Tripp Lite SmartPro 450 RTIの取扱説明書

32ページ 0.87 mb
ダウンロード

ページに移動 of 32

Summary
  • Tripp Lite SmartPro 450 RTI - page 1

    Installation: p . 3 Basic Operation: p. 5 Storage & Service: p. 8 Specifications: p . 8 Safety: p . 2 W arranty & Insurance: p. 9 - 10 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: +1 (773) 869-1234 www.tripplite.com Owner's Manual Smar tPr o ® 450 R TI Rac kmount/T ower Intelligent Network UPS System (230V) ESP AÑOL: p ...

  • Tripp Lite SmartPro 450 RTI - page 2

    This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite UP S Systems. UPS Location W arnings • Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight. • For best performance, keep the indoor temperature between 0° C and 40° ...

  • Tripp Lite SmartPro 450 RTI - page 3

    Mounting Note: When removing the mounting bracket screws to change the mounting profile of your UPS, do not remove the screws which secure the UPS cabinet. Two of these screws are located at each end of the UPS, between the four holes used for the mounting brackets. Rackmount Your UPS’s mounting brackets are pre-set at a standard depth for 48 cm. ...

  • Tripp Lite SmartPro 450 RTI - page 4

    Connect your computer to the UPS, and the UPS to an electrical outlet. 1 . Unplug your computer’s power cord from both your AC outlet and your computer’s AC input. 2. Insert the female plug of the power cord that came with your UPS (A) into your computer’s AC input. Insert the UPS cord’s male plug into any of your UPS’s female output rece ...

  • Tripp Lite SmartPro 450 RTI - page 5

    Basic Operation 2 3 4 5 7 8 11 13 9 10 6 Front Back 12 1 10 Switch 1. Main Power Switch This switch activates three separate UPS functions: UPS Power Press the switch, hold it for 3 seconds until you hear a beep then release it during the beep to turn the UPS ON or OFF.* Alarm Silence When the on battery alarm is sounding, press this switch and imm ...

  • Tripp Lite SmartPro 450 RTI - page 6

    Indicator Lights The SmartPro 450 RTI uses dual function Indicator Lights. These lights can indicate more than one UPS or power condition, depending on whether they illuminate constantly or flash. All Indicator Light descriptions refer to when the UPS is connected to the wall outlet and turned ON. 2. "A C Normal/A VR" LED This green light ...

  • Tripp Lite SmartPro 450 RTI - page 7

    Other UPS Features 6. AC Receptacles (Battery Backup-Supported) These receptacles provide your connected equipment with AC line power during normal operation and battery power during blackouts and brownouts. They also protect your equipment against damaging surges and line noise. Connect com- puter, monitor and other essential equipment to these re ...

  • Tripp Lite SmartPro 450 RTI - page 8

    Specifications Storage & Service Storage First turn your UPS OFF and disconnect its power cord from the wall outlet. Then disconnect all equipment to avoid battery drain. If you plan to store your UPS for an extended period of time, fully recharge the UPS batteries once every three months by plugging the UPS into a live AC outlet, turning the P ...

  • Tripp Lite SmartPro 450 RTI - page 9

    Instalación p . 1 1 Operación Básica: p. 13 Servicio de Reparaciones: p. 16 Especificaciones: p . 1 6 Seguridad: p . 1 0 W arranty & Insurance: p. 9 - 10 1111 W. 35th Street Chicago, IL 60609 USA Servicios a Clientes:+1 (773) 869-1234 www.tripplite.com Manual de Operaci ó n Smar tPr o ® 450 R TI Instalaci ó n en Bastidores para Redes (230 ...

  • Tripp Lite SmartPro 450 RTI - page 10

    Seguridad Este manual contiene advertencias e instrucciones importantes que deben seguirse durante la instalación, operación y almacenaje de todos los Sistemas UPS Tripp Lite. Advertencias sobre la Ubicaci ó n del Sistemas UPS • Instale este sistema UPS bajo techo, lejos de calor y humedad excesiva, polvo o luz solar directa. • Para obtener ...

