Haier HPU-44H03の取扱説明書

33ページ 0.43 mb
ダウンロード

ページに移動 of 33

Summary
  • Haier HPU-44H03 - page 1

    Packaged unit Operation Manual AP42NACAAA AU42NAIAAA (HPU-44H03) AP42NACMAA AU42NAIMCA (HPU-42C03) No.0010571223 Ion TIMER ON TIMER OFF : AM PM AM PM AM PM : TIMER CLOCK SET TIME TIME SLEEP A U T O LO MED HI SET TEMP C ROOM TEMP TEMP TEMP SWING MODE FAN SPEED ON OFF : AM TEMP SWING FAN ON OFF MODE SLEEP SET CLOCK TIMER RESET LOCK ...

  • Haier HPU-44H03 - page 2

    Operation Content Cautions Parts Indoor unit Outdoor unit Operation display Wireless remote control Operation Auto Cooling operation Dry operation Heating operation Fan operation Sleep T imer ON and T imer OFF Air flow adjustment Operation hints Energy saving Cautions for the operation Maintenance Air filter and unit cleaning Before/after season ma ...

  • Haier HPU-44H03 - page 3

    CAUTIONS 1 Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The v ...

  • Haier HPU-44H03 - page 4

    CAUTIONS 2 For the purpose of safety , the air conditioner must be properly grounded in accordance with specifications. Always remember to unplug the air conditioner before opening inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. All electrical repairs must b ...

  • Haier HPU-44H03 - page 5

    Parts 3 1 2 3 4 1 Outlet grill 2 Operation panel 3 Inlet grill 4 Air filter 5 Remote-controller Indoor unit AM TEMP SWING FAN ON OFF MODE SLEEP SET CLOCK TIMER RESET 5 LOCK 6 7 Outdoor unit Air inlet 6 7 [At side and rear] Air outlet ...

  • Haier HPU-44H03 - page 6

    Parts Manual Operation Ion TIMER ON TIMER OFF : AM PM AM PM AM PM : TIMER CLOCK SET TIME TIME SLEEP A U T O LOW MID HIGH SET TEMP C ROOM TEMP TEMP TEMP SWING MODE F AN SPEED ON OFF 7 6 5 3 2 9 8 10 1 4 : 4 Remote controlled operation Power ON/OFF Used for unit start and stop. SWING Used to set auto fan direction MODE Used to select AUTO run, COOL, ...

  • Haier HPU-44H03 - page 7

    Operation 5 Clock set When unit is started for the first time and after replacing batteries in remote controller , clock should be adjusted as follows: Press CLOCK button, "AM"or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min . If the button is kept depressed, time will change quickly . Aft ...

  • Haier HPU-44H03 - page 8

    AM TIMER CLOCK SET TIME TIME SLEEP A U T O LOW MID HIGH SET TEMP C TEMP TEMP SWING MODE F AN SPEED ON OFF : Operation 6 Auto Manual Operation Remote-controlled Operation 1 3 Note: During Auto run operation, temp. setting will not be shown in LCD display , unit will select heating, cooling or fan operation according to the room temp. 2 AUTO AM TEMP ...

  • Haier HPU-44H03 - page 9

    Operation 7 Cooling Manual Operation AM TIMER CLOCK SET TIME TIME SLEEP SET TEMP TEMP TEMP SWING MODE F AN SPEED ON OFF : 2 3 1 5 4 C Remote-controlled Operation Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP and SWING mode) Press MODE button. For each press, operation mode changes as follo ...

  • Haier HPU-44H03 - page 10

    Operation 8 Dry Manual Operation Remote-controlled Operation Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP and SWING mode) Press MODE button. For each press, operation mode changes as follows: Select Drying operation shows" " Dry operation starts Select temp. button Press TEMP bu ...

  • Haier HPU-44H03 - page 11

    Operation 9 Heating Manual Operation Remote-controlled Operation Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP and SWING mode) Press MODE button. For each press,operation mode changes as follows: Select Heating operation " " appears and Heating operation starts. Press F AN button ...

  • Haier HPU-44H03 - page 12

    Operation 10 Fan Manual Operation Remote-controlled Operation Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP and SWING mode) Press MODE button. For each press,operation mode change s as follows: Select Fan operation shows " ", Fan operation starts. Press ON/OFF button Unit stops r ...

