日本語 dropdown-ico

Epson M X - 8 5の取扱説明書

36ページ 0.53 mb
ダウンロード

ページに移動 of 36

Summary
  • Epson M X - 8 5 - page 1

    MX-8 5 DOT MATRIX PRINTER Operation Manual P8290062-1 ...

  • Epson M X - 8 5 - page 2

    Copyright © 1982 by EPSON Shinshu Seiki Co., Ltd. Nagano, Japan “All rights reserved” *The contents of this manual are subject to change without notice. ...

  • Epson M X - 8 5 - page 3

    TABLE OF CONTENTS INTRODUCTlON ........................................................................................................ 1 INSTALLATlON ........................................................................................................... 2 1. Unpacking & Set-up of MX-85 ...................................................... ...

  • Epson M X - 8 5 - page 4

    LIST OF FIGURES Fig. 1 MX-85 Dot Matrix Printer ........................................................................... 1 Fig. 2 Contents of Carton.. .................................................................................... 3 Fig. 3 Removal of Printer Cover ........................................................................... 4 ...

  • Epson M X - 8 5 - page 5

    LIST OF TABLES Table 1 Function and Conditions of DIP Switch B ............................................. 10 Table 2 Function and Conditions of DIP Switch A ............................................. 10 Table 3 Baud Rate Selection.. .............................................................................. 11 Table 4 ASCII Code Table Sele ...

  • Epson M X - 8 5 - page 6

    INTRODUCTION The MX-85 Dot Matrix Printer is a highly versatile communication grade terminal printer, with the following features: 1. Print Speed: 80 CPS 2. Microprocessor controlled, logic seeking, bidirectional printing 3. Interface: Serial - RS-232C and 20 to 80 mA Current Loop 4. Transmission Code: ASCII and Baudot - 45.5 to 9600 baud 5. Buffer ...

  • Epson M X - 8 5 - page 7

    INSTALLATION 1. Unpacking & Set-up of MX-85 Before removing the MX-85 from the carton, check the box for evidence of shipping damage. If such evidence is present, notify the carrier immediately. 1.1. Unpacking (1) Open carton. (2) Remove accessories; ribbon, manual, etc. (3) Grasp the MX-85 by, its underside and lift straight out with ‘packin ...

  • Epson M X - 8 5 - page 8

    1.3. Contents of carton The Carton should contain the following: 1. MX-85 Printer 2. Cartridge Ribbon 3. Operation Manual 4. Roll Paper Holder 5. AC Power Cord 6. Filter Circuit Board If there is any evidence of damage or missing items, contact the vendor from whom the printer was purchased to report the details. 6. Filter Circuit Board (Y4252O4000 ...

  • Epson M X - 8 5 - page 9

    1.4. Operation site 1. The MX-85 should be installed on a flat, firm surface with adequate room to the rear to accommodate the roll paper holder and paper rewind device if so equipped. 2. Care should be exercised in locating the MX-85 in areas where it will not be exposed to direct sunlight or where the environment contains grease or dust. 3. The M ...

  • Epson M X - 8 5 - page 10

    Lower Case Shipping Screws 1.7. Removal of shipping screws 1. Turn the MX-85 upside down, exercising care so the paper release lever is not bent. 2. Remove the two (2) shipping screws from the lower case. NOTE: These shipping screws should be retained for use during reshipment of the MX-85. They are necessary to prevent damage to the print mechanis ...

  • Epson M X - 8 5 - page 11

    Pull out Fig. 5 Removing Manual Paper Feed Knob 3. Turn the Printer upside down, observing caution with the paper roll release 4. Loosen the four (4) Phillips head screws located in the extreme corners of the bottom cover. NOTE: Placing tape over the holes will prevent accidental loss of the screws when the Printer is inverted. 5. Turn the Printer ...

  • Epson M X - 8 5 - page 12

    Upper Case Lead Wire Fig. 7 Removing Wires Connected to Control Panel 2. Construction and Location of the MX-85 Com- ponents At this time, the following main components of the MX-85 Printer and their respective locations can be observed: 1. Transformer & Filter Circuit Board 2. SMDP Board - Top 3. SMCT Board - Bottom 4. Printer Mechanism - M-33 ...