  • Tripp Lite SmartPro 450 RTI - page 11

    Instalaci ó n Figure 1 – Torre Vertical Figure 2 – Un sistema UPS instalado en la pared Figure 3 – Dos sistemas UPS instalados en la pared Importante: Al remover los tornillos de los soportes de fijación para ajustar el perfil de montaje del sistema UPS no remueva los tornillos que aseguran el gabinete del sistema UPS. Dos de estos tornillo ...

  • Tripp Lite SmartPro 450 RTI - page 12

    UPS OUTLER MAX LOAD 450VA 270w SURGE ONL Y Conecte su impresora u otro tipode equipo perif é rico al recept á culo conprotecci ó n contrasobretensiones ú nicamente ( “ Surge-Only Receptacle ” ). - Opcional – Utilizando el cable suministrado por Tripp Lite, conecte el puerto serial de su computadora al puerto serial del sistema UPS. ** Ins ...

  • Tripp Lite SmartPro 450 RTI - page 13

    Operaci ó n B á sica 2 3 4 5 7 8 11 13 9 10 6 Vista Posterior 12 1 10 Interruptor 1. Interruptor “ Main P o wer Switc h ” (interruptor principal) Este interruptor activa tres funciones separadas del sistema UPS: Encendido y Apagado Presione este interruptor, sosténgalo por 3 segundos hasta que se escuche un leve sonido (bip). Suéltelo duran ...

  • Tripp Lite SmartPro 450 RTI - page 14

    El modelo SmartPro 450 RTI utiliza Luces Indicadoras de funciones dobles que le alertan acerca de situaciones diferentes de operación de acuerdo con la forma de iluminación (iluminadas constantemente o parpadeando). Todas las descripciones de las Luces Indicadoras son válidas mientras el sistema UPS esté encendido (“ON”) y conectado a una t ...

  • Tripp Lite SmartPro 450 RTI - page 15

    6. Recept á culos de CA Respaldados por las Bater í as: Estos receptáculos suministran energía de CA a los equipos conectados bajo condiciones normales de operación y energía de batería durante apagones y caídas de voltaje. También protegen sus equipos contra peligrosas sobretensiones y ruidos de línea. Conecte su computadora, monitor y o ...

  • Tripp Lite SmartPro 450 RTI - page 16

    Marrón Azul Verde/ Amarillo Negro Blanco Verde Especificaciones Almacenaje y Servicio Almacenaje Almacenaje y ServicioPrimero apague (“OFF”) el sistema UPS y desconecte su cable de conexión de la toma eléctrica. Después desconecte todos los equipos para evitar el desgaste de las baterías. Si usted desea almacenar el sistema UPS por un per? ...

  • Tripp Lite SmartPro 450 RTI - page 17

    Installation: p . 1 9 Opération de base: p. 21 Entreposage & Service: p. 24 Caractéristiques: p . 2 4 Sûreté: p . 18 W arranty & Insurance: p. 9 - 10 1111 W. 35th Street Chicago, IL 60609 USA Servicios a Clientes:+1 (773) 869-1234 www.tripplite.com Manuel de l ’ Utilisateur Smar tPr o ® 450 R TI Onduleur de R é seau Intelligent (230 ...

  • Tripp Lite SmartPro 450 RTI - page 18

    S û ret é : Ce manuel contient des instructions et recommandations importantes qui doivent être suivies durant l’installation, l’opération et l’entreposage de tous les onduleurs de Tripp Lite. Recommandations relatives à l ’ Emplacement de l ’ Onduleur • Installez votre onduleur à l’intérieur, loin de l’humidité excessive ou ...

  • Tripp Lite SmartPro 450 RTI - page 19

    Installation Sch é ma # 1 – Tour Verticale Sch é ma # 2 – Montage Mural d ’ Un Onduleur Sch é ma # 3 - Montage Mural de Deux Onduleurs Montage Note: En retirant les vis de support pour changer le profil de support de votre onduleur, ne retirez pas les vis qui fixent le module de l’onduleur. Deux de ces vis sont placées à chaque extrém ...

