Graco 310643uの取扱説明書

18ページ 1.97 mb
ダウンロード

ページに移動 of 18

Summary
  • Graco 310643u - page 1

    310643U EN Repair Displacement Pump Use only genuine Graco replacem ent parts. Use of non-Graco replacement parts may void warranty. 3300 psi (22.7 MPa, 227 bar) Ma ximum Working Pressure Model 248204, Series A UltraMax II and Ultimate MX II 695/795 ASM Zip-Spray 2700 Plus, 3100 Plus ASM AllPro Mach 8600 Plus and 11000 Plus ASM H2700 Plus Model 255 ...

  • Graco 310643u - page 2

    Warnings 2 310643U Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Parts - Pump 248204, 2770 69, 255968 . . . . . . . . . 14 Parts - Pump 248205 , 249057, 24905 9, 277070, 257146 . . . . . . . . . . . . . . . . . . . . . . ...

  • Graco 310643u - page 3

    Service 310643U 3 Service Pressure Relief Procedure Follow the Pressure Relief Pr ocedure whenever you see this symbol. 1. Engage trig ger lock. 2. Turn ON/OFF switch to OFF. 3. Unplug power cord. 4. Disengage trigger lock. Ho ld metal part of gun against grounded metal pail an d trigger gun into pail to relieve pressure. 5. Engage the tr igger loc ...

  • Graco 310643u - page 4

    Service 4 310643U Repair When Pump is Separated From Sprayer Disassembling the Pump 1. Remove packin g nut (202) and o-rin g (228). 2. Unscrew intake va lve from cylinder. 3. Disassemble intake valve. Clean and inspect o-ring (227). NOTE: A pick may be require d to remove o-ring. 4. Tap piston rod out of cylin der with a hammer or flip over and tap ...

  • Graco 310643u - page 5

    Service 310643U 5 6. Unscrew piston valve from piston rod. Clean and inspect parts. The piston has a special thread lock- ing/sealing patch. Do not remove the patch. The patch allows four disassembly/assembly procedur es before it is nece ssary to apply thre ad sealant to the threads. 7. Remove packings and gla nds from piston rod. 8. Remove throat ...

  • Graco 310643u - page 6

    Service 6 310643U 2. Install ball (206 ) in pisto n rod. If th read sealan t is applied to piston valve threads, make sure that non e gets on ball. 3. Tighten piston valve to piston ro d as specified: 4. Soak all leather packing s in SAE 30W oil for one hour minimum prior to assembly. Place male gland (204) in cylinder. Alternate ly stack UHMWPE (2 ...

  • Graco 310643u - page 7

    Service 310643U 7 7. Slide piston a ssembly into bottom of sleeve. 8. Grease top inch or two of piston rod that will go through the cylinder throat packings. 9. Grease o-rings (221) and pla ce on sleeve. Slide sleeve/piston ro d assembly into bottom of cylinder. Replace o-ring (207) if de sired. NOTE: O-ring (207) is not required fo r safe pump ope ...

  • Graco 310643u - page 8

    Service 8 310643U 12. Install intake valve on cylin der. If a wrench is used torque as follows: 13. Torque packing nu t (202) down onto adjustm ent spacer (22 8) 100 + /- 10 in-lb. (11.3 +/- 1.1 N•m) 14. Remove o-ring (22 8) when pump packings begin to leak after extended use. Then tighten packing nu t down until leakage stops or lessens. This al ...

  • Graco 310643u - page 9

    Service 310643U 9 Repair When Pump is On Sprayer 1. Perform Pressure Relief Pro cedure , page 3. 2. Remove intake valve. 3. Push up ret aining spring ( 26). 4. Push out pin (29). 5. Disassemble intake valve. Clean and inspect. O-ring (227) may re quire a pick for remo val. 6. Remove pisto n rod and sleeve. ti4258c ti4258a 26 29 26 ti4258b ti4258b 2 ...

  • Graco 310643u - page 10

    Service 10 310643U 7. Invert piston rod and sleeve and pound on hard sur- face until piston rod comes out of sleeve. Mark IV models: Remove sleeve spacer from sleeve. 8. Remove packin g nut (202 ). 9. Invert piston rod and insert into cylinder to force out throat packings. 10. Insert piston rod into cylinder with pin hole up and piston valve down. ...

