Weber FT 600の取扱説明書

48ページ 1.3 mb
ダウンロード

ページに移動 of 48

Summary
  • Weber FT 600 - page 1

    Serial Number Please use this number in registering your warranty and any correspondence with the factory . FT 600 LP Gas Barbecue Owners’ Manual 96619 4/96 E F National Association PROPANE GAS ® W ARNING: Do not try to light this appliance without reading "Lighting" instructions section of this manual. THIS GAS APPLIANCE IS DESIGNED F ...

  • Weber FT 600 - page 2

    2 W ARNINGS Do not store a spare or disconnected LP tank under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas leaks and burner obstructions before using. See instructions in this ma ...

  • Weber FT 600 - page 3

    3 W ARRANTY Weber-Stephen Products Co. (W eber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue that it will be free of defects in material and workmanship from the date of purchase as follows: Aluminum Castings, 10 years, Stainless Steel Flavorizer Bars, 5 years, Cooking Grill, 3 years, Cast Iron Griddle, 1 year , All Remainin ...

  • Weber FT 600 - page 4

    © 1996 Weber-Stephen Products Co. W eber , , Flavorizer and Crossover are registered U.S. trademarks; Gas Catcher is a trademark of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266, U.S.A. W eber is also a registered trademark (Reg. TM., Marca Registrada, Marque Desposee, Schutzmarke) in Canada, Germany , France, Italy , ...

  • Weber FT 600 - page 5

    5 Contents W ARNINGS ..................................................................2 W arranty & Patents .................................................. 3-4 General Instructions .................................................... 6 Assembly ................................................................ 7-29 Operating Instructions Ligh ...

  • Weber FT 600 - page 6

    6 General Instructions The Weber Gas Barbecue is a portable outdoor cooking appliance. With your Weber Gas Barbecue you can grill and barbecue with results that are difficult to duplicate with indoor kitchen appliances. The Weber Gas Barbecue is portable so you can easily change its location in your yard or on your patio. Portability means you can ...

  • Weber FT 600 - page 7

    7 Step 1 Check package contents Cooking box (assembly) Wheel frame Caster frame Bottom connectors (2) Back panel T op frame rail #1’s (2) T op frame rail #2’s (2) Splash guards (2) Assembly T ools needed Hammer 7/16 inch open end or an adjustable wrench Pliers Block of wood Phillips screwdriver Regular screwdriver Supplies needed Y our LP tank ...

  • Weber FT 600 - page 8

    8 T ank panel assembly Fuel scale assembly Catch pan holder Catch pan Aluminum drip pans (2) Wheels (2) Accessory rack LP tank LP tank filler adapter Right work surface Left work surface Bottom tray Flavorizer bar / Cooking grill holders (2) Cooking grills (2) Griddle Flavorizer bars (1 1) W E B E R W E B E R W E B E R W E B E R ...

  • Weber FT 600 - page 9

    9 Wheel hubcaps (3) (one is a spare) (actual size) Plastic button (actual size) Casters (2) Match holder bracket 1/4-20 x 5/8 screw (actual size) Check contents of hardware packs Glides (4) 1/4-20 x 3 1/2 inch bolts (4) (actual size) 1/4-20 x 1 3/4 inch bolt (actual size) 1/4-20 x 1/2 inch bolts (6) (actual size) Phillips head 1/4-20 x 1 inch machi ...

  • Weber FT 600 - page 10

    10 Step 2 Assemble wheel frame Y ou will need: wheel frame, two wheels, two wheel hubcaps, hammer and a block of wood. Note: Work on a carpeted area (on grass, or on one of the boxes) to protect the finish during the frame assembly . Set one end of wheel frame on the block of wood (or other hard, protected surface). Put one wheel on axle, WEBER sid ...

  • Weber FT 600 - page 11

    11 Step 4 Continue frame assembly Y ou will need: Wheel frame, caster frame, two bottom connectors, four 1/4-20 x 3 1/2 inch bolts, four nylon washers and a 7/16 inch or adjustable wrench. T urn caster frame and wheel frame upside down, and space apart. Figure 3. Note: Fuel scale decal on wheel frame must be on the back side. Hold one bottom connec ...