  • Tripp Lite SmartPro 450 RTI - page 20

    3 2 1 Connexion UPS OUTLER MAX LOAD 450VA 270w SURGE ONL Y Branchez votre ordinateur à l ’ onduleur , et l ’ onduleur à une prise é lectrique. 1 . D é branchez le cordon d ’ alimentation de votre ordinateur à partir de la sortie C.A. et de l ’ entr é e C.A. de votre ordinateur. 2. Ins é rez la prise femelle du cordon d ’ alimentati ...

  • Tripp Lite SmartPro 450 RTI - page 21

    Op é ration de base 2 3 4 5 7 8 11 13 9 10 6 Face Avant Face Arri è 12 1 10 Commutateur 1. Commutateur Principal d ’ Alimentation Ce commutateur active trois fonctions séparées de l’onduleur: Alimentation de l’Onduleur Pressez le commutateur, retenez le pendant 3 secondes jusqu’à ce que vous entendiez un signal sonore puis libérez le ...

  • Tripp Lite SmartPro 450 RTI - page 22

    V o y ants de Signalisation Le SmartPro 450 RTI utilise une double fonction de Voyants de Signalisation. Ces Voyants vous indiquent plus d’une condition de l’alimentation ou de l’onduleur, à savoir s’ils s’allument en permanence ou s’ils clignotent. Toutes les descriptions du Voyant de Signalisation s’appliquent lorsque l’onduleur ...

  • Tripp Lite SmartPro 450 RTI - page 23

    A utres Caracteristiques de L ’ onduleur 6. R é ceptacles C.A. (Support Sauvegarde Batterie) Ces réceptacles fournissent à votre matériel relié à l’alimentation de ligne C.A. pendant l’exécution normale et l’alimentation de la batterie pendant des arrêts totaux et des arrêts partiels d’alimentation. Ils protègent également votr ...

  • Tripp Lite SmartPro 450 RTI - page 24

    Caracteristiques Entreposage & Service Entreposage Positionnez tout d’abord votre onduleur sur OFF et déconnectez son cordon d’alimentation de la prise murale. Débranchez ensuite tout le matériel pour éviter l’écoulement de la batterie. Si vous envisagez d’entreposer votre onduleur pendant une longue période, veuillez recharger en ...

  • Tripp Lite SmartPro 450 RTI - page 25

    Installation: S . 2 7 Bedienung: S . 2 9 La gerung und W ar tung: S. 32 T echnisc he Merkmale: S. 32 Sicherheit: S . 26 W arranty & Insurance: p. 9 - 10 1111 W. 35th Street Chicago, IL 60609 USA Kundendienst: 1 (773) 869-1234-9764 www.tripplite.com Besitzerhandbuch Smar tPr o ® 450 R TI Intellig ente Netzwerk-USV -Systeme (230 V) Gestellaufbau ...

  • Tripp Lite SmartPro 450 RTI - page 26

    Sicherheit Dieses Handbuch enthält wichtige Anweisungen und Warnungen, die bei der Installation, dem Betrieb und der Lagerung aller USV-Systeme zu beachten sind. W arnung: Standor t der USV • Installieren Sie Ihre USV im Rauminnern, an einem trockenen, hitzegeschützten, staubfreien Ort ohne direkte Sonneneinstrahlung. • Halten Sie die Raumtem ...

  • Tripp Lite SmartPro 450 RTI - page 27

    Installation Abbildung 1 – Vertikaler Turm Abbildung 2 – Wandaufbau Eine USV Abbildung 3 – Wandaufbau Zwei USV Montage Anmerkung: Wenn Sie Befestigungshalterungsschrauben entfernen, um das Befestigungsprofil Ihrer USV abzuändern, dürfen Sie keine Schrauben entfernen, mit denen das USV-Gehäuse befestigt ist. Je zwei dieser Schrauben befinde ...

