-
Harbor Freight Tools 03733 - page 1
4” TILE SA W WITH PVC TRA Y Model 03733 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www.harborfreight.com Cop yright 2003 by Harbor F reight T ools ® . All r ights reser v ed. No por tion of this manual or any ar tw or k contained herein ma y be reproduced in an y shape or f ...
-
Harbor Freight Tools 03733 - page 2
SKU 03733 P A GE 2 PR ODUCT SPECIFICA TIONS Item Description Electri cal Requirements 120 Volt / 60 H z 456 Watts / 4,480 RPM Maximum Cutting Size C apacity 12” L x 12” W x 1-1/16” Thick Blade Type Diamond 4” Continuous Arbor Si ze 5/8” Water Coolant Basi n Capacity 5 Cups, or 40 Ounces Saw B evel Capacity 22.5 Degree and 45 Degree Scale ...
-
Harbor Freight Tools 03733 - page 3
4. DO NO T USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 5. USE EYE & EAR PRO TECTION. Wear an ANSI appro ved, full f ace, saf ety shield and ear protection wh ...
-
Harbor Freight Tools 03733 - page 4
must understand that common sense and caution are factors, which cannot be b uilt into this product, b ut must be supplied b y the operator . SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS 1. MAINT AIN A SAFE W ORKING ENVIR ONMENT . K eep the work area well lit. Make sure there is adequate surrounding w o rkspace. Alwa ys keep the work area free of ob ...
-
Harbor Freight Tools 03733 - page 5
6. KEEP ALL SAFETY GU ARDS IN PLACE, IN PROPER ADJUSTMENT , AND IN PROPER ALIGNMENT . 7. REDUCE THE RISK OF A CCIDENT AL ST ARTING. Mak e sure the P ow e r Switch (part #4) is in the “OFF” position before plugging the Power Cord (par t #11) into a grounded, 3-hole, 120 V olt, electr ical outlet. 8. THIS TILE SA W IS DESIGNED FOR USE ONL Y WITH ...
-
Harbor Freight Tools 03733 - page 6
18. FEED THE WORKPIECE GRADU ALL Y INT O THE TILE SA W BLADE (part #36) WHEN CUTTING. Do not force the machine to remove material faster than it was designed to cut. 19. WHEN CUTTING A LARGE WORKPIECE, MAKE SURE ITS ENTIRE LENGTH IS PROPERL Y SUPPORTED . If necessar y , use a roller stand (not provided) with larger workpieces. 20. NEVER A TTEMPT T ...
-
Harbor Freight Tools 03733 - page 7
PRODUCT DESCRIPTION 1. The Tile Saw f eatures a built-in water supply that k eeps its Tile Sa w Blade cool, reduces dust and debris, and is easy to clean. Its efficient design retur ns water directly to the reservoir and is accurate enough for most ceramic tile, quarry tile, marble, terra cotta, and slate jobs. (See Figure B.) ASSEMBL Y AND OPERA T ...
-
Harbor Freight Tools 03733 - page 8
4. Remov e the old Tile Saw Blade (par t #36), and replace it with a new Tile Saw Blade. NO TE: Make sure to install the new Tile Sa w Blade with the arro w pointing toward the front of the machine. (See Figure C.) 5. Replace the Outer Flange (part #37), and retighten the Nut (part #38) to secure the Tile Saw Blade in place . (See Figure C.) REMO V ...
-
Harbor Freight Tools 03733 - page 9
T o Make Straight Cuts: 1. Remov e the Screw (par t #16). Then, remov e the T ab le (par t #1) from the Tile Saw unit. (See Figure C.) 2. Fill the Body (par t #19) with water . CA UTION: Make sure the water level is high enough to cover the lo wer edge of the Tile Saw Blade (part #36), but not above the maxim um water level as indicated b y the arr ...
-
Harbor Freight Tools 03733 - page 10
8. Place the workpiece to be cut against the Parallel Rip Fence (part #7), and slowly f eed the wor kpiece into the spinning Tile Saw Blade (par t #36). (See Figure B.) 9. When finished making the cut, turn the Power Switch (part #4) to its “OFF” posi- tion and unplug the P ower Cord (par t #11) from its electrical outlet. (See Figure B.) T o M ...
-
Harbor Freight Tools 03733 - page 11
slo wly f eed the wor kpiece into the spinning Tile Saw Blade (par t #36). (See Figure B.) 2. When finished making the angled cut, turn the Power Switch (part #4) to its “OFF” position and unplug the P ow er Cord (par t #11) from its electr ical outlet. (See Figure B.) INSPECTION, MAINTENANCE, AND CLEANING 1. CA UTION: Always turn the P ower Sw ...
-
Harbor Freight Tools 03733 - page 12
P ARTS LIST Part # Descripti o n Q ty. Part # D escr ipti o n Q ty. 1 T abl e 1 21 Angle G auge 1 2 H andl e 1 22 Bench S top 2 3 H andl e B ase 2 23 M otor H ol der (Top) 1 4 P ower Sw i tch 1 24 G uard Stand 1 5 W i re 4 25 Screw (M 4 x 16) 2 6 S cr ew (M 3 x 15) 4 26 M otor H ol der (Bott om ) 1 7 P ar al l el Ri p F ence 1 27 Knob 1 8 B l ade G ...
Harbor Freight Tools 03733についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHarbor Freight Tools 03733の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 03733で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。