Harbor Freight Tools 95668の取扱説明書

30ページ 3.51 mb
ダウンロード

ページに移動 of 30

Summary
  • Harbor Freight Tools 95668 - page 1

    INDUSTRIAL SHAPER/ROUTER Model 95668 SET UP AND OPERA TING INSTRUCTIONS Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyright © 2007 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork con ...

  • Harbor Freight Tools 95668 - page 2

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 2 PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , op era ti ng, in spe ct ion , main te nan ce and cl ea nin g proc edu re s, par ts lis t and asse mb ly diagram. Keep your invoice with this manual. Write the ...

  • Harbor Freight Tools 95668 - page 3

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 3 ELECTRICAL SAFETY 1. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way . Do not use any adapter plugs.Checkwithaqualiedelectri ...

  • Harbor Freight Tools 95668 - page 4

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 4 in. Plugging in power equipment with the Power Switch on, invites accidents. 5. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the Wood Shaper may result in personal injury . 6. Do not overreach. K ...

  • Harbor Freight Tools 95668 - page 5

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 5 SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Wood Shaper . These carry important information. If unreadable or missing, contact Harbor Freight T ools for a replacement. 2. A void unintentional starting. Make sure you are prepared to begin work before turning on ...

  • Harbor Freight Tools 95668 - page 6

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 6 12. Keep the Cutters on the underside of the workpiece whenever possible. This provides a distance guard for the operator . 13. Unplug the Wood Shaper , and always rotate the Spindle by hand to test any new setup to ensure proper Cutter clearance before starting the Wood Shaper . ...

  • Harbor Freight Tools 95668 - page 7

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 7 26. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do ...

  • Harbor Freight Tools 95668 - page 8

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 8 THIS PRODUCT USES A 3-PRONG PLUG Grounded T ools: T ools with Three Prong Plugs T ools marked with “Grounding Required” have a three wire cord and three prong 1. grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunct ...

  • Harbor Freight Tools 95668 - page 9

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 9 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 27 and 28 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y INSTRUCTIONS ...

  • Harbor Freight Tools 95668 - page 10

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 10 5. Place the Wood Shaper’s Work T able (52) upside down on two sturdy blocks that are at least 3-1/2” off the oor . Make sure the Spindle (105) DOES NOT touch the oor or the weight of the Wood Shaper may damage the Spindle. (See Figure G.) 6. Place the Stand assembly o ...

  • Harbor Freight Tools 95668 - page 11

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 1 1 FIGURE H RIGHT FENCE BODY (not Shown) (57) LEFT FENCE BODY (59) FENCE (60) PHILIPS HEAD SCREWS (12) W ASHERS (13) Installing The Safety Guard: 1. Connect the Hold Down Bar (77) to the Hex Post (79) with two Hex Bolts (75) and two Flat W ashers (76). (See Figure I.) 2. Connect t ...

  • Harbor Freight Tools 95668 - page 12

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 12 2. Thread one end of the Draw Bar (121) into the bottom end of the Spindle (105) approximately 10 to 15 turns until tight. (See Figure J.) 3. Insert the Spindle/Draw Bar assembly into the Spindle Housing (1 10) from the top side of the Work T able (52). (See Figure K.) 4. Thread ...

  • Harbor Freight Tools 95668 - page 13

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 13 Router Bit Assembly: 1. Prior to installation, make sure to remove any oil, grease, dirt and debris from the Collet (103, 104), Draw Bar (121), and Spindle Housing (1 10) surfaces before installing a Router Bit. 2. Remove the Spindle (105) as shown on page 12 of this manual. (Se ...

  • Harbor Freight Tools 95668 - page 14

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 14 shaping tasks. The Fences (60) can be set at dif ferent positions to remove material from the entire edge of the wood stock or set at the same position to shape part of the edge. FIGURE P FENCE (60) FENCE (60) LOCK HANDLE (61) KNOB (64) Fence Alignment: 1. T o align the Fences ( ...

  • Harbor Freight Tools 95668 - page 15

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 15 T able Inserts: 1. T able Inserts (53, 53A) are used to reduce wood chips falling into the machine which could cause ying debris. Using the smallest T able Insert also covers any unused portion of the bit below the surface of the Work T able (52). (See Figure R.) 2. Position, ...

  • Harbor Freight Tools 95668 - page 16

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 16 Cutter Direction: 1. The Wood Shaper is capable of operating in two directions by the use of the Forward/Reverse Switch (144). It is very important that the workpiece be fed against the direction of the Cutter rotation. (Cutter not included) (See Figure T .) 2. When the Forward/ ...

  • Harbor Freight Tools 95668 - page 17

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 17 2. Place the required spacers, also called Rub Collars (98, 99, 100), onto the Spindle (105). (See Figure V .) RUB COLLARS (98, 99, 100) SPINDLE (105) CUTTER (NOT INCLUDED) FIGURE V 3. Install the Safety W asher (97) and Upper Spindle Nut (96) securely . T ighten the Upper Spind ...