  • Tripp Lite SmartPro 450 RTI - page 28

    Schließen Sie Ihren Com- puter an Ihre USV und die USV an eine Netzsteckdose an. 1. Ziehen Sie das Netzkabel des Computers aus der Wechselstrom (AC)-Steckdose und aus der computerseitigen (AC)-Eingangsbuchse. 2. Stecken Sie den Mutterstecker des Netzkabels, das mit Ihrer USV geliefert wurde, in die AC-Eingangsbuchse Ihres Computers. Stecken Sie de ...

  • Tripp Lite SmartPro 450 RTI - page 29

    Bedienung 2 3 4 5 7 8 11 13 9 10 6 Vorderseite Rückseite 12 1 10 Schalter 1. Hauptschalter Dieser Schalter aktiviert drei verschiedene USV-Funktionen: Einschalten der USV Drücken Sie den Schalter drei Sekunden lang bis Sie einen Pfeifton hören und lassen ihn dann los, wenn Sie die USV ein- bzw. ausschalten möchten.* Geräuschlosstellen des Alar ...

  • Tripp Lite SmartPro 450 RTI - page 30

    K ontr olllichter Die Power Pro 450 T verwendet Dualfunktions-Kontrollichter. D.h. durch dauerndes Leuchten oder Aufblinken werden Ihnen verschiedene Betriebszustände der USV oder der Stromversorgung gemeldet. Alle Kontrolllichtbeschreibungen gelten für eine in eine Wandsteckdose eingesteckte und eingeschaltete USV. 2. W ec hselstr om Normal/A VR ...

  • Tripp Lite SmartPro 450 RTI - page 31

    W eitere USV -A usrüstung en 6. A C-Buc hsen (Batterie Bac kup-unter stützt) Diese Buchsen versorgen Ihre angeschlossenen Geräte bei normalem Betrieb mit Wechselstrom (AC) aus dem Netz und bei Stromausfällen und Netzspannungsabsenkungen mit Batteriestrom. Sie schützen Ihre Geräte auch gegen schädigende Spannungsstöße und Netzstörungen. Sc ...

  • Tripp Lite SmartPro 450 RTI - page 32

    T echnisc he Merkmale La g erung und W ar tung 93-1561 (200002079) 04/00 Lagerung Schalten Sie erst Ihre USV aus (OFF) und ziehen Sie den Netzstecker aus der Steckdose an der Wand. Stecken Sie dann alle Ausrüstungen aus, um ein Entladen der Batterie zu vermeiden. Wenn Sie vorhaben, Ihre USV über längere Zeit zu lagern, dann laden Sie die Batteri ...

メーカー Tripp Lite カテゴリー Power Supply

Tripp Lite SmartPro 450 RTIのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SmartPro 450 RTIの取扱説明書
- Tripp Liteの製品カード
- パンフレット
- またはTripp Lite SmartPro 450 RTIの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Tripp Lite SmartPro 450 RTIの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Tripp Lite SmartPro 450 RTIの取り付け説明書、サービスマニュアル、簡易説明書、またはTripp Lite SmartPro 450 RTIのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Tripp Lite SmartPro 450 RTIの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Tripp Lite SmartPro 450 RTIデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTripp Lite SmartPro 450 RTIを使用するのを助ける技術的文書のことです。説明書は通常、全てのTripp Lite SmartPro 450 RTIユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Tripp Liteの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Tripp Lite SmartPro 450 RTIの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTripp Lite SmartPro 450 RTIの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Tripp Lite SmartPro 450 RTIに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Tripp Lite SmartPro 450 RTIデバイスの基本機能を使うにあたってのヒント。 Tripp Lite SmartPro 450 RTIのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Tripp Lite SmartPro 450 RTIに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTripp Lite SmartPro 450 RTIのメーカー/サービスへの連絡先に関する情報。

Tripp Lite SmartPro 450 RTIについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもTripp Lite SmartPro 450 RTIの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTripp Lite SmartPro 450 RTIで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)