Shindaiwa DH254の取扱説明書

28ページ 1.64 mb
ダウンロード

ページに移動 of 28

Summary
  • Shindaiwa DH254 - page 1

    SHIND AIWA OWNER’S/OPERA T OR’S MANU AL DH254 HEDGE TRIMMER Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hear- ing protection when operating this unit. WARNING! X7502864301 06/10 ...

  • Shindaiwa DH254 - page 2

    2 Attention Statements WARNING! A statement preceded by the triangu- lar Attention Symbol and the word "W ARNING" contains information that should be acted upon to prevent serious bodily injury . IMPORT ANT! The operational procedures described in this manual are intended to help you get the most from your unit, and to pro- tect you and o ...

  • Shindaiwa DH254 - page 3

    3 WARNING! Minimize the Risk of Fire! AL W A Y S check unit for fuel leaks before use. Check for leaks around fuel tank cap while refueling. If fuel leaks are found immediately stop using the unit. Fuel leaks must be repaired before using unit. AL W A YS move the unit to a place well away from a fuel storage area or other readily ammable materia ...

  • Shindaiwa DH254 - page 4

    4 WARNING! Inspect front and rear handles for damaged or loose attachments before use. NEVER operate a hedge trimmer with damaged or loose handles. Operating Precautions WARNING! Never transport the hedge trim- ■ mer or leave it unattended with the engine running. An engine that’s running could be accidently acceler- ated causing the blades to ...

  • Shindaiwa DH254 - page 5

    5 Safety Equipment and Labels IMPORT ANT! Caution, Danger , W arning, and Operation Information Labels: Make sure all information labels are undam- aged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer . Figure 2 Ignition Switch Throttle Interlock Caution L ...

  • Shindaiwa DH254 - page 6

    6 An Emission Control Label is located on the unit. (This is an EXAMPLE ONL Y ; information on label varies by en - gine F AMIL Y). PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD) The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulatio ...

  • Shindaiwa DH254 - page 7

    7 Blade Stiffener Removal Move stop switch to stop position. 1. Disconnect spark plug wire. 2. W ARNING! Hedge clipper blades are very sharp. T ouching them may lead to severe personal injury . Use a socket and extension when removing locknuts in order to keep hands at a safe distance from sharp blades. Remove seven (7) blade stif fener locknuts (A ...

  • Shindaiwa DH254 - page 8

    8 WARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause performance problems, loss of power , overheating, fuel vapor lock, and unintended machine opera- tion, including, but not limited to, ...

  • Shindaiwa DH254 - page 9

    9 Examples of 50:1 mixing quantities IMPORT ANT! Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. Use of unmixed, improp- erly mixed, or stale fuel, may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow in ...

  • Shindaiwa DH254 - page 10

    10 Star ting Procedur e IMPORT ANT! Engine ignition is controlled by a two-position on-off switch mounted on the throttle body . This switch is typically labeled “I” for ON and “O” for OFF . NOTE: The blade cover is used for transpor tation and storage. Remove blade cover before using the unit. WARNING! Never start the engine from the opera ...

  • Shindaiwa DH254 - page 11

    11 When the motor starts... Open the choke by moving the choke lever backward (towar d the fuel tank). 1. If the engine does not continue to r un, repeat the appropriate cranking proce- 2. dures for a cold or war m engine.When the engine star ts, clear excess fuel from the combustion chamber by accelerating the engine several times with the throttl ...

  • Shindaiwa DH254 - page 12

    12 Clean around spark plug Lubricate cutters Check cutters and guide bar for damage and that bolts are tight Inspect/clean air lter element Inspect front and rear handles for damaged or loose attachments Inspect cooling ns, and clean as required Clean de- bris from tank and mufer Daily Maintenance/Inspection Figure 12 Maintenance and Adjus ...

  • Shindaiwa DH254 - page 13

    13 10-Hour Maintenance (more fr equently in dusty conditions) Figure 16 B Filter Element Air Cleaner Cover Pre- Filter Remove the air cleaner cover by loosening the two thumbscrews. See Figure 16A 1. . Remove and inspect the pre-filter . If the pre-filter is tor n or other wise damaged, 2. replace it with a new one. See Figure 16B. Clean the pre- ...

