日本語 dropdown-ico

Dolmar MS-230 Cの取扱説明書

24ページ 1.4 mb
ダウンロード

ページに移動 of 24

Summary
  • Dolmar MS-230 C - page 1

    Important: Read this instruction manual carefully before putting the brushcutter into operation and strictly observe the safety regulations! Keep this Instruction Manual! Instruction Manual http://www .dolmar .com MS-260 U MS-330 U MS-430 U MS-230 C MS-260 C MS-330 C ...

  • Dolmar MS-230 C - page 2

    2 T able of contents Page EC declaration of conformity ............................................ 2 Packing ................................................................................ 2 Delivery inventory .............................................................. 3 Explanation of symbols .................................................. ...

  • Dolmar MS-230 C - page 3

    3 12 Shown: MS-260 U STOP Read the instruction manual and follow all warnings and safety instructions! Particular care and caution! Forbidden! Wear protective gloves! Wear safety shoes! Wear head, eye, face and hearing protec - tion! The distance between the machine and bystanders shall be at least 50 feet! DANGER: Beware of thrown objects! Do not ...

  • Dolmar MS-230 C - page 4

    4 SAFETY PRECAUTIONS General precautions Proper use: These power brushcutters are intended for cutting grass or heavy weeds, with the appropriate and permissible cut- ting tools. A brushcutter may be operated only by one person, and only out of doors! Improper use: The cutting tools permissible for this brushcutter must not be used to cut heavier m ...

  • Dolmar MS-230 C - page 5

    5 - Ensure that no fuel or chain oil oozes into the soil (environ mental protection). Use an appropriate base. - Refuelling is not allowed in closed rooms. Fuel vapors will accumulateneartheoor(explosionhazard). - Carefully tighten the locking screw of the fuel tank and inspect the fuel cap at regular intervals. - Change the place ...

  • Dolmar MS-230 C - page 6

    6 14 15 1 1 12 13 Kickback During operation the brushcutter can kickback in an uncon- trolled manner . This can happen when the cutting blade (4- tooth star blade) comes into contact with hard objects such as stumps, fenceposts, tree trunks, woody brush or large rocks. This can ing the brushcutter to one side with great force and speed (injury h ...

  • Dolmar MS-230 C - page 7

    7 Storage - The brushcutter must be safely stored in a dry room. Use the tool protection for metal cutting tools. Keep the brushcutter out of reach of children. - If the brushcutter is stored for a long period of time, it should be given a thorou gh mainte nance check and a complete inspection at an authorized DOLMAR service centre. - If the brushc ...

  • Dolmar MS-230 C - page 8

    8 1) The maximum rated speed of the trimmer head is not exceeded when using a DOLMAR trimmer head. 2) Figures derived in equal part from idle and top-speed operation (per EN-ISO 1 1806). 3) At max. power T echnical Data 230 C | 260 C | 330 C Displacement cm 3 22.6 | 25.6 | 32.6 25.6 | 32.6 | 42.7 Bore mm 31 | 33 | 36 33 | 36 | 40 Stroke mm 30 | 30 ...

  • Dolmar MS-230 C - page 9

    9 PUTTING INTO OPERA TION ST OP CAUTION: When working on the brushcutter always be absolutely certain to switch off the engine, pull the spark plug cap and wear protective gloves! IMPORT ANT : Do not start the brushcutter until fully assembled and inspected! A - Loosen screws ( A/1 ) and unscrew about 1-2 mm. - Push the grips ( A/2 ) into the grip ...

  • Dolmar MS-230 C - page 10

    10 6 7 8 Installing the cutter guard Cutting tool Cutter guard T ool/guard combinations for the MS-260 U / MS-330 U / MS-430 U A 4-tooth star blade: Part no. 362 224 140 Part no. 351 504 101 O ut si d e di a me te r : 23 0 m m ( 9" ), ar b o ur : 2 5, 4 m m ( 1" ) 2-line trimmer head Part no. 351 502 030 Part no. 351 504 101 15 m Part no. ...

  • Dolmar MS-230 C - page 11

    1 1 C - Removeoatingdisc( C/6 ) and thrust washer ( C/5 ). - Insert the offset screwdriver 4 mm ( C/1 ) through the wind- ing guard and the locking disc into the opening ( C/3 ) in the angular gear (block the winding gear). If necessary turn the mounting disc ( C/3 ) slightly . - Position the blade ( C/4 ), thrust washer ( C/5 ) a ...