  • Haier HPU-44H03 - page 13

    Operation 11 SLEEP AM TIMER CLOCK SET TIME TIME SLEEP LOW MID HIGH SET TEMP C TEMP TEMP SWING MODE F AN SPEED ON OFF : Remote-controlled operation Before sleeping you can press the Sleep button. The conditioner will run under comfort sleep mode, and give you a comfort sleep. Usage of the Sleep function After starting, set the Run mode and press the ...

  • Haier HPU-44H03 - page 14

    Operation 12 T imer on/off operation Manual Operation Remote controlled operation TIMER operation TIMER ON AM AM : TIMER CLOCK SET TIME TIME SLEEP LOW MID HIGH ROOM TEMP TEMP TEMP SWING MODE F AN SPEED ON OFF : Set Clock correctly before starting T imer operation (refer to page 5) Y ou can let unit start or stop automatically at following times: Be ...

  • Haier HPU-44H03 - page 15

    Operation 13 T imer on-off function Manual Operation Remote controlled operation TIMER ON-OFF (1) After unit start, select your desired operation mode. Operation mode will be displayed on LCD. (2) TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: (3) Timer setting for TIMER O ...

  • Haier HPU-44H03 - page 16

    Operation 14 Air flow adjustment Swing louvers (V ertical louvers) Horizontal louvers (Adjust by hand) Up and down Adjust the louvers by hand to proper position. Put louvers at up position in cooling and down position in heating mode. This will be helpful to keep an even room temp. Note: In cooling or dry operation, don't put horizontal louver ...

  • Haier HPU-44H03 - page 17

    Operation hints 15 Unit operation Protection devices inside the unit will activate to stop unit operation, when ambient temp. is extremely low or high. When unit is running under high humidity in cooling or dehumidifying mode, conden- sate might appear at outlet grill. 3-min delay protection Fan speed changes Cold draft prevention Use objectively D ...

  • Haier HPU-44H03 - page 18

    Energy saving 16 Keep proper room temp. T oo cold or too warm is no good to your health, and power consumption will be increased as well. Air filter should be periodically cleaned If air filter is clogged: It will cause poor cooling and heating efficiency , higher power consumption and even problem may occur . In cooling operation, water will flow ...

  • Haier HPU-44H03 - page 19

    Cautions for the operation 17 Use control panel to operate the unit. Don't press buttons unless necessary . Use fuses of the right capacity . Never use iron or copper wires instead. Don't touch moving outlet grills. Keep a smooth air flow to inlet and outlet of both indoor and outdoor unit. T o avoid accident, don't insert any object ...

  • Haier HPU-44H03 - page 20

    Maintenance 18 Disconnect power supply Don't touch it with wet hand Don't wash with hot water or solvent to clean the unit Don't use hot water over 40 C, as this may cause damage to air filter . Wipe air filter carefully . Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with clean and soft cloth. If air c ...

  • Haier HPU-44H03 - page 21

    Maintenance 19 After season maintenance Before season maintenance Let the unit run in Fan mode for half a day in a fine weather to dry completely the unit inside. T urn off the unit and pull out power plug. There might be certain power consumption even if unit is stopped. Clean air filter and indoor unit, cover outdoor unit after cleaning. Check if ...

  • Haier HPU-44H03 - page 22

    T rouble shooting 20 Followings are not problems Sound of water flowings are not problems. Sound of cracking is heard. Smells are generated. During operation, white fog or steam comes out of indoor unit. In cooling operation, unit switches to fan operation. Unit will not restart after stop. Won't start? No outlet air or fan speed can't be ...

  • Haier HPU-44H03 - page 23

    When problems occur? 21 Before ask for services, please first check your unit against following. Air conditioner won't start. Is power supply switch turned on? Power supply switch is not set at ON. Are operation controlls adjusted correctly as specified? Are horizontal louvers at up position (in heating mode)? Is there any direct sunlight in t ...

  • Haier HPU-44H03 - page 24

    Indoor & outdoor unit connection 22 power cable length Approx 1.5m Approx 2m pipe direction Left Rear Right Bottom Over 10cm Over 10cm Over 10cm Over 10cm Over 10cm Over 60cm Over 15cm Over 100cm ...

