Windsor SGJ32の取扱説明書

42ページ 2.32 mb
ダウンロード

ページに移動 of 42

Summary
  • Windsor SGJ32 - page 1

    PRV MODELS: SGJ32 10052530 A FTER SN: 100013640 4 86037680 11/05/08 PRV NO. 980230 N SCRUBBER Operating Instructions Read these instructions before using the machine ...

  • Windsor SGJ32 - page 2

    MACHINE DATA LOG/OVERVIEW SGJ32 86037680 01/03/07 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ___________________________________ ______________________________ _____________ Address: __________________ ___________________________________ ______________________________ ____________ Ph ...

  • Windsor SGJ32 - page 3

    TABLE OF CONTENTS SGJ32 86037680 11/05/08 3 Machine Data Log/ Overview . ............................... 2 Table of Co ntents ................................................. 3 HOW TO USE THIS MANUAL How to use this Manual. ....................................... 1-1 SAFETY Important Safety Instructions ............................... 2-1 Hazard I ...

  • Windsor SGJ32 - page 4

    HOW TO USE THIS MANUAL SGJ32 86037680 11/05/08 1-1 This manual contains the f ollowing sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authori zed Windsor dealers. When p ...

  • Windsor SGJ32 - page 5

    SGJ32 86037680 01/03/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described i ...

  • Windsor SGJ32 - page 6

    HAZARD INTENSITY LEVEL SGJ32 86037680 01/03/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WAR ...

  • Windsor SGJ32 - page 7

    SAFETY LABEL LOCATION SGJ32 86037680 01/03/07 2-3 PINCH POINT WARNING 86243830 PRV NO. 500663 (2) NOTE: These drawings indicate the location of safet y labels on the machine. If at any time the labels be come illegible, promptly replace them. SAFETY DECAL 86242480 PRV NO. 500111 BATTERY C AUTION 86248210 PRV NO. 500109 HORN DECAL 86248210 PRV NO. 8 ...

  • Windsor SGJ32 - page 8

    TECHNICAL SPECIFICATIONS SGJ32 86037680 01/03/07 3-1 ITEM DIMENSION/CAPACIT Y Nominal power 2.9 kW Rated Voltage 36 Volts DC Rated Amperage 80 amps Batteries 6 x 6 Volt 250-335 AH @20 hr. rate Scrub Brush Motors 2 x 1.0 HP (746 W) Vacuum Motor(s) 1 x .75 HP (560 W) Standard, second motor optional Propelling Motor 1.3 HP (932 W) Mass (GVW) 1810 lbs ...

  • Windsor SGJ32 - page 9

    TECHNICAL SPECIFICATIONS SGJ32 86037680 01/03/07 3-2 ITEM MEASURE Height 1 51 inches (130 cm) Height 2 56.6 inches (144 cm) Length 63.5 inches (161 cm) Width without squeege e an d scrub head 31 inches (79 cm) Width of squeegee 33 inches (84 cm) Width of scrub path for 32 in. (81 cm) 32 inches (81 cm) The weighted root mean square a cceleration at ...

  • Windsor SGJ32 - page 10

    HOW THE MACHINE WORKS SGJ32 86037680 01/03/07 3-3 The Saber Glide is a battery powered, self- propelled, hard floor scrubber intended fo r commercial use. The appliance applies a clea ning solution onto a hard floor, scrubs the floo r with brushes, and then vacuum s the soiled water back into the recovery tank. The machine's primary sy stems a ...

  • Windsor SGJ32 - page 11

    COMPONENTS SGJ32 86037680 01/03/07 3-4 1. Control panel 2. Front cover 3. Side cover 4. Tank 5. Recovery tank cover 6. Recovery tank dome 7. Recovery tank drain hose 1 2 4 3 11 5 6 8 9 10 12 13 7 8. Scrub head 9. Scrub head side squeegee 10. Solution tank drain hose 11. Solution tank cover 12. Squeegee 13. Vacuum motor ...

  • Windsor SGJ32 - page 12

    CONTROLS SGJ32 86037680 01/03/07 3-5 1 2 3 4 5 6 7 10 8 13 20 14 11 20 16 12 19 17 18 15 9 ...

  • Windsor SGJ32 - page 13

    CONTROLS SGJ32 86037680 01/03/07 3-6 1. Key switch 2. Emergency stop button 3. One touch switch 4. Brush pressure switch 5. Solution control switch 6. Vacuum/squeegee switch 7. Display toggle switch • Information Screen 1 • Information Screen 2 • Hour meter • Fault codes and special icons • Battery meter 8. Recycle switch (optional) 9. Re ...