  • Dolmar MS-230 C - page 12

    12 F Replacing the line - Y ou can adjus t the li ne to th e right lengt h at any ti me by lig htly tapping the trimmer head against the ground (direction of arrow). The line cutter automatically cuts of f excess line. However , this only works when at least 3 cm of line are vis - ible at each end. - If the line ends are shorter than 3 cm, it will ...

  • Dolmar MS-230 C - page 13

    13 A VOID SKIN AND EYE CONT ACT! Utmost care is required when handling fuel. Fuel may contain substances similar to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel vapours. Fuel vapours are poisonous and can be hazardous to your health. Avoid eye and skin contact with fuels and mineral oils. Mineral oil products de ...

  • Dolmar MS-230 C - page 14

    14 Putting on the harness - Putontheharnessasshowningure A. - Adjust it so that the clip is about a hand-width above your hipbone. A B - Correctly balancing the brushcutter reduces strain on the arms while working. - When using the trimmer head on a level terrain, the trimmer head should touch the ground lightly without t ...

  • Dolmar MS-230 C - page 15

    15 Cold start F - Prime the fuel pump ( G/5 ) by pressing it several times until you can see fuel in the pump. - Actuate the half-throttle lock by depressing the safety lock ( F/3 ), pressing in the throttle ( F/1 ) and moving the combi- nation switch ( F/2 ) into the ST ART position. Then release throttle ( F/1 ) and then the combination switch ( ...

  • Dolmar MS-230 C - page 16

    16 REP AIR AND MAINTENANCE WORK CAUTION: Before doing any work on the brushcutter , always switch off the motor and pull the plug cap off the spark plug . Always wear protective gloves! CAUTION: Start the brushcutter only after complete assembly and inspection! General The brushcutter Clean exterior , check for damage. In case of damage,  asa ...

  • Dolmar MS-230 C - page 17

    17 Cleaning the air lter - Loosen the screws ( A/1 ) and rem ove the air lter cover  ( A/2 ). - T akethefoamlteroutofthecover . Caution: T o prevent eye injuries, do not blow out dirt particles! - V ery dirty lters can be cleaned out using regular dishwash - i ...

  • Dolmar MS-230 C - page 18

    18 T rouble shooting After about 50 operating hours the gear box ( D/8 ) should be checked by a OLMAR service centre, and if necessary re- grease. The service centre will add the exact amount of grease, as excessive grease will lead to overheating of the gearbox. Lubricating the gear box Thefelt lter( E/9 ) of thesuction hea ...

  • Dolmar MS-230 C - page 19

    19 Service, spare parts and guarantee Maintenance and repair The maintenance and repair modern brushcutters and safety-related components and assemblies requires qualied technical training and a workshop equipped with special tools and testing devices. Any maintenance or adjustment work not described ...

  • Dolmar MS-230 C - page 20

    20 Guarantee DOLMAR guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular guarantee conditions may exist. If you have any questions, please contac ...

  • Dolmar MS-230 C - page 21

    21 Notes ...

  • Dolmar MS-230 C - page 22

    22 Notes ...

  • Dolmar MS-230 C - page 23

    23 Notes ...

  • Dolmar MS-230 C - page 24

    Form: 995 703 482 (10.06 GB) Specicationssubjecttochangewithoutnotice DOLMAR GmbH Postfach 70 04 20 D-22004 Hamburg Germany http://www .dolmar .com T ondyourlocaldistributor , please visit www .dolmar .com ...

メーカー Dolmar カテゴリー Brush Cutter

Dolmar MS-230 Cのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MS-230 Cの取扱説明書
- Dolmarの製品カード
- パンフレット
- またはDolmar MS-230 Cの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Dolmar MS-230 Cの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Dolmar MS-230 Cの取り付け説明書、サービスマニュアル、簡易説明書、またはDolmar MS-230 Cのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Dolmar MS-230 Cの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Dolmar MS-230 Cデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDolmar MS-230 Cを使用するのを助ける技術的文書のことです。説明書は通常、全てのDolmar MS-230 Cユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Dolmarの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Dolmar MS-230 Cの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDolmar MS-230 Cの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Dolmar MS-230 Cに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Dolmar MS-230 Cデバイスの基本機能を使うにあたってのヒント。 Dolmar MS-230 Cのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Dolmar MS-230 Cに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDolmar MS-230 Cのメーカー/サービスへの連絡先に関する情報。

Dolmar MS-230 Cについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもDolmar MS-230 Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDolmar MS-230 Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)