  • Haier HPU-44H03 - page 25

    Indoor & outdoor unit connection 22 power cable length Approx 1.5m Approx 2m pipe direction Left Rear Right Bottom Over 10cm Over 10cm Over 10cm Over 10cm Over 10cm Over 60cm Over 15cm Over 100cm ...

  • Haier HPU-44H03 - page 26

    23 T ools necessary T ools necessary Remote controller Cement nail Drain hose Heat-insalution pipe L-shaped metal Fall-prevention fitting metal Wire clip Drain elbow Self-tapping scerw Rubber pad Hexagon wrench W all hole cover Piping hole cover Dry battery 7 # Putty No. QTY Shape and description Parts in the following list are accessories for the ...

  • Haier HPU-44H03 - page 27

    24 Installation procedures Display of whole unit Installation of outdoor unit 190 340 190 580 Installation dimension of outdoor unit (mm) T ry to bring the packed unit to the installation place. When it is inevitable to unpack the unit, be careful not to damage the unit. Wrap it with nylon etc. After unpacking, be sure to put it with the front side ...

  • Haier HPU-44H03 - page 28

    Installation procedures 25 Installation of indoor unit Selection of installation place Place where it is easy to route drainage pipe and outdoor piping. Place away from heat source and with less direct sunlight. Place where cool and warm air could be delivered evenly to every corner of the room. Place near power supply socket. Leave enough space ar ...

  • Haier HPU-44H03 - page 29

    26 Installation of fall-prevention fitting metal: Fix the fitting metal to the wall by screws so that there is no clearance between them. With the unit set up vertically , fix the fitting metal to the unit with screws while making an adjustment at the long portion of the hole so that there is no clearance between the upper surface and the fitting m ...

  • Haier HPU-44H03 - page 30

    27 2. Piping connection of indoor unit Arrangement of piping and drainage pipe After opening inlet grill, you will see a control box as shown in the Fig. Remove the cover before working. Cut away , with a hammer or a saw , the lid for piping according to piping direction. Insulation material Copper tube Drain hose Connecting electric cable for indo ...

  • Haier HPU-44H03 - page 31

    28 3. Piping connection of outdoor unit. Connect the connecting pipe and inlet and outlet liquid pipe according to the piping method. Installation procedures When piping is longer than 5 m, charge additional refrigerant specified in this list. Pipe length Refrigerant charge (g) 5m 10m 15m 20m 500 750 250 4.Purging method Discharge the air out of th ...

  • Haier HPU-44H03 - page 32

    29 Electric wiring Note: Electric wiring must be done by qualified person. Use copper wire only , the parameter of connecting cable is H07RN-F4 X 0.75mm 2 . Wiring of indoor unit Insert the cable from outside the wall hole where piping already exist. Pull it out from front. Loosen terminal screws and insert cable end fully into terminal block, then ...

  • Haier HPU-44H03 - page 33

    30 Others 1. Power supply Air conditioner must use an exclusive line (over 30A) When installation air conditioner in a wet place, try to use a circuit breaker against Current leakage. For installation in other places, use circuit breaker as far as possible. Installation inspection and test run: Please operate unit according to this Manual. Items to ...

メーカー Haier カテゴリー Air Conditioner

Haier HPU-44H03のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HPU-44H03の取扱説明書
- Haierの製品カード
- パンフレット
- またはHaier HPU-44H03の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Haier HPU-44H03の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Haier HPU-44H03の取り付け説明書、サービスマニュアル、簡易説明書、またはHaier HPU-44H03のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Haier HPU-44H03の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Haier HPU-44H03デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHaier HPU-44H03を使用するのを助ける技術的文書のことです。説明書は通常、全てのHaier HPU-44H03ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Haierの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Haier HPU-44H03の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHaier HPU-44H03の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Haier HPU-44H03に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Haier HPU-44H03デバイスの基本機能を使うにあたってのヒント。 Haier HPU-44H03のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Haier HPU-44H03に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHaier HPU-44H03のメーカー/サービスへの連絡先に関する情報。

Haier HPU-44H03についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHaier HPU-44H03の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHaier HPU-44H03で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)