-
Makita 1001 - page 1
Curved Planer Planing width 82 mm 13~114") 82 mm (3-1/4") MODEL 1001 Planing depth No load speed Overall length Net weight 3 mm 1118"l 12,000 370 mm 1,14~1/2"1 6.0 kg 113.2 lbsl IRPMI INSTRUCTION MANUAL ...
-
Makita 1001 - page 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, includ- ing the following: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 14. 15. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. ...
-
Makita 1001 - page 3
17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of ...
-
Makita 1001 - page 4
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Keep ...
-
Makita 1001 - page 5
Removing or installing planer blades WARNING : Always be sure that the tool is switched off and unplugged before removing or installing the blades. To remove the blades on the drum, un- screw the three installation bolts with the socket wrench. The drum cover comes off together with the blades. To install the blades, first clean out all chips or fo ...
-
Makita 1001 - page 6
Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Adjusting front base 1. To create a curved surface, loosen the wing nut. For a concave planing job, raise the front base; for a convex plan- ing job, lower the front base. In either case, the front base must be aligned with the cutting line. The ...
-
Makita 1001 - page 7
2. To create a flat surface, loosen the wing I nut after setting the tool on a level sur- face. Turn the front knob on the tool until the front base is perfectly level with the rear base. Then tighten the wing nut securely. Wing nut F Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pu ...
-
Makita 1001 - page 8
NOTE : I *When beginning the planing of a flat shape, first take down the middle of the workpiece, gradually planing until the ultimate concave shape is achieved. workpiece to obtain eventually a concave First take down both ends of the workpiece *When beginning the planing of a flat workpiece to obtain eventually a convex shape, first take down bo ...
-
Makita 1001 - page 9
Sharpening planer blades Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides (C) and (D). Then tighten the wing nuts. Immerse the dressing stone in water for ...
-
Makita 1001 - page 10
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r ...
-
Makita 1001 - page 11
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade Width : 82 mm (3-1/4") Part ...
-
Makita 1001 - page 12
Jan 26-89 EN 82 mm (3-1/4") CURVED PLANER Model 1001 Note The switch, noise suppressor and other part configuratlons may differ from country to country 12 ...
-
Makita 1001 - page 13
MODEL 1001 z:, DESCRIPTION ITEM NO NO USED MACHINE ~ 1 2 3 4 5 6 1 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 31 32 4 1 1 1 1 1 1 2 1 1 1 6 2 4 2 1 1 1 I 2 1 1 2 I 2 2 4 1 1 1 1 1 - Pan Head Screw M5x25 IWith Washer1 Bracket Ball Bearing 6200LLB Fan 80 ARMATURE ASSEMBLY !With lfem 3 71 Flaf Washer 12 Ball Bearing 6201LLB Pan ...
-
Makita 1001 - page 14
14 ...
-
Makita 1001 - page 15
...
-
Makita 1001 - page 16
Makita Corporation 3-11 -8, Sumiyoshi-cho, Anjo, Aichi 446 Japan 883000A0 PRINTED IN JAPAN I991 -1 0 E ...
Makita 1001についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもMakita 1001の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita 1001で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。