  • Harbor Freight Tools 95668 - page 18

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 18 the left to lower the Spindle (105). (See Figure Z.) 4. Retighten the Spindl e Hand Knob (92) on the side of the Wood Shaper . DO NOT overtighten the Knob. Only a small amount of tension is needed to keep the Spindle (105) from moving during operation. (See Figure Y .) FIGURE Y ...

  • Harbor Freight Tools 95668 - page 19

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 19 B. Between two Cutters: This set-up has the advantage of making two prole cuts in a single pass. Although there is a Rub Collar (98, 99, 100) beneath a Cutter , this set-up is safer than the previous set-up. Any lifting of the workpiece will still cause the Cutter to make an ...

  • Harbor Freight Tools 95668 - page 20

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 20 Start Up: 1. Once assembly is complete and all adjustments have been made, the Wood Shaper is ready for start up. Always pay attention to any unusual noises and vibrations on every start up, as well as making sure the Wood Shaper operates as intended. 2. Make sure the Fences (60 ...

  • Harbor Freight Tools 95668 - page 21

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 21 6. T ighten the Lock Handle (61) to lock the infeed Fence (60) in position. (See Figure DD.) FENCE (60) INFEED SIDE LOCK HANDLE (61) HAND KNOB (68) FIGURE DD FENCE (60) OUTFEED SIDE 7. Adjust the outfeed Fence (60) so that it is located as far back from the front of the Work T a ...

  • Harbor Freight Tools 95668 - page 22

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 22 T o Set Up The Aluminum Fences For Partial Edge Removal: 1. W ARNING! AL W A YS use the aid of a jig (not included) when shaping small or narrow workpieces. A jig will reduce the chance of your hands coming into contact with the Cutter . 2. Loosen the Lock Handle (61). (See Figu ...

  • Harbor Freight Tools 95668 - page 23

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 23 2. T o reduce this tendency , use a T aper Pin (56). The T aper Pin allows you to anchor and slowly pivot the workpiece into the Cutter as the cut is started. Thus, shaping freehand is more stable and safer . (See Figures HH). W ARNING! AL W A YS use an auxiliary jig (not includ ...

  • Harbor Freight Tools 95668 - page 24

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 24 Pattern Shaping: 1. Sometimes the location of the T aper Pin (56) holes on the Work T able (52) will not always be in the safest position. Y ou can clamp a piece of scrap wood to the Work T able so the edge of the scrap wood can be used as the starting support. (See Figure JJ.) ...

  • Harbor Freight Tools 95668 - page 25

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 25 INSPECTION, MAINTENANCE, AND CLEANING 1. CAUTION! Always make sure the Power Switch (5) of the Wood Shaper is in its “OFF” position and the unit is unplugged from its electrical outlet prior to performing any inspection, maintenance, or cleaning procedures. 2. Before each us ...

  • Harbor Freight Tools 95668 - page 26

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 26 TROUBLESHOOTING Problem Possible Reason Possible Solution The Wood Shaper does not start or the circuit breaker trips. 1. Electrical supply circuit has low voltage or high resistance. 1. Make sure machine is plugged into a working, 1 10 volt, grounded, electrical outlet. The Woo ...

  • Harbor Freight Tools 95668 - page 27

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 27 P ARTS LIST NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. Part # Description Part # Description 1 Side Panel 59 Fence Body (Left) 2 T ie Bar 60 Fence 3 Rubber Foot 61 Lock Handle 4 Philips Head Scr ...

  • Harbor Freight Tools 95668 - page 28

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 28 P ARTS LIST (CONT .) WIRING DIAGRAM Disconnect power from machine before performing any electri- cal service. Failure to do this will result in a shock hazard leading to injury . GREEN BLACK WHITE REAR VIEW OF SWITCH BLACK WHITE REAR VIEW OF SWITCH BLACK WHITE FWD/REV SWITCH CAP ...

  • Harbor Freight Tools 95668 - page 29

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 29 ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. ...

  • Harbor Freight Tools 95668 - page 30

    SKU 95668 For technical questions, please call 1-800-444-3353 P AGE 30 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor , the belts ...

メーカー Harbor Freight Tools カテゴリー Router

Harbor Freight Tools 95668のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 95668の取扱説明書
- Harbor Freight Toolsの製品カード
- パンフレット
- またはHarbor Freight Tools 95668の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Harbor Freight Tools 95668の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Harbor Freight Tools 95668の取り付け説明書、サービスマニュアル、簡易説明書、またはHarbor Freight Tools 95668のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Harbor Freight Tools 95668の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Harbor Freight Tools 95668デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHarbor Freight Tools 95668を使用するのを助ける技術的文書のことです。説明書は通常、全てのHarbor Freight Tools 95668ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Harbor Freight Toolsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Harbor Freight Tools 95668の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHarbor Freight Tools 95668の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Harbor Freight Tools 95668に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Harbor Freight Tools 95668デバイスの基本機能を使うにあたってのヒント。 Harbor Freight Tools 95668のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Harbor Freight Tools 95668に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHarbor Freight Tools 95668のメーカー/サービスへの連絡先に関する情報。

Harbor Freight Tools 95668についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHarbor Freight Tools 95668の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 95668で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)