日本語 dropdown-ico

Geovision GV-RK1352の取扱説明書

21ページ 関係なし
ダウンロード

ページに移動 of 21

Summary
  • Geovision GV-RK1352 - page 1

    GV-RK1352 and GV-R13 52 Card Reader The GV-RK1352 and GV-R1352 are card r eaders designed to recognize ident ifications cards. GV-RK1352 comes with keypad, allowing it to also recognize PIN codes. Featured w ith the W ie gand and RS-485 outputs, the readers can be connected to any standard access con trol panel. The readers are protected by a weath ...

  • Geovision GV-RK1352 - page 2

    1. Physical Descriptions 1.1 E lectric Wire GV-RK1352 Wire C olor Function Red DC 7.5 ~ 12 V Black GND Yellow Beeper Orange G reen LED Light Red Red LED Green W ie gand Data 0 W hi te W ie gand Data 1 Blue RS-485 + Light Blue RS-485 - Rear Vie w GV-R1352 Wire Color Function Red DC 7.5 ~ 12V Black GND Yellow Beeper Orange G reen LED Light Red Red LE ...

  • Geovision GV-RK1352 - page 3

    1.2 Key pad (GV-RK1352 Only ) W he n accessing an entry using GV-RK1352, you can enter the door’s PIN code on the keypad or present the card and then enter the card’s PIN code on the keypad to be granted access. The access mod e is defined on GV-ASManager. 1. 0~9 Number Key s: Press the number keys to enter the PI N code . 2. # Key: Press the # ...

  • Geovision GV-RK1352 - page 4

    2. Connecting th e Reader to GV-AS Controller You can connect the readers to GV-AS Controllers through Wiegand or RS-485 inter f ace. Note that the connection between the reader and GV-AS Controller varies with diff erent controller models. To see how many readers can be connected to a GV-AS Controller, refer to The Number o f Readers Supported by ...

  • Geovision GV-RK1352 - page 5

    2.2 Connecting through RS-485 Interface The following diagrams use GV-RK1352 and GV-A S810 Controll er as an example. Up to eight readers can be connected together to the RS-485 interface on GV-AS810 Contro ller. z Connecting four or less readers to GV-AS810 Controller : Wire C olor Function Black GND Light Blue RS-485 - Blue RS-485 + Red DC 7.5 ~ ...

  • Geovision GV-RK1352 - page 6

    2.2.1 Defining Reade rs on GV-AS Controller Web Interface Since multiple r eaders c an connect to GV-AS Controller using one RS-485 interface, you need to specify w hich door each reader controls. This section explains how to define readers on the W eb interface of GV-AS Controller. On the W eb interface, you can also set the reader to read the GID ...

  • Geovision GV-RK1352 - page 7

    4. N ext to Read Mode , select Read UID or Read GID to set the conne cted readers to read UID (unique identifier) or GID (G eoVision ID) on GV- AS ID Cards / Key Fobs. If you select Read GID , make sure there are two numbers on your GV-AS ID Cards / Key Fobs as show n below. If ther e is only one number on your GV-AS ID Cards / Key Fobs, GID is not ...

  • Geovision GV-RK1352 - page 8

    3. Installing the GV-R/RK/DFR Config A P Th master / slave status, and whether it reads UID or GID. W hen using the Con f ig AP, the reader needs to be connected to a PC through GV-COM, GV-Hub or GV-NET/IO Car d V3.1. e GV-R/RK/DFR Config AP allows you to set the reader’s beeper / LED, ID number, You can inst fig AP from the Software DVD or GeoVi ...

  • Geovision GV-RK1352 - page 9

    4. Overlaying Card Numb ers on GV-System Li v e Vie w You can overlay card numbers recogniz ed at the reader onto a camera ch annel on GV- System. To overlay card numbers on GV-System channel, the reader needs to be c onnected to a GV-Sy stem th rou gh GV-C OM , GV-Hub or G V-NET /IO Ca rd V3. 1. RS-4 85 GV-HUB / GV-COM / GV-NET/IO Card RS-2 32 GV- ...

  • Geovision GV-RK1352 - page 10

    2. Select the COM port that is connected to the reader and click Op en C OM . The seria number and firmware version of the reader will be automatically detected. The red s next to 3. Under l quare the COM port box should change to blue to indicate the COM port is correct. M aster / Slave , set the reader to Slave . If you want to connect multiple r ...

  • Geovision GV-RK1352 - page 11

    4.2 A dding the Reader to GV-Sy stem 1. In GV -System , cli ck the Configure button, select A ccessories , and select GV Wiegand Capture Device Setting . This dialog box appears. 2. Click the New butt on. This dialog box appear s.  Type: Select GV-W ie gand Capture. February 6, 2015 11  Device: Type a number and name to help y ou identify the ...