  • Weber FT 600 - page 12

    12 Step 6 Assemble front top frame rail Y ou will need: one top frame rail #1, one top frame rail #2, one 1/4-20 x 1/2 inch bolt, frame assembly and 7/16 inch or adjustable wrench. Put top frame rail #1 to your right and top frame rail #2 to your left. Figure 6. Insert top frame rail #1 into top frame rail #2. Figure 6 (a). Insert the bolt. Figure ...

  • Weber FT 600 - page 13

    (a) Fuel scale decal on front side T op frame rail assembly Cut out View from the back Front caster frame Front wheel frame Position the top frame rail assembly with the tabs to the inside of the cart. Figure 7 (a). Insert the tabs into the front caster frame and front wheel frame, the round tubing of the top frame rail assembly will rest in the cu ...

  • Weber FT 600 - page 14

    14 Step 8 Bolt front top frame rail assembly Y ou will need: two 1/4-20 x 1/2 inch bolts, two nylon washers, frame assembly and 7/16 or adjustable wrench. Slip a washer over the bolt. Insert the bolt from the inside of the frame assembly into the caster frame. Figure 10 (a). Align the hole in the tab of the top frame rail assembly and start the bol ...

  • Weber FT 600 - page 15

    15 Step 9 Bolt back panel and back top frame rail assembly Y ou will need: back panel, two nylon washers, two 1/4-20 x 1/2 inch bolts and frame assembly . Position back panel cut outs to the top and the flanges to inside of the frame assembly . Figure 1 1 (a). Figure 1 1 Figure 12 (a) (a) Wheel frame Flange Cut out Caster frame Align hole of back p ...

  • Weber FT 600 - page 16

    16 Step 10 Add tank panel Y ou will need: tank panel assembly , 1/4-20 x 1 3/4 inch bolt, 1/4-20 hex nut, two 1/4 inch nylon washers, pliers, and a 7/16 inch or adjustable wrench. Insert the tank panel tabs into the slots in the wheel frame brace. Slide up until the notch at the bottom of the tank panel fits over the cross brace of wheel frame. Fig ...

  • Weber FT 600 - page 17

    17 Figure 15 Figure 16 (a) Flanges Cooking box assembly Control panel Step 12 Add cooking box assembly Y ou will need: frame assembly and cooking box assembly . Note: This assembly takes two people to lift the cooking box assembly into the frame. Uncoil the hose. Set the cooking box into the frame so the control panel is under the top frame rail. F ...

  • Weber FT 600 - page 18

    Front edge of the control panel 18 Step 13 Remove the control panel and the front panel T ake off all 6 burner control knobs. Pull up on the ignition buttons until they stay in the up position. Figure 17. Put your fingers under the front edge of the control panel and lift up and pull evenly toward you. Figure 19 (a). The control panel is separate f ...

  • Weber FT 600 - page 19

    19 Step 14 Check burner alignment Y our Weber Gas Barbecue burner assembly has been factory assembled, pressure and flame tested. As a safety precaution we recommend you check the burner alignment. Figure 21. a) Are the mounting clips that hold the manifold and burner assembly in place? Figure 21 (a). b) Do the valves fit into the ends of the burne ...

  • Weber FT 600 - page 20

    20 Step 16 Fill LP tank Note - The LP tank manufacturer is responsible for the materials, workmanship and performance of the tank. If the tank has a defect, malfunctions, or you have a question regarding the tank, call the tank manufacturer's customer service center . The phone number is on the warning decal which is permanently attached to th ...

  • Weber FT 600 - page 21

    21 The hose and regulator are connected in the following manner: Slide back the collar of the quick disconnect on the tank valve. Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 26 (a). Figure 26 (b) shows the quick disconnect engaged and various components of the tank and reg ...

  • Weber FT 600 - page 22

    Manifold Figure 28 22 Step 19 Check for gas leaks  DANGER  Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for leaks. This will result in a fire or explosion which can cause serious bodily injury or death and damage to property . Check for leaks by wetting the connections ...

  • Weber FT 600 - page 23

    23 Step 20 Install Flavorizer Bar/cooking grill support Y ou will need: two Flavorizer Bar/cooking grill supports. Slide one Flavorizer Bar/cooking grill support behind the bracket in the rear of the cooking box assembly . Figure 29 (a). Slide the second Flavorizer Bar/cooking grill support behind the brackets at the front of the cooking box assemb ...

