  • Delta 31 - page 12

    12 ADJUSTING T ABLE SQUARE WITH SANDING DISC DISCONNECT MACHINE FROM POWER SOURCE. 1. Place an accurate square (C) Fig. 23, on the table with one end of the square against the disc. 2. Loosen the table locking knobs (A) Fig. 23, which are located on each end of the table and move the table until it is at 90 degrees to the disc. Then tighten the tab ...

  • Delta 31 - page 13

    13 ADJUSTING THE PLA TEN The platen (A) Fig. 24, is set at the factory 1/32 of an inch higher than the crown of the drums (B). This allows the belt, when properly tensioned, to lay flat on the platen and eliminate stretching and bulging which might occur if the platen is not at the right height. When using the machine with a loose belt for "st ...

  • Delta 31 - page 14

    14 NOTES ...

  • Delta 31 - page 15

    15 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta 31 - page 16

    The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...

メーカー Delta カテゴリー Sander

Delta 31のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 31の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta 31の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta 31の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta 31の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta 31のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta 31の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta 31デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta 31を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta 31ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta 31の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta 31の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta 31に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta 31デバイスの基本機能を使うにあたってのヒント。 Delta 31のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta 31に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta 31のメーカー/サービスへの連絡先に関する情報。

Delta 31についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta 31の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 31で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)