  • Geovision GV-RK1352 - page 12

    5. Changing t he Default Se ttings of Bee per and LED You can change the defa ult sett ings of the LED and the beeper by enabling a GV-AS210 / d LED, green LED or beeper when the specified alarm events occur. For GV -AS400, built-in LED and beeper settings are available on the W eb interface for outputs 9 ~ 16. The GV-AS Controller and the reader n ...

  • Geovision GV-RK1352 - page 13

    2. Click Open COM . The serial number and the firmware version of the reader will be automatically detected. 3. T o enable external control o f Beeper or LED, sel ect Beeper , Green LED or Red LED . 4. Select Master from the M aster / Slave drop-down list. ID number set on the Extended Reader page of the GV-AS Controller Web interface. 6. Click Set ...

  • Geovision GV-RK1352 - page 14

    5.2 Wiring the Beeper and LED to the GV-A S Controller To wire the beeper and L ED to GV-AS210 / 2110 / 400 / 410 / 4110 / 810 / 8110, connect the control wires of the reader’s Beeper, Red LED or Green LED to any of the outputs on GV-AS Controller. Not e that outputs 9 ~ 16 on GV-AS400 are used for the built-in LED and beeper settin gs. Wiring LE ...

  • Geovision GV-RK1352 - page 15

    After wiring, you also need to go to GV-ASManager to select the alarm conditions that will set the device list, off the reader’s beeper. In GV-ASManager, right-click the GV-AS Controller in click Settings , and click the Door / Gate tab to select the alarm condi tions. February 6, 2015 15 ...

  • Geovision GV-RK1352 - page 16

    5.3 Configuring the Beeper and LED Settings for Eac h Door/Gate After connecting the wires for beeper o r LED, specify the conditions to trigger the beeper and LED on the GV-AS210 / 2110 / 400 / 410 / 4110 / 810 / 8110 Web interface. 1. O n the controller W eb interface, click Output Setting . The page below appears. 2. Find the output wired to the ...

  • Geovision GV-RK1352 - page 17

    6. Setting UID or GID on GV-R/RK/DFR Config A P By default, the readers read the UID (unique identi f ier) on ID cards or key fobs. Using GV- R/RK/DFR Config AP, you can set the GV-RK1352 / GV-R1352 to read GID (GeoVision ID) n GV-AS ID Cards / Key Fobs instead. o Note: 1. To see how to install the Config AP and how to identify the COM port of the ...

  • Geovision GV-RK1352 - page 18

    To use GID, make sure there a re two numbers on your GV-AS ID Cards / Key Fobs as shown below. If there is only one number on your GV-AS ID Cards / Key Fobs, GID is no t supported and you must select Unique Identification ( UID). February 6, 2015 18 ...

  • Geovision GV-RK1352 - page 19

    7. Firmw are Upgrade included in the Software CD. Important Note s before You Start Before you start updating the firmware, please read these important notes: 1. W hile the firmware is being updated, the power supply must not be interrupted. 2. Do not turn the power off within 10 minutes after the firmware is updated. GeoVision will periodically re ...

  • Geovision GV-RK1352 - page 20

    8. Specification s GV-RK1352 GV-R1352 CPU 8-bit microprocesso r Frequency 13.56 M Mifare C Hz for ISO14443A (Mifare DESFire, Mifare Plus and lass) Wiegand Interface W ie gand 26 / 34 bits, distance 30 m / 98.43 ft RS-485 9,600 bps, connect up to 8 GV-RK1352 / R1352 units Power DC 7.5 ~ 12V LED Red, Green and Blue LED Beeper Buzzer Reader Color Blac ...

  • Geovision GV-RK1352 - page 21

    February 6, 2015 21 RK1352 Onl y) O tional accessories can ex p bilities and versatilit V-RK1352 Card Reader. Consult your sales r information. 9. Accessor y (GV- p and the capa ies of your G epresentative for more GV -MountA 900 • Dim GV-Moun 2 to a US s er box. ens • Weight: tA900 is a mounting plate that allows you to attach GV-RK135 ingle g ...

メーカー Geovision カテゴリー Security access control system

Geovision GV-RK1352のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GV-RK1352の取扱説明書
- Geovisionの製品カード
- パンフレット
- またはGeovision GV-RK1352の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Geovision GV-RK1352の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Geovision GV-RK1352の取り付け説明書、サービスマニュアル、簡易説明書、またはGeovision GV-RK1352のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Geovision GV-RK1352の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Geovision GV-RK1352デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGeovision GV-RK1352を使用するのを助ける技術的文書のことです。説明書は通常、全てのGeovision GV-RK1352ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Geovisionの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Geovision GV-RK1352の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGeovision GV-RK1352の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Geovision GV-RK1352に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Geovision GV-RK1352デバイスの基本機能を使うにあたってのヒント。 Geovision GV-RK1352のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Geovision GV-RK1352に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGeovision GV-RK1352のメーカー/サービスへの連絡先に関する情報。

Geovision GV-RK1352についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもGeovision GV-RK1352の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGeovision GV-RK1352で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)