Honeywell 500の取扱説明書

16ページ 7.2 mb
ダウンロード

ページに移動 of 16

Summary
  • Honeywell 500 - page 1

    INST ALLATION INSTRUCTIONS 62-0304-05 Class 500 Advanced KWh/Demand Meter APPLICATION The Class 500 Meter is a 3-element meter with commu nications. The device is used to moni tor electric power usage of ind ividual loads after the utility meter . Installation must only be performed by qualified pers onnel and in acc ordance with these instructions ...

  • Honeywell 500 - page 2

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 2 S PECIFICATIONS Input V oltage Configuration: 3-wire (Delta) or 4-wire (WYE) Mains V oltage Input: Up to 600 V AC RMS available Input Power: 6 V A maximum rating Current Sensor Rating: Up to 3200 Amp RMS AC available Power Factor: .5 leading or lagging Line Frequ ency: 50-60 Hz Metering Accuracy: ...

  • Honeywell 500 - page 3

    CLASS 500 ADVANCED KWH/DEMAND METER 3 62-0304—05 INST ALLATION VERIFY the input voltage rating and configu ration on the unit panel label to ensure it is suitable for the intended e lectrical servic e. Meters labeled for 1 15/208 volt service MUST NOT be installed on service feeds of 277/4 80 volt and vice versa. VERIFY that the Class 500 Meter c ...

  • Honeywell 500 - page 4

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 4 Main Power Board Connections to this board include the MA INS input voltage, current sensors, an d external pulse input (See Fig. 2). The MAINS input terminals are covered with a protective clear sh ield fo r safety purposes. The current sensor assemblies interface to TB2, TB3 or TB4. Each header ...

  • Honeywell 500 - page 5

    CLASS 500 ADVANCED KWH/DEMAND METER 5 62-0304—05 d. Connect the three AC mains power wires (PHASE A, PHASE B, and PHASE C) to their respective po sitions as labeled on terminal block TB1. After all conductors are connected to their respective terminal block positions and tightened down, verify each terminal block screw is securely fastene d by ge ...

  • Honeywell 500 - page 6

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 6 Fig. 3. Split core current sensor assembly . Fig. 4. Split core current sensor assembl y installed. IMPORT ANT : When looking from the source side of the conductor(s) bein g monitored, you should see the arrow on the current sensor assembly . The arrow should be pointing in a clockwise direct ion ...

  • Honeywell 500 - page 7

    CLASS 500 ADVANCED KWH/DEMAND METER 7 62-0304—05 Fig. 7. Location of LED D5 (lab eled “MTR”) and Ethernet board. V erify that the AC MAINS vol tage wires ar e all connected to the correct posi tions on terminal block TB1. Inspect the MAINS inp u t wiring to verify each conductor is terminated at the correct te rminal block positi on. Using an ...

  • Honeywell 500 - page 8

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 8 Wiring to the Network RS-485 Wiring for BACnet MS/T P , Modbus RTU, or EZ-7 The Class 500 Meter contains an RS-485 serial communications port allowing it to commu nicate via BACnet MS/TP , Modbus RTU, or EZ-7. The units can be daisy-chained together over dist ances of up to 4000 fe et. Up to 52 un ...

  • Honeywell 500 - page 9

    CLASS 500 ADVANCED KWH/DEMAND METER 9 62-0304—05 The meter is shipped with a Modb us ID number of 01. This must be changed if the network has more than one meter installed. The change must be do ne before the meter is in troduced i nto the network, or it can b e put on the network as the only device on the network and Modbus address cha nged befo ...

  • Honeywell 500 - page 10

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 10 Fig. 1 1. LON wiring . Ethernet wiring for BACnet IP , an d Modbus TCP/IP and Ethernet EZ-7 These models are shipped with a board that a llows for Ethernet commun ication via Modb us TCP/IP , BACnet IP or Ethernet EZ-7. EZ-7 protocol is required when using the En ergy Software. Modbus TCP/IP and ...

  • Honeywell 500 - page 11

    CLASS 500 ADVANCED KWH/DEMAND METER 11 62-0304—05 NOTE: One set of current sensors equates to th ree sensors, one per phase. The multiplier only appli es when extra sets of cur- rent sensors are installed on one Class 50 0 Meter . Therefore, if you are using on ly one set of three current sensors, the multiplier is not required. Fig. 12. Parallel ...

  • Honeywell 500 - page 12

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 12 MAINTENANCE The Class 500 Meter unit is shi pped in a calibrated an d fully fu nctionally tested condi tion. Sinc e the u nit is factory calibrat ed using proprietary firmware algorithms, no internal uni t adjustments ar e nece ssary . Th is unit contains no internal adjustments. Theref ore no pr ...

  • Honeywell 500 - page 13

    CLASS 500 ADVANCED KWH/DEMAND METER 13 62-0304—05 Use the following procedure to re place the lithium battery cell. 1. Disconnect power from the Class 500 Meter at the unit external circuit breaker . 2. Remove the battery from its socket and place it on a non-conductive surface. 3. Install the new battery into the PCB battery socket. NOTE: The ma ...

  • Honeywell 500 - page 14

    CLASS 500 ADVANCED KWH/DEMAND METER 62-0304—0 5 14 Modbus Point Map Modbus data points available from the Class 5 00 meter . Listed under Class 500. T able 4. Honeywell Mod bus point map INTEGER W FLOA T UOM CALC. MEM OP DESCRIPTION CLASS 500 1 40001 2 41001 kWh T-del NV R/W Energy delivered Y 2 40003 2 41003 kWh T-rec NV R/W Energy received Y 3 ...

  • Honeywell 500 - page 15

    CLASS 500 ADVANCED KWH/DEMAND METER 15 62-0304—05 NOTE: T o change device ID, set single point at 46049 with data set to new device ID (e.g., 1 to 247). T o set date/time, set multiple points at 46025 for 4 points with data set to HHMM SSDW MMDD YYYY (DW=day of week). T o clear single meter kWh/kW , set single point at 41001 wi th data set to 000 ...

  • Honeywell 500 - page 16

    CLASS 500 ADVANCED KWH/DEMAND METER Automation and Co ntrol Solutions Honeywell Internationa l Inc. 1985 Douglas Drive North Golden Valley, MN 55422 customer.honeywell.com ® U.S. Regi stered T rademark © 201 1 Ho neywell International Inc. 62-0304—05 M .S. Rev . 06-1 1 Printed in U.S. A. FREQUENTLY ASKED QUESTIONS Q. When provid ing line voltag ...

メーカー Honeywell カテゴリー Automobile Parts

Honeywell 500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 500の取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell 500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell 500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell 500の取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell 500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell 500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell 500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell 500を使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell 500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell 500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell 500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell 500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell 500デバイスの基本機能を使うにあたってのヒント。 Honeywell 500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell 500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell 500のメーカー/サービスへの連絡先に関する情報。

Honeywell 500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell 500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell 500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)