日本語 dropdown-ico

Toshiba IK-DF02Aの取扱説明書

24ページ 1.56 mb
ダウンロード

ページに移動 of 24

Summary
  • Toshiba IK-DF02A - page 1

    INSTRUCTION MANU AL DOME CAMERA ZEIM-4000100G A.1 IK-DF02A T ABLE OF CONTENTS IMPOR T ANT SAFEGU ARDS ........................................ 1 1. FEA TURES AND DESCRIPTION ................................. 4 2. COMPONENTS ............................................................ 4 3. P AR T NAMES AND FUNCTIONS ................................ ...

  • Toshiba IK-DF02A - page 2

    - 1 - 1. Read Instructions All the safety and operating instructions should be read before the product is oper ated. 2. Retain Instructions The safety instructions and instruction manual should be retained for future ref erence. 3. W arnings Comply with all warnings on the product and in the instruction manual. 4. Follow Instructions F ollo w all o ...

  • Toshiba IK-DF02A - page 3

    - 2 - • The CA UTION label, shown on the left, is attached on the camera. CA UTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NO T REMO VE COVER (OR BA CK). NO USER SER VICEABLE P ARTS INSIDE. REFER SER VICING T O QU ALIFIED SERVICE PERSONNEL. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to aler t the user ...

  • Toshiba IK-DF02A - page 4

    - 3 - Disclaimer We disclaim any responsibility and shall be held harmless f or any damages or losses incurred by the user in any of the f ollowing cases: 1. Fire, earthquake or any other act of God; acts by third parties; misuse b y the user, whether intentional or accidental; use under extreme operating conditions . 2. Malfunction or non-function ...

  • Toshiba IK-DF02A - page 5

    - 4 - 1. FEA TURES AND DESCRIPTION 1. 24V AC/12V DC dual-v oltage capability extends power options . 2. Camera has the ability to automatically switch to color in da ylight or black and white at night. 3. Camera synchronization mode is selectable between internal and line lock. 4. Back Light Compensation (BLC) adjusts f or strong backlight conditio ...

  • Toshiba IK-DF02A - page 6

    - 5 - 1 ON OFF 234 3. P AR T NAMES AND FUNCTIONS P an ADJ Scre w Tu rn the ring-type screw to adjust the lens pan angle. F asten and lock it after completing the adjustment. Po wer Input Wire Connect the power cable to 24V A C or 12V DC. Length: approx. 12 inches (300mm) Video Wire (BNC T ap) Connect the video cable to a monitor or video de vice. T ...

  • Toshiba IK-DF02A - page 7

    - 6 - 4. CONNECTIONS •P ow er plugs of connected equipment must be disconnected bef ore camera installation. •A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required f or standard connection. •F or details of wir ing and oper ation of equipment to be connected, refer to their operation manuals . •A power supply with cab le, conne ...

  • Toshiba IK-DF02A - page 8

    - 7 - 4-2. Line lock Contr ol • Matching the vertical synchronization with the power frequency is called the Line Loc k. •T o activate the line loc k, set the LL switch to ON. • When two or more cameras are s witched by the video switcher f or viewing with a displa y monitor the vertical synchronization phase can be lock ed to the power frequ ...

  • Toshiba IK-DF02A - page 9

    - 8 - Upside P 5. INST ALLA TION Note: The attached screws are used to install the camer a to a solid surf ace. If installing to surfaces of loose or thin materials, use the appropriate anchors (not included) with the screws. 5-1. Installing the Camera 5-1-1. T amper Resistant Feature 1. To remov e the cov er, rotate the cov er counter clockwise . ...

  • Toshiba IK-DF02A - page 10

    - 9 - Upside T o Determine Whic h Set of Mounting Holes to Use Mounting Holes (i) • Installation to a wall or ceiling. (Refer to section 5-1-2.) • Installation to a switch bo x positioned normally on a wall. (Refer to section 5-1-3 (i).) • Installation to a switch bo x attached to a ceiling. (Refer to section 5-1-3 (i) f or s witch bo x orien ...

  • Toshiba IK-DF02A - page 11

    - 10 - 5-1-2. Installation to a Wall or Ceiling To mount the camer a directly on the wall or ceiling. 1. Prepare the mounting space. 2. Place the camera on the wall or ceiling and mark four scre w positions with a pen. 3. Attach the camera with the f our screws to the w all or ceiling. 4. F asten all the screws. (i) Rerouting the Wires for Flush Mo ...

  • Toshiba IK-DF02A - page 12

    - 11 - B: Routing the Wires to the Left Side 1. Remov e the wires from the wire hole and position them to the left of the base. 2. Firmly secure the wires with the wire tie. Do not over tighten the wire tie. Wire Tie Wire Hole (ii) Notching Out a Hole f or the Wires • Cut out the knock out, "A" f or the r ight side or "B" f or ...

  • Toshiba IK-DF02A - page 13

    - 12 - 1.81(46) Dimensions: inch (mm) 3.29(83.5) Upside 5-1-3. Installation to a Switch Bo x (i) Mounting the Camera to a Switch Bo x Positioned Normall y on a W all 1. Install the s witch box. 2. Set the "Upside" on the base to the up position. 3. Attach the camera to the s witch box with the f our mounting screws. Mounting Screw x 4 (no ...