  • Windsor SGJ32 - page 14

    CONTROLS SGJ32 86037680 01/03/07 3-7 3. ONE TOUCH SWITCH This switch controls the scrub bru shes and vacuum all in one touch . To start scrubbing, press the one touch switch. The brush drive mot ors will turn on, the scrub deck will lower to the "light scrub" position, the solution will flow at “two bars” rate, the squeege e will lowe ...

  • Windsor SGJ32 - page 15

    CONTROLS SGJ32 86037680 01/03/07 3-8 Indicates vac motor is runni ng 5. SOLUTION CONTROL SWITCH This switch controls the amount of solu tion flow to t he scrub deck. There are 7 different flow settings. To increase the solution flow, press the solution control sw itch (+). To decrea se solution flow, press the top of the switch (-). If the brush mo ...

  • Windsor SGJ32 - page 16

    CONTROLS SGJ32 86037680 01/03/07 3-9 7. DISPLAY TOGGLE SWITCH The display toggle switch allows you to cha nge the in formation display screen. Two screens are available. • Fault codes/icon will appe ar on either display screen when the controller d etects a problem within the electrical system. The codes/icons a re used to assist u se rs a s well ...

  • Windsor SGJ32 - page 17

    CONTROLS SGJ32 86037680 01/03/07 3-10 • The float switch is located inside the re covery tank. The purpose of the float switch is to notify the user that the recovery tank is full. When the float switch is activa ted, the scrub brush motors and solution flow will sto p, the scrub deck will raise, the squeegee will rise after 60 seconds, and the v ...

  • Windsor SGJ32 - page 18

    CONTROLS SGJ32 86037680 01/03/07 3-11 8. RECYCLE SWITCH (OPTIONAL) This switch controls the solution re cycle pump. To start recycle pump, press the switch. A green light above the circuit breakers will indicate that pump is on. The solution co ntrol switch will control the speed of the pump and therefore the amount of soluti on flow to the scrub d ...

  • Windsor SGJ32 - page 19

    CONTROLS SGJ32 86037680 01/03/07 3-12 11. BRAKE PEDAL The brake pedal is located on the floor to the right side of the steering colum n pedestal. The pedal operates the disc brake on the drive wheel. To slow or st op the vehicle, apply pressure to the brake pedal. 12. PARKING BRAKE LEVER The black knob located on the right side of the steerin g col ...

  • Windsor SGJ32 - page 20

    CONTROLS SGJ32 86037680 01/03/07 3-13 14. STEERING WHEEL The steering wheel turns the front wh eel causing the machine to change dire ction. 15. STEERING TILT LEVER The steering tilt lever is located on the right side of the steering wh eel. To enga ge the tilt adjustment, pull on the lever and adjust the steering colum n to de sired position. Rele ...

  • Windsor SGJ32 - page 21

    MACHINE OPERATION SGJ32 86037680 01/03/07 3-14 ! WA RNI NG PRE-RUN MACHINE INSPECTION 1. Do a pre-run inspection to find possi ble problems that could cau se poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. Visually check for exterior damage, leaks, damaged or worn tires. 2. Check brushes or ...

  • Windsor SGJ32 - page 22

    MACHINE OPERATION SGJ32 86037680 01/03/07 3-15 ! CA UTI ON ! WA RNI NG TO BEGIN SCRUBBING When operating the machine around people, pay close attention for unexpec ted movement. Use extra caution around children. 1. Place right foot on brake pedal or che ck to make sure parking bra ke ha s be en set. 2. With directional pedal in neutral turn key sw ...

  • Windsor SGJ32 - page 23

    MACHINE OPERATION SGJ32 86037680 01/03/07 3-16 EMPTYING AND CLEANING TANKS RECOVERY TANK 1. Touch the one-touch switch (#1) on the control panel to raise the scrub deck, stop the motors, and solution flow, raise the sque ege e and turn off vacuum motors. 2. Park the machine next to a floor drain. Drain hose is on left rear corner of machine. 3. Tur ...