  • Graco 310643u - page 11

    Service 310643U 11 14. Remove packings and glands from piston rod. 15. Soak all le ather pack ings in S AE 30W oil fo r one hour minimum prior to assembly. Stack male gland (219) on piston rod. Alternately stack UHMWPE (208 )and leather (218) packings (note orientation) on piston rod. Instal l female gland (217 ). Instal l piston w iper (216) and b ...

  • Graco 310643u - page 12

    Service 12 310643U 18. Slide piston assembly into bottom of sleeve. Make sure V-packing and u- cup are not rolled over or damaged. Mark IV models: Install o-ring (2 31) on sleeve spacer (230). Install sleeve spacer on sleeve. 19. Grease top inch or two of piston rod that will go through the cylinder throat packings. 20. Grease o-ring (221) and plac ...

  • Graco 310643u - page 13

    Service 310643U 13 24. Reassemble intake valve with new o-rings (227) and (230), seat (212) and b all (214). Seat may b e flipped over and used on other side. Cle an seat thoroughly. 25. Install intake valve on cy linder. Torque as follows: Pump Packings Models Torque 248204, 253056, 255968, 277069 70 +/- 5 ft -lb (94.9 + /-6.8 N• m) 248205, 2490 ...

  • Graco 310643u - page 14

    Parts - Pump 2482 04, 277069, 2559 68 14 310643U Parts - Pump 2482 04, 277069, 255968 Series A Ref. Part Descriptio n Qty. 201 179810 SEAL , throat 1 202 193046 NUT, packing 1 203* 192692 V-PACKING , throat, V-Max, UHMWPE, blue 3 204* 15C987 GLAND, male, throat, 1 205 CYLINDER, pump 243346 Model 248204, 255968 1 243346 Model 16X428 1 206* 105444 BA ...

  • Graco 310643u - page 15

    Parts - Pump 2482 05, 249057, 249059, 2 77070, 257146 310643U 15 Parts - Pump 248205, 2490 57, 249059, 277070, 257146 Series A Ref. Part Description Qty. 201  183171 PLUG 1 202 193032 NUT, packing 1 203*  193124 V-PACKING, throat, V-Max, UHMWPE, blue 4 204*  15C989 GLAND, packing, male, throat 1 205 CYLINDER, pump 1 243347 Model 248205, 27 ...

  • Graco 310643u - page 16

    Parts - Pump 253056 16 310643U Parts - Pump 253056 Ref. Part Description Qty. 201*  179810 SEAL, throat 1 202 193046 NUT, packing 1 203*  192692 V-PACKING, throat, V-Max, UHMWPE, blue 3 204*  15C987 GLAND, male, throat 1 205 287876 CYLINDER, pump 1 206* BALL, check 1 105444* BALL, sst, 0.3125 in. (optional) 119259  BALL, ceramic, 0.3125 ...

  • Graco 310643u - page 17

    Technical Data 310643U 17 Technical Data U.S. Metric Maximum Working Pressure 3300 psi 227 bar, 22.7 MPa Fluid Inlet Size 1-5/16-12 un(m) 1-5/16-12 un(m ) Fluid Outlet Size 248204, 255968, 2770 69 1/4 npt(f) 248205, 249057, 249059, 253056, 277070, 257146 3/8 np t(f) Wetted Parts stainless s teel, PTFE, le ather, nylon , zinc-plate d carbon st eel, ...

  • Graco 310643u - page 18

    All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. This manual contains Eng lish. MM 310643 Graco Headquarters: Minne apolis International Offices: Belgium, China, Japan, K ...

メーカー Graco カテゴリー Heat Pump

Graco 310643uのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 310643uの取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco 310643uの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco 310643uの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco 310643uの取り付け説明書、サービスマニュアル、簡易説明書、またはGraco 310643uのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco 310643uの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco 310643uデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco 310643uを使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco 310643uユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco 310643uの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco 310643uの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco 310643uに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco 310643uデバイスの基本機能を使うにあたってのヒント。 Graco 310643uのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco 310643uに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco 310643uのメーカー/サービスへの連絡先に関する情報。

Graco 310643uについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco 310643uの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco 310643uで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)