  • Epson M X - 8 5 - page 13

    Construction of the Printer Controller Printer Machanism Control Panel Transformer & Filter Circuit Board Transformer & Filter Circuit Board Controller Printer Mechanism MX-85 Dot Matrix Printer SMDP Board (Driver Circuit Board) Connector (male and female) SMCT Board (Control Circuit Board) Spacer Controller Fig. 8 Construction of the Print ...

  • Epson M X - 8 5 - page 14

    3. Setting of DIP Switches and Jumpers 3.1. Location of DIP switches and jumpers In order to suit each user’s specific requirements, there are two (2) DIP (Dual In-Line Pin) switches located on the SMDP Board and sixteen (16) jumpers located on the SMCT Board. 3.2. Setting DIP switches - SW-A and SW-B 1. With the top cover removed, observe the SM ...

  • Epson M X - 8 5 - page 15

    Fig. 10 Setting DIP Swtiches Table 1 Functions and Conditions of DIP Switch B Pin No. Function Off On Factory-set B1 O N B 2 See OFF B3 Baud Rate Table 3 O N B 4 OFF Table 2 Functions and Conditions of DIP Switch A Pin No. Functio n Off On Factory-set A 1 Transmission ASCII BAUDOT OFF Cod e A 2 In ASCII mod e See Table 4 ON A 3 sets Word Struc- ON ...

  • Epson M X - 8 5 - page 16

    4. Now using Table 2, select your transmission code: ASCII or Baudot. A. If ASCII is selected, refer to Table 4 for word length setting and parity control. B. If Baudot is selected, refer to Table 5 for selection of correct Baudot code. 5. Set Line Spacing to desired position. 6. Set Auto Feed if required. This is necessary if the host system does ...

  • Epson M X - 8 5 - page 17

    3.3. Setting of jumpers Your application may require the removal or installation of jumpers of the SMCT Board. Before continuing, consult Table 6 which outlines the function and factory-set condition of each jumper. In order to access the SMCT Board it is necessary to remove the SMDP Board. This is accomplished by: 1. Disconnecting the Mechanism Ca ...

  • Epson M X - 8 5 - page 18

    Jumper OFF Jumper ON Fig. 11 Jumpers on the SMCT Board -13- ...

  • Epson M X - 8 5 - page 19

    4. Power Supply Verify that the power supply is set correctly for your application. Check to see that the wire connected to the filter board is securely fastened to the correct voltage position. If it is necessary to change the voltage, use a flat blade screwdriver to loosen the existing connection and reconnect to the desired voltage. This change ...

  • Epson M X - 8 5 - page 20

    5. Cartridge Ribbon Installation 1. Position the Printer with the logo facing you. 2. Lift the Printer cover. 3. Be sure the print scale is pushed to the rear, against the platen. 4. Remove the ribbon from its box and turn the knob counterclockwise to remove any slack. 5. Guide the four (4) tabs on the cartridge into the mechanism side frames. 6. P ...

  • Epson M X - 8 5 - page 21

    Fig. 14 Cartridge Ribbon Setting -Ribbon Ribbon Mask Incorrect Incorrect Correct Fig. 15 Examples of Correct and Incorrect Ribbon Setting 6. Paper Holder Installation The following steps should be performed with the power off. 1. Set the paper holder behind the MX-85 and locate the rear rubber feet of the Printer in the forward holes of the paper h ...

  • Epson M X - 8 5 - page 22

    2. Plug jack type connector, which is connected to the “Low Paper” sensor, into the mating connector located alongside of the 25-pin EIA connector on the rear of the MX-85. 3. Lift the printer cover and slide the print head to approximately the center of the printer. 4. Pull the print scale forward and push the paper release to the rear. 5. Mou ...

  • Epson M X - 8 5 - page 23

    Roll Paper Fig. 17 Loading of Rool Paper (2) Manual Paper Feed Knob Fig. 18 Loading of Roll Paper (3) 7. Gap Adjustment It is possible to adjust the gap between the print head and platen to accommodate various thicknesses of form and print density. The head adjusting lever is located on the left side frame of the print mechanism. Move forward to wi ...

  • Epson M X - 8 5 - page 24

    Head Adjusting Lever (Side View) Paper Position of adjusting lever Single-leaf paper Multi-copy paper sheets Set the lever to the 4th step. Set the lever to the 7th step. Fig. 19 Gap Adjustment -19 - ...