  • Windsor SGJ32 - page 24

    MAINTENANCE SGJ32 86037680 01/03/07 4-1 1. Batteries 2. Squeegee Adjustment 3. Side Squeegee Adjustment 4. Scrub Brushes 5. Vacuum Filter 6. Float Switch 7. Solution Strainer 8. Brake 9. Steering Chain Tensioner 10. Vacuum Motor 11. Brush Motor 12. Traction Motor 13. Fuse 14. Circuit Breaker 15. Squeegee Lift Actuator 16. Scrub Lift Actuator 1 2 3 ...

  • Windsor SGJ32 - page 25

    MAINTENANCE SGJ32 86037680 01/03/07 4- 2 ! WA RNI NG ! WA RNI NG ! WA RNI NG SPECIFIC GRAVITY BATTERY CONDITION 1.265 100% CHARGED 1.225 75% CHARGED 1.190 50% CHARGED 1.155 25% CHARGED 1.120 DISCHARGED ! WA RNI NG 1. BATTERIES The batteries provide the power to ope rate the machine. The batteries require regul ar maintenance to keep them operating ...

  • Windsor SGJ32 - page 26

    MAINTENANCE SGJ32 86037680 01/03/07 4-3 ! WA RNI NG ! WA RNI NG ! WA RNI NG ! WA RNI NG ! WA RNI NG TO CHARGE BATTERIES When servicing machine, avoid contact with acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame a way. Keep covers open when charging. Wear eye protection and protec tive clothing wh e n wo r ...

  • Windsor SGJ32 - page 27

    MAINTENANCE SGJ32 86037680 01/03/07 4-4 ! CA UTION TO REMOVE BATTERIES 1. Stop the machine in a clean area next to the charger. 2. Turn off machine and set parking bra ke . FOR SAFETY: Before leaving or servicing machine, stop on level surface, apply parking brake, turn off machine and remov e k ey. 3. Raise the seat plate. 4. Remove side cover. 5. ...

  • Windsor SGJ32 - page 28

    MAINTENANCE 4-5 SGJ32 86037680 01/03/07 2. SQUEEGEE ADJUSTMENT Adjusting the squeegee is a two-p art process. First, the squeegee tool must have corre ct pitch in orde r for the squeegee blade to have the same deflectio n at each tip as well as the center. The pitch adjustment is facilitated by the use of a spirit level mounted on the squeegee tool ...

  • Windsor SGJ32 - page 29

    MAINTENANCE SGJ32 86037680 01/03/07 4- 6 TO REPLACE OR ROTATE REAR SQUEEGEE BLADES 1. With the squeegee in the up position, turn off the key switch and set the parking brake. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off mac hine and remove key. 2. Unlock and pull open latch on rea r of squeegee tool. 3. Remove bl ...

  • Windsor SGJ32 - page 30

    MAINTENANCE SGJ32 86037680 01/03/07 4-7 3. SIDE SQUEEGEE ADJUSTMENT TO REPLACE OR ROTATE SIDE SQUEEGEE BLADES 1. Loosen the locking knob and pivot the side squeegee out as if to expose the brush. 2. Loosen and remove the three nuts and bolts securing squeegee blade s. 3. Remove the retaining strap and squee gee blade and rotate or replace sque egee ...

  • Windsor SGJ32 - page 31

    MAINTENANCE SGJ32 86037680 01/03/07 4-8 4. SCRUB BRUSHES There are five different types of brushes available to cover applications from cle aning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market and further add to the flexibility of the machine. Please refer to the followin ...

  • Windsor SGJ32 - page 32

    MAINTENANCE SGJ32 86037680 01/03/07 4-9 5. VACUUM FILTER The vacuum filter is located inside the recovery tank. The vacuum filter prevents debris from entering the vacuum motor. Daily remove and clean filter of any debris for maximum airflow. 6. FLOAT SWITCH The float switch is located inside the recovery tank. The purpose of the float switch is to ...

  • Windsor SGJ32 - page 33

    MAINTENANCE SGJ32 86037680 01/03/07 4-1 0 10. VA CUUM MOTOR (Refer to the Vacuum Group in the parts se ction of manual) Do not use a pressure w asher to clean around the vacuum motors. Use tap pressur e only. Care must be taken so that water is not directed into vacuum motor air intakes. CHANGING VACUUM MOTOR 1. Remove side cover. 2. Disconnect ele ...

  • Windsor SGJ32 - page 34

    MAINTENANCE 4-11 SGJ32 86037680 01/03/0 7 ! WA RNING 11. BRUSH MOTOR (Refer to Brush Motor Group in part s se ction of manual). Do not use a pressure washer to clean a roun d the brush motors. Use tap pressure only. CHANGING BRUSH MOTORS 1. With the scrub deck in the stored positio n, disconnect brush motor wiring co nnector from harness. 2. Loosen ...

