Viking 855の取扱説明書

16ページ 0.99 mb
ダウンロード

ページに移動 of 16

Summary
  • Viking 855 - page 1

    TECHNICAL SER VICE MANUAL VIKING PUMP , INC. • A Unit of IDEX Corporation • Cedar Falls, IA 50613 USA SECTION TSM P AGE ISSUE Introduction ................................................................... 1 Special Information ....................................................... 3 Maintenance ............................................... ...

  • Viking 855 - page 2

    SECTION TSM 685.2 ISSUE C P AGE 2 OF 16 BEFORE opening any liquid chamber (pumping chamber , reservoir, relief valve adjusting cap fitting, etc.) be sure that : ● Any pressure in the chamber has been completely vented through the suction or discharge lines or other appropriate openings or connections. ● The pump drive system means (motor ...

  • Viking 855 - page 3

    SECTION TSM 685.2 ISSUE C P AGE 3 OF 16 FIGURE 3 RELIEF V AL VE POSITION SPECIAL INFORMA TION ROT A TION : Viking Mag Drive® pumps are designed to run in either direction. See PUMP ROT A TION, page 1 1. PRESSURE RELIEF V AL VES: 1. V ikin g pum ps are pos iti ve displ ace ment pump s and must be pro vid ed wit h some sort of pre ssu re pro tect io ...

  • Viking 855 - page 4

    GAUGE PORT BOSS STORAGE: If the pump and coupling are to be stored, drain the pump and pour non-detergent SAE 30-weight oil into the pump port. Apply grease to the pump or the coupling shaft extension, if present or accessible. Viking suggests rotating the pump shaft every 30 days to circulate the oil in the pump. The coupling should be stored in a ...

  • Viking 855 - page 5

    SECTION TSM 685.2 ISSUE C P AGE 5 OF 16 EXPLODED VIEW – SIZES AS, AK, AL, KE & KKE MAG-DRIVE PUMPS FIGURE 6 ITEM NAME OF P ART ITEM NAME OF P ART ITEM NAME OF P ART 1 Locknut 37 Idler 53 Locating Pin 21 Set Collar 38 Idler Bushing 60 Thrust W asher - 2 Req’d 25 Casing Bushing 39 Idler Pin 61 Machine Screws (metric) - 2 Req’d 30 Pipe Plug ...

  • Viking 855 - page 6

    SECTION TSM 685.2 ISSUE C P AGE 6 OF 16 MAGNETIC COUPLING OPTIONS Pump Size Magnetic Coupling Sizes AS B, C AK B, C AL B, C KE C KKE C COUPLING TORQUE AND SIZE OPTIONS T ABLE 3 TORQUE RA TINGS AND DRIVER CONNECTION OPTIONS Magnetic Coupling Sizes T orque Ratings (Ft-Lbs) Close-Coupled Long-Coupled IEC B-5 Flange Motor Mounts NEMA Motor Mounts Beari ...

  • Viking 855 - page 7

    SECTION TSM 685.2 ISSUE C P AGE 7 OF 16 6. Remove the idler and bushing assembly . If the idler bushing needs to be replaced, see “ INST ALLA TION OF BUSHINGS” on page 10. If further disassembly is required, the pump must be separated from coupling. Refer to “ DISASSEMBL Y OF COUPLING” on page 8 before proceeding with Step 7. 7. With the in ...

  • Viking 855 - page 8

    SECTION TSM 685.2 ISSUE C P AGE 8 OF 16 Buttonhead Screws Locknut Inner Magnet Set Collar Canister Bushing Canister O-ring Button Head Screws Canister and Casing Drain Holes DISASSEMBL Y OF COUPLING FIGURE 9 PUMP , INNER MAGNET AND CANISTER ASSEMBL Y Series MD2-B and MD2-C, All Sizes 1. Remove the piping to the ports and remove the capscrews securi ...