  • Epson M X - 8 5 - page 25

    OPERATION Power On 1. Plug in AC power cord. 2. Turn on the Printer - switch located to the rear on the right side of the Printer. 1) Buzzer will sound. 2) Print head will return to the left side of the Printer. 3) The “Power”, “Ready” and “On-Line” indicators should be lit on the control panel. “Paper-Out” indicator will be off. 1. ...

  • Epson M X - 8 5 - page 26

    2. Self -Test The MX-85 has a self-test routine programmed into the Controller. It is useful to check the operation of the print head and the print mechanism (ribbon, motors, belt, etc.). The input connector is not checked with this test. 1. Be sure there is an adequate supply of paper in the Printer. The test requires about 22 inches. 2. Turn’of ...

  • Epson M X - 8 5 - page 27

    Table 7 25-pin EIA Connector I Pin No. Signal Name 1 Chassis Ground 2 TXD 3 RXD 4 RTS 5 CTS 7 Signal Ground 11 Reverse Channel (REV) 20 Data Term Rdy (DTR) 23 TTY-RXD Return 25 TTY-RXD Current Loop Input 4. Theory of Operation The data received by the MX-85 is stored in the 4K Byte Memory. Printing is initiated by the following means: 1. Receipt of ...

  • Epson M X - 8 5 - page 28

    4.2. Paper empty The paper empty switch located beneath the platen will activate when the paper runs out. When activated, the following conditions will take place: Status - DTR pin 20 = Mark (-V) Rev Chan pin 11 = Mark (-V) Data Entry - Available until buffer full Indicators - “Paper Out” ON "Ready” OFF Buzzer - Sounds for 20 seconds Pri ...

  • Epson M X - 8 5 - page 29

    5. Paper Tear-Off 1. To tear off the last message printed, depress the FF button to position the paper. 2. Hold down the printer cover while tearing the paper. 3. Check to see that the paper is against the platen and that the paper has not shifted. Reposition if necessary. Tear off the Paper Fig. 21 Cutting Paper -24 - ...

  • Epson M X - 8 5 - page 30

    MAINTENANCE AND PARTS REPLACEMENT Preventative Maintenance of the MX-85 consists mainly of cleaning. 1. Paper dust and particles should be cleared away with a soft brush. 2. The exterior of the Printer can be cleaned with a mild detergent and water solution. 3. The interior of the Printer can be cleaned with denatured alcohol. The only user replace ...

  • Epson M X - 8 5 - page 31

    Head Lock Lever Carriage A&embly Print Head Unit Terminal Board Head Connector Be sure to hold this con- nectar firmly to pull the head cable out straight. (Side View) *Take hold of the cable at the point indicated by arrows force in and apply either of the directions indicated by arrow to push in or pull out the head cable. Fig. 22 Replacement ...

  • Epson M X - 8 5 - page 32

    Appendix A ASCII Code Table b 1 (low order bit) is normally transmitted first. -27 - ...

  • Epson M X - 8 5 - page 33

    Appendix B Baudot Code Table -28 - ...

  • Epson M X - 8 5 - page 34

    Appendix C Character Fonts (Hex. Code) A F NOTE: Numbers represent Hex. -29 - ...

  • Epson M X - 8 5 - page 35

    NOTE: Numbers represent Hex. Code. -30 - ...

  • Epson M X - 8 5 - page 36

    FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT “This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and tele vision reception. It has been type tested and found to comply with ...

メーカー Epson カテゴリー Printer

Epson M X - 8 5のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- M X - 8 5の取扱説明書
- Epsonの製品カード
- パンフレット
- またはEpson M X - 8 5の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Epson M X - 8 5の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Epson M X - 8 5の取り付け説明書、サービスマニュアル、簡易説明書、またはEpson M X - 8 5のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Epson M X - 8 5の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Epson M X - 8 5デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEpson M X - 8 5を使用するのを助ける技術的文書のことです。説明書は通常、全てのEpson M X - 8 5ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Epsonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Epson M X - 8 5の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEpson M X - 8 5の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Epson M X - 8 5に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Epson M X - 8 5デバイスの基本機能を使うにあたってのヒント。 Epson M X - 8 5のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Epson M X - 8 5に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEpson M X - 8 5のメーカー/サービスへの連絡先に関する情報。

Epson M X - 8 5についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもEpson M X - 8 5の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEpson M X - 8 5で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)