Posiflex LS-1000の取扱説明書

22ページ 関係なし
ダウンロード

ページに移動 of 22

Summary
  • Posiflex LS-1000 - page 1

    FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply w ith limits for a Class A digital device pursuant to EN55022 and 47 CFR, Part 2 and subpart J of Part 15 ...

  • Posiflex LS-1000 - page 2

    FUNDAMENTAL INFORMA TION MODEL NAME : LS - 1000 CONTENT ( Besides this guide) : Fig . 1 Box content besides this g uide INSTALLATION GUIDES 1. Install the USB or RS232 interface cable onto the scanner by inserting the 8 pin RJ45 type modular plug ( Fig. 2 ) of the cable into the scanner until a firm click is heard. 2. Use the stand fixing screw to ...

  • Posiflex LS-1000 - page 3

    Description Function Scan Window Reads barcodes Object Detector Trigger and wake up scanner automatically when present ed with barcode in its range Beeper Hole Fo r beep tone indication USING THE SCANNER SCANNER INTRODUCTION Features The scanner unit is a compact and space - saving hands - free omni - directional laser scanner . It can operate in a ...

  • Posiflex LS-1000 - page 4

    Wake up scanner When the scanner enters the sleep mode, pressing this switch can wake the scanner up. The sleep mode feature can be programmed using the menu labels from the Programming Guide. NO TE: The default time - out value is set to 10 minutes after laser sl e p t , 30 minutes after motor slep t . When the scanner is in sleep mode, the LED in ...

  • Posiflex LS-1000 - page 5

    SCANNER SETUP (PROGRAMMING) In most of the cases no setup is required. The defaul t setup of the scanner makes the scanner able to detect automatically the most commonly applied bar code types as tabulated above and send the data to the host system as if they are read from an USB or RS232 keyboard . To read the disabled bar code types, t he program ...

  • Posiflex LS-1000 - page 6

    Cover unwanted codes with your hand and present the desired codes, one by one, to the scanner, the scanner beeps once as it accepts each code. When done, again present the < Enter/Exit programming mode > barcode. The scanner beeps twice, once long and once short, and the LED returns to blue. The scanner has b een programmed. Of course you may ...

  • Posiflex LS-1000 - page 7

    SCANNER OPERATION Operating the Scanner The scanner read s barcodes in omni - directional scan mode as regular practice. It can also operate in single - line mode for a better aiming on a specific barcode that is printed on a surface with more than one barcode printed closely. Single Line Scan Mode In this mode the scanner can emit a single line pa ...

  • Posiflex LS-1000 - page 8

    Sleep Mode After the scanner has been inactive for a period of time, the laser automatically turns off; then the motor will turn off and the scanner will enter the “ Sleep Mode ” , the blue status LED keeps blink ing as indication. To wake up the scanner, simply present an object close to the scan window, or press the function button. Note: The ...

  • Posiflex LS-1000 - page 9

    Beeper Indications A beeper gives audible feedback on scanner operation. Beeps Indication One bee p A barcode has been successfully decoded. Four beeps in series This indicates the scanner passed the power on self - test and is operating properly. Two beeps: low - high The scanner has entered programming mode. Two beeps: same tone Scanner has retur ...

  • Posiflex LS-1000 - page 10

    Page 10 make sure that the scanner is installed as instructed in this manual and that all cables are properly connected. If the problem remains, contact your dealer. Problem Diagnostic Tips The scanner window is dirty. Clean the scanner window as described in the Maintenance section. The presented barcode type is not enabled. Use the Programming Gu ...

  • Posiflex LS-1000 - page 11

    The software running on the POS system does not support the data format of the barcode label. Enter/Exit Programming Mode Note: Scan t h is code to enter and exit programming mode. A slightly enlarged image of this code is also printed on the last page of this section for ease of application . PROGRAMMING CODES All framed barcode names represent as ...

  • Posiflex LS-1000 - page 12

    RESET Note: The reading of the “RESET” label turns all the parameters back to default values but leaving the interface mode unchanged. It is suggested to scan also the “ Return to USB default ” or “ Return to RS232 default ” label after this for LS - 1000 scanners. Return to USB default US Keyboard Return to RS232 default Page 12 ...

  • Posiflex LS-1000 - page 13

    Message Terminator - Enter Message Terminator - H.tab Message terminator - None International Keyboard (ALT method) Page 13 ...

  • Posiflex LS-1000 - page 14

    Return to customer default Note: The reading of the label will recover all parameter back to customer default . Codabar Enable Save as customer default Codabar Disable Page 14 ...

  • Posiflex LS-1000 - page 15

    Full ASCII COD E 39 Disable Code 39 Enable Code 39 Disable Full ASCII CODE39 Enable Page 15 ...

  • Posiflex LS-1000 - page 16

    UPC/EAN/JAN Disable UPC/EAN/JAN Enable ITF 2 OF 5 Disable ITF 2 of 5 Enable Page 16 ...

  • Posiflex LS-1000 - page 17

    UPC/EAN ADD ON OFF ADD ON 5 only ADD ON 2 only ADD ON 2 or 5 Page 17 ...

  • Posiflex LS-1000 - page 18

    EAN/UPC +Add on (none mandatory) Force UPC - A to EAN - 13 format enable EAN/UPC + Add on (mandatory) Force UPC - A to EAN - 13 format disable Page 18 ...

  • Posiflex LS-1000 - page 19

    EAN - 13 Convert to ISBN/ISSN Enable EAN - 13 Convert to ISBN/ISSN Disable EAN - 128 Enable EAN - 128 Disable Page 19 ...

  • Posiflex LS-1000 - page 20

    Code 128 Enable Code 128 Disable Code 93 Enable Code 93 Disable Page 20 ...

  • Posiflex LS-1000 - page 21

    Chinese Post Code Enable Chinese Pos t Code Disable Code 32 (Italian Pharmacy Code) Enable Code 32 (Italian Pharmacy Code) Disable Page 21 ...

  • Posiflex LS-1000 - page 22

    MSI enable MSI Disable Enter/Exit Programming Mode Page 22 ...

メーカー Posiflex カテゴリー Barcode readers

Posiflex LS-1000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LS-1000の取扱説明書
- Posiflexの製品カード
- パンフレット
- またはPosiflex LS-1000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Posiflex LS-1000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Posiflex LS-1000の取り付け説明書、サービスマニュアル、簡易説明書、またはPosiflex LS-1000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Posiflex LS-1000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Posiflex LS-1000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPosiflex LS-1000を使用するのを助ける技術的文書のことです。説明書は通常、全てのPosiflex LS-1000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Posiflexの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Posiflex LS-1000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPosiflex LS-1000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Posiflex LS-1000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Posiflex LS-1000デバイスの基本機能を使うにあたってのヒント。 Posiflex LS-1000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Posiflex LS-1000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPosiflex LS-1000のメーカー/サービスへの連絡先に関する情報。

Posiflex LS-1000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPosiflex LS-1000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPosiflex LS-1000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)