  • Shindaiwa DH254 - page 14

    14 Every 10 to 15 hours of operation: Rem ove a nd cl ean t he sp ark p lug . ■ Ad jus t the s par k plu g ele ct rod e gap t o 0.6 mm (0.024 in). If the spark plug must be replaced, use only an NGK CMR5H or equivalent resistor type spark plug of the correct heat range. See Figure 17. CA UTION! Before rem oving the s park pl ug, clean t he area a ...

  • Shindaiwa DH254 - page 15

    15 HT2510_20 Gearcase Lubrication VIEWED FROM THE BOTTOM Gearcase Grease Fitting CA UTION! Over-lubricating may cause the ■ gearcase to run slower than normal, and may also cause leakage from excess grease. Every 20 Hours Figure 21 VIEWED FROM THE BOTTOM Gearcase Cover Figure 20 Top of f gear case grease level by using a lever-type grease gun to ...

  • Shindaiwa DH254 - page 16

    16 Valve Adjustment Remove cylinder cover , r ocker ar m cover , and set piston at TDC-compression. 1. Loosen adjuster locknut so that the 2. 2.5 mm Allen socket head adjustment screw can tur n freely . Inser t feeler gauge .004 (0.10 mm) for both intake and exhaust; between valve 3. stem tip and rocker ar m. T ur n adjustment scr ew (clockwise = t ...

  • Shindaiwa DH254 - page 17

    17 Spar k Ar r ester Screen Maintenance If the engine becomes sluggish and low on power , check and clean the spark ar- rester screen. WARNING! Never operate the uni t with a damage d or mis sing muf  er or spark ar rester! Op erating wi th a missi ng or dam aged sp ark arrester is a re ha zard an d coul d also d am - age your hearin g. W ith ...

  • Shindaiwa DH254 - page 18

    18 The engine must retur n to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to per mit the engine clutch to disengage the cutters. WARNING! The cutters must NEVER engage at engine idle speeds! If the idle speed can- not be adjusted by the above procedure, return the trimmer to your Shindaiw ...

  • Shindaiwa DH254 - page 19

    19 T r oubleshooting Guide V aporlock. V alve adjustment. Engine hot/heat soaked. Low fuel quality . V alve clearance too tight. V alve clearance too loose. Let cool completely and restar t. Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO ...

  • Shindaiwa DH254 - page 20

    20 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose terminal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch is ...

  • Shindaiwa DH254 - page 21

    21 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose terminal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch is ...

  • Shindaiwa DH254 - page 22

    22 SHINDAIW A LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC'S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited W arranty , provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purc ...

  • Shindaiwa DH254 - page 23

    23 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. T o help ensure the performance of the unit, it is required to use engine oil which meets ...

  • Shindaiwa DH254 - page 24

    24 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equi ...

  • Shindaiwa DH254 - page 25

    25 NO TES: ...

  • Shindaiwa DH254 - page 26

    26 NO TES: ...

  • Shindaiwa DH254 - page 27

    27 NO TES: ...

  • Shindaiwa DH254 - page 28

    ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-8760, Japan Phone: 81-428-32-61 18 Fax: 81-428-32-6145 Ser vicing Infor ma tion Par ts/Serial Number Genuine Shindaiwa Parts and Assemblies for your S ...

メーカー Shindaiwa カテゴリー Trimmer

Shindaiwa DH254のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DH254の取扱説明書
- Shindaiwaの製品カード
- パンフレット
- またはShindaiwa DH254の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Shindaiwa DH254の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Shindaiwa DH254の取り付け説明書、サービスマニュアル、簡易説明書、またはShindaiwa DH254のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Shindaiwa DH254の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Shindaiwa DH254デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがShindaiwa DH254を使用するのを助ける技術的文書のことです。説明書は通常、全てのShindaiwa DH254ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Shindaiwaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Shindaiwa DH254の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははShindaiwa DH254の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Shindaiwa DH254に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Shindaiwa DH254デバイスの基本機能を使うにあたってのヒント。 Shindaiwa DH254のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Shindaiwa DH254に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるShindaiwa DH254のメーカー/サービスへの連絡先に関する情報。

Shindaiwa DH254についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもShindaiwa DH254の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがShindaiwa DH254で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)