  • Windsor SGJ32 - page 35

    MAINTENANCE SGJ32 86037680 01/03/07 4-12 ! WA RNING 12. TRACTION MOTOR Do not use a pressure washer to clean around the brush motors. Use tap pressur e only . TRACTION MOTO R CARBON BRUSH REPLACMENT FOR SAFETY: Before leaving or servicing m achine, stop on a level surface, turn off machine and remove key. 1. Disconnect batteries from machi ne. 2. T ...

  • Windsor SGJ32 - page 36

    MAINTENANCE SGJ32 86037680 01/03/07 4-13 15. SQUEEGEE ACTUATOR REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake. 1. Remove squeegee to gain access to lift system. 2. Lower squeegee lift linkage, if possible, by pressing bottom of vacuu m/squeegee switch and turn key ...

  • Windsor SGJ32 - page 37

    MAINTENANCE SGJ32 86037680 01/03/07 4-14 16. SCRUB DECK ACTUATOR REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake. 1. Lower scrub deck, if pos sible, by pressing one- touch switch and turn key to off position. 2. Remove lower clevis pin by removing rue ring from cle ...

  • Windsor SGJ32 - page 38

    TRANSPORTING MACHINE SGJ32 86037680 01/03/07 4-15 TOWING OR PUSHING MACHINE The machine may be towed for short distance s at speeds not to exceed 5 mph. Be careful to avoid damaging machine. Attach towing devic e at tie down point. The machine may be pushed by hand from the rear. NOTE: To avoid damage caused by regenerative voltage, disconnect trac ...

  • Windsor SGJ32 - page 39

    JACKING MACHINE SGJ32 86037680 01/03/07 4-16 MACHINE JACKING The machine may be jacked up for service or inspection by using the spe cified ja ck lo cations. Always block the tires when jacking up the machine. FOR SAFETY: Before leaving or servicing machine; Stop on level surface, set parking brake, turn off machine and remove k ey. The rear jack p ...

  • Windsor SGJ32 - page 40

    MAINTENANCE SGJ32 86037680 01/03/07 4-17 SERVICE SCHEDULE MAINTENANCE BEFORE EACH WORK PERIOD AFTER EACH WORK PERIOD 50 HRS 100 HRS 200 HRS Check water level of batteries after charging; add distilled water if necessary * Check that recovery tank cover seals tightly * Visually check for damaged or wo rn tire s * Check brushes or pad s for proper in ...

  • Windsor SGJ32 - page 41

    MACHINE TROUBLESHOOTING SGJ32 86037680 01/03/07 4-1 8 PROBLEM CAUSE ERROR CODE SOLUTION Battery disconnected Check co nnections of all battery cable connections Emergency shut-off activated Reset Battery cables corroded Clean connections Main fuse blown Replace fuse No power to machine Faulty key switch Replace switch Low battery charge Charge batt ...

  • Windsor SGJ32 - page 42

    MACHINE TROUBLESHOOTING SGJ32 86037680 01/03/07 4-19 PROBLEM CAUSE ERROR CODE SOLUTION Vacuum motor does not run, or runs slowly Recovery tank full Drain recovery tank Recovery tank float switch dirty Clean float switch Loose motor connection 7700 Check motor wires an d connectio ns Worn vacuum motor brushes Replace brushes, check commutator Poor s ...

メーカー Windsor カテゴリー Vacuum Cleaner

Windsor SGJ32のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SGJ32の取扱説明書
- Windsorの製品カード
- パンフレット
- またはWindsor SGJ32の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Windsor SGJ32の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Windsor SGJ32の取り付け説明書、サービスマニュアル、簡易説明書、またはWindsor SGJ32のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Windsor SGJ32の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Windsor SGJ32デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWindsor SGJ32を使用するのを助ける技術的文書のことです。説明書は通常、全てのWindsor SGJ32ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Windsorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Windsor SGJ32の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWindsor SGJ32の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Windsor SGJ32に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Windsor SGJ32デバイスの基本機能を使うにあたってのヒント。 Windsor SGJ32のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Windsor SGJ32に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWindsor SGJ32のメーカー/サービスへの連絡先に関する情報。

Windsor SGJ32についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWindsor SGJ32の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWindsor SGJ32で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)