-
Polycom MD4000 - page 1
June 2008 Edition 1725-36164-001 Version B VIEW Certified Configuration Guide MeshDynamics MD4000 Series APs ...
-
Polycom MD4000 - page 2
Configuration Guide PN: 1725-36164-001_B.doc 2 Trademark Information Polycom® and t he logo design s SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registe red trademarks of Polycom, Inc. in the Un ited States of Am erica and various c ountries. All ot her trademarks used herein are the propert y of their respective owners. Patent Info ...
-
Polycom MD4000 - page 3
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 3 Introduction Polycom’s Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink Wireless Telephones and WLAN infrastructure products. The products listed below have been thoroughly tested in Po ...
-
Polycom MD4000 - page 4
Configuration Guide PN: 1725-36164-001_B.doc 4 Monday through Friday, 6 a.m. to 6 p.m. Mountain time. You may also contact Polycom Technical Support at boul-technicalsupport@polycom.com for assistance. Network Topology The following topology was tested during VIEW Certification testing. SpectraLink Wireless Telephones ...
-
Polycom MD4000 - page 5
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 5 Initial Configuration Settings Network Management System (NMS) is required to configure the access point. 1. Download http://www.meshdynamics.com/downloads/MDNetworkView er82.exe from www.meshdynamics.com 2. The NMS must run from a machine on the same network . 3. The NMS requires Java 1.4 Run ...
-
Polycom MD4000 - page 6
Configuration Guide PN: 1725-36164-001_B.doc 6 Configuration Settings The settings listed below are recommended for interoperability and high performance between SpectraLink Wireless Telephones and the MeshDynamics Wireless LAN System. ...
-
Polycom MD4000 - page 7
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 7 Configuring Interfaces 1. Right-click the access point icon (Node). 2. Select Configure Node from the shortcut menu to begin configuration. 3. Click the Interfaces tab in the Node Configuration window. 4. Select the appropriate radio interface: a. Click the 5G Down Link option if the SpectraLi ...
-
Polycom MD4000 - page 8
Configuration Guide PN: 1725-36164-001_B.doc 8 5. Enter the ESSID to match the SpectraLink Wireless Telephones. 6. Adjust the Power Le vel Setti ng and Dynamic Channel Management setting for appropriate level/channel as determined by your facility site survey, optimized for wireless voice traffic. If Dynamic Channel Management is set to Auto , the ...
-
Polycom MD4000 - page 9
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 9 c. If SpectraLink Wireless Telephones are configured for 802.11g only, select the 11g check box for 2.4G Mode . All rates are set as basic rates; multicast traffic will be transmitted at the lowest basic rate for each band (1Mb/s for 802.11b, 6Mb/s for 802.11g, and 6Mb/s for 802.11a). ...
-
Polycom MD4000 - page 10
Configuration Guide PN: 1725-36164-001_B.doc 10 QOS Settings 1. Click the VLAN tab in the Node Configuration window. 2. To adjust QoS settings, click the “New VLAN” icon. 3. Click the “ … ” button to the far right of 802.11e Category to edit the 802.11e category for that Node. 4. Select Voice from the 802.11e Access Categ ory drop-down li ...
-
Polycom MD4000 - page 11
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 11 Security Settings WPA2-PSK setup 1. Click the Security tab in the Node Configuration window. 2. Click the WPA Personal option. 3. At Mode , select WPA2/802.11i from the drop-down list. 4. Enter a Passphrase that matches the entry on the SpectraLink Wireless Telephones. 5. Click the Save butto ...
-
Polycom MD4000 - page 12
Configuration Guide PN: 1725-36164-001_B.doc 12 Effistream™ Settings Effistream allows setting packet-based policies for QoS. Effistream is set so that the access point can serve SVP Packet s more efficiently. 1. Click the Effistream tab in the Nod e Configuration window. 2. Click the Add Rules button. 3. In the Rule Properties dialog box: a. Let ...
-
Polycom MD4000 - page 13
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 13 4. Select the previous rule ( Ethernet Type … ). 5. Click the Add Rule button. 6. In the Rule Properties dialog box: a. Let Criteria be IP Protocol . b. In the Protocol field, type 119 . c. Click the Save button. ...
-
Polycom MD4000 - page 14
Configuration Guide PN: 1725-36164-001_B.doc 14 7. Under Rules , select IP Protocol=119 . 8. Click the Add Action button. 9. In the Action Properties dialog box: a. Select the Queued Retry check box. b. Set Transmit Rate as 0 (Auto) . c. Set 802.11e Category as Voice . d. Click the Save button to update the Node. 10. Reboot the Node for settings to ...
-
Polycom MD4000 - page 15
MeshDynamics 4000 Series APs PN: 1725-36164-001_B.doc 15 Further Assistance For additional details on NMS installation and configuration, see http://www.meshdynamics.com/documents/MD4000_NMSGUIDE. pdf or contact http://www.meshdynamics.com for support. ...
Polycom MD4000についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもPolycom MD4000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPolycom MD4000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。