  • Viking 855 - page 9

    SECTION TSM 685.2 ISSUE C P AGE 9 OF 16 DISASSEMBL Y / ASSEMBL Y OF BEARING CARRIER DISASSEMBL Y The bearing carrier for an MD2 B coupling features two sealed ball bearings along with the outer magnet assembly . If further disassembly of this unit is required, reference Figure 7 on page 6 and Figure 13 then proceed as follows: 1. Remove the interna ...

  • Viking 855 - page 10

    SECTION TSM 685.2 ISSUE C P AGE 10 OF 16 INST ALLA TION OF BUSHINGS CARBON GRAPHITE The canister bushing (see Figure 9 on page 8) requires a special fixture for proper assembly so the bushing is only sold as part of the canister assembly . If attempting to install the carbon graphite idler or casing bushing, extreme care must be taken to prevent br ...

  • Viking 855 - page 11

    SECTION TSM 685.2 ISSUE C P AGE 11 OF 16 Do not attempt to reuse a PTFE (derivative) encapsulated O-ring if it has been removed. Immerse a new O-ring in boiling water for a few minutes. Remove it from the water and stretch out the O-ring so it will fit onto the casing hub without forcing it over a sharp edge. Run hot water* over the O-ring until it ...

  • Viking 855 - page 12

    SECTION TSM 685.2 ISSUE C P AGE 12 OF 16 Series MD2-B and MD2-C, All Sizes DANGER ! Follow these directions exactly to avoid injury to self or damage to the pumping unit. Be care- ful to keep the inner and outer magnets at least (1) foot apart until step 4. Do not engage the magnets in any other fashion. 1. Inspect the magnets for any steel objects ...

  • Viking 855 - page 13

    SECTION TSM 685.2 ISSUE C P AGE 13 OF 16 ADJUSTING END CLEARANCE T able 7-A provides standard operating end clearance for this pump. Use either of the following procedures to properly adjust the end clearance when replacing shims or reassembling the pump. FIGURE 21 PRESSURE RELIEF V AL VE INSTRUCTIONS Before opening any Viking pump liquid cham- ber ...

  • Viking 855 - page 14

    SECTION TSM 685.2 ISSUE C P AGE 14 OF 16 FIGURE 22 V AL VE – AS, AK, AL, KE AND KKE SIZES V AL VE - LIST OF P ARTS 1. V alve Cap 6. V alve Body 2. Adjusting Screw 7. V alve Spring 3. Lock Nut 8. Poppet 4. Spring Guide 9. Cap Gasket 5. Bonnet DISASSEMBL Y – RELIEF V AL VE Mark the valve and head before disassembly to insure proper reassembly . 1 ...

  • Viking 855 - page 15

    SECTION TSM 685.2 ISSUE C P AGE 15 OF 16 TROUBLESHOOTING Some of the following may help pinpoint the problem: Pump does not pump: • Pump has lost its prime from air leak or low level in tank. • Suction lift is too high. • Pump is rotating in the wrong direction. • The strainer may be clogged. • The bypass valve is open, the pressure relie ...

  • Viking 855 - page 16

    TECHNICAL SER VICE MANUAL VIKING PUMP , INC. • A Unit of IDEX Corporation • Cedar Falls, IA 50613 USA © 5/2007 Viking Pump Inc. All rights reserved SECTION TSM P AGE ISSUE W ARRANTY Viking warrants all products manufactured by it to be free from defects in workmanship or material for a period of one (1) year from date of startup, provided that ...

メーカー Viking カテゴリー Water Pump

Viking 855のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 855の取扱説明書
- Vikingの製品カード
- パンフレット
- またはViking 855の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Viking 855の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Viking 855の取り付け説明書、サービスマニュアル、簡易説明書、またはViking 855のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Viking 855の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Viking 855デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがViking 855を使用するのを助ける技術的文書のことです。説明書は通常、全てのViking 855ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vikingの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Viking 855の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははViking 855の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Viking 855に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Viking 855デバイスの基本機能を使うにあたってのヒント。 Viking 855のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Viking 855に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるViking 855のメーカー/サービスへの連絡先に関する情報。

Viking 855についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもViking 855の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがViking 855で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)