  • Toshiba IK-DF02A - page 14

    - 13 - 1.81(46) Dimensions: inch (mm) 3.29(83.5) Upside (ii) Mounting the Camera to a Switch Bo x Positioned Side ways 1. Install the s witch box positioned side ways on a wall. 2. Attach the f our mounting screws to the s witch bo x. 3. P ositioning the "Upside" at the top, mo ve the screws through the base and turn the base clockwise. 4 ...

  • Toshiba IK-DF02A - page 15

    - 14 - (iii) Mounting the Camera to a Switch Bo x Attached to a Ceiling 1. P osition the cover to conceal the unlock-b utton from the visible side. 2. Use the mounting holes (i) or (ii) depending on the direction of the s witch bo x. (Refer to section 5-1-3 (i) or (ii).) 3. Attach the camera to the s witch box with the f our mounting screws. Ceilin ...

  • Toshiba IK-DF02A - page 16

    - 15 - 5-2. Adjusting the Viewing Angle (1) T o check the video image on the monitor , connect the "Monitor Out Harness Wire" to the connector "MON". (2) The lens pan direction can be adjusted by turning pan lock 1 counter cloc kwise to loosen it without moving the lens. Retighten after adjusting. (3) Tilt angle of the lens can ...

  • Toshiba IK-DF02A - page 17

    - 16 - 7. LINE LOCK PHASE If two or more cameras within a system ha ve diff erent AC line phases and the y are switched by a video s witcher , the picture on the display monitor will fluctuate v er tically . Connect 24V A C input lines of all cameras so that they all share the same phase . If you still ha ve v er tical fluctuation, adjust the V PHA ...

  • Toshiba IK-DF02A - page 18

    - 17 - 8. NO TES ON USE AND INST ALLA TION • Do not aim the camera at the sun Nev er aim the camera at the sun ev en with the camera power off . • Do not shoot intense light Intense light such as a spotlight ma y cause a bloom or smear . A vertical str ipe ma y appear on the screen. Howe ver , this is not a malfunction. •T reat the camera wit ...

  • Toshiba IK-DF02A - page 19

    - 18 - 9. IN CASE OF PR OBLEMS Condition No image Unnatural color The image is out of f ocus . The image is dark. Check P oints • Are the camera and connected equipment turned on? • Is the mode setting s witch DC/AES set to OFF? Be sure to set to ON. • Are wires connected correctly? • Is the displa y monitor adjusted correctly? • Is the l ...

  • Toshiba IK-DF02A - page 20

    - 19 - 1. Image System Image De vice Pixel Elements 2. Electrical TV System Horizontal Resolution S/N Ratio Minimum Illumination A uto Gain Control (A GC) Iris Control Mode White Balance White Balance Range Gamma compensation Backlight Compensation (BLC) Video Output Signal Synchronization System 3. Mechanical W eight Dimension 4. Optical Built-in ...

  • Toshiba IK-DF02A - page 21

    - 20 - 11. EXTERIOR VIEW 1.81 (46) (1.81 (46)) 2.05 (52) 0.05 (1.2) 3.94 (100) 3.99 (101.2) 3.29 (83.5) (3.29 (83.5)) Dimensions: inch (mm) 5.08 (129) 5.08 (129) ...

  • Toshiba IK-DF02A - page 22

    - 21 - 1.81 (46) 1.81 (46) 3.94 (100) depth about 1.58 (40) 3.29 (83.5) Dimensions: inch (mm) Screw ( 0.18 (4)) x4 - TP4 x37 W all ...

  • Toshiba IK-DF02A - page 23

    - 22 - MEMO ...

  • Toshiba IK-DF02A - page 24

    LIMITED W ARRANTY CCD SECURITY CAMERA IK-DF02A The Imaging System Division ("ISD") of T oshiba America Information Systems, Inc. makes the f ollowing limited warranties with regard to this CCD Camera Model IK-DF02A ("Product"). These limited w arranties extend to the Original End-User ("Y ou[r]"). Three (3) Y ear Limit ...

メーカー Toshiba カテゴリー Security Camera

Toshiba IK-DF02Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- IK-DF02Aの取扱説明書
- Toshibaの製品カード
- パンフレット
- またはToshiba IK-DF02Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Toshiba IK-DF02Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Toshiba IK-DF02Aの取り付け説明書、サービスマニュアル、簡易説明書、またはToshiba IK-DF02Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Toshiba IK-DF02Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Toshiba IK-DF02Aデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがToshiba IK-DF02Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのToshiba IK-DF02Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Toshibaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Toshiba IK-DF02Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははToshiba IK-DF02Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Toshiba IK-DF02Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Toshiba IK-DF02Aデバイスの基本機能を使うにあたってのヒント。 Toshiba IK-DF02Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Toshiba IK-DF02Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるToshiba IK-DF02Aのメーカー/サービスへの連絡先に関する情報。

Toshiba IK-DF02Aについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもToshiba IK-DF02Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがToshiba IK-DF02Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)