  • Weber FT 600 - page 24

    24 Step 22 Install splash guards Y ou will need: two splash guards Position splash guard, flanges to the rear , at the back of the cooking box assembly . Figure 31 (a). Insert both wire ends into the mounting holes in the cooking box. Figure 31. Note: Y ou will have to bend the splash guards slightly to fit into the mounting holes. Position the sec ...

  • Weber FT 600 - page 25

    25 The open “U” of the cooking grill goes down. Set both cooking grills in place next to the griddle. Figure 35. Figure 34 Figure 35 Step 23 Install Cooking Grills and Griddle Y ou will need: two cooking grills and one griddle. Set the griddle on top of the Flavorizer Bar/cooking grill support. Figure 34.  CAUTION: The drain hole of the grid ...

  • Weber FT 600 - page 26

    26 Step 24 Install left work surface and glides Y ou will need: left work surface, two nylon (plastic) glides, two Phillips head 1/4-20 x 1 inch machine screws and a Phillips screwdriver . Set the left work surface over the top of the cooking box and the top frame rails. Figure 36. The left work surface will cover half of the handles on the left si ...

  • Weber FT 600 - page 27

    27 Step 26 Reinstall front panel, control panel and burner control knobs Y ou will need: control panel, front panel, and four burner control knobs. With the Weber logo to the left, slide front panel down into place. Figure 38. Figure 38 Figure 39 (a) Figure 40 Push on the burner control knobs. Figure 40. Pull igniter buttons up until they stay in t ...

  • Weber FT 600 - page 28

    28 Step 27 Install bottom tray Y ou will need: Bottom tray , catch pan holder , catch pan, and one drip pan. Figure 41 Figure 42 Figure 43 Figure 44 Note: It may be easier to install the catch pan holder by removing the catch pan from the holder . Hook the ends of the catch pan holder into the hole in the bottom tray . Figure 42. Slide the bottom t ...

  • Weber FT 600 - page 29

    29 Step 28 Add accessory rack Y ou will need: accessory rack. Set the bottom rack between the two bottom connectors. Figure 45. Figure 45 ...

  • Weber FT 600 - page 30

    30 1) Open the sliding work surfaces and splash guards. Figure 1. 2) Check that the fuel scale reads more than “E”. Note - E = empty; F = full. 3) Make sure all burner control knobs are OFF . (Push each burner control knob down and turn clockwise.)  W ARNING: The burner contr ol knobs must be in the OFF position before turning on the LP tank ...

  • Weber FT 600 - page 31

    31 Manual Lighting EA CH HEA T ZONE OPERA TES INDEPENDENTL Y . 1) Open the sliding work surfaces and splash guards. Figure 2. 2) Check that fuel scale reads more than “E”. Note - E = empty; F = full. 3) Make sure all burner control knobs are turned OFF . (Push each burner control knob down and turn clockwise.)  W ARNING: The burner contr ol ...

  • Weber FT 600 - page 32

    32 Cooking The W eber Gas Barbecue should not be moved when operating or hot. Y ou can adjust the LEFT and RIGHT burners as desired. The control settings High (H), Medium (M), Low (L), or Off (O) are described in your W eber cookbook. The cookbook uses these notations to describe the settings of the LEFT and RIGHT burners. Note: Cooking conditions ...

  • Weber FT 600 - page 33

    33 P eriodic Cleaning  CA UTION: T urn your W eber Gas Barbecue OFF and wait for it to cool bef ore cleaning.  CA UTION: Do not clean your Fla vorizer Bar s or cooking grills in a self-cleaning o ven.Replacement cooking grills and griddles and Flav oriz er Bar s are av ailable through y our retailer . Outside surfaces - Use a warm soapy water ...

  • Weber FT 600 - page 34

    34 Scale setting wing nut T ank lock wing nut T ank valve Collar (a) (b) Figure 4 Refilling the LP tank We recommend that you refill before the scale indicator reaches "E". Note - If you run out of fuel, chec k the indicator setting and/or adjust the fuel scale indicator setting with the scale setting wing nut, while the tank is empty so ...

  • Weber FT 600 - page 35

    35 c) Connect the hose to the tank. Route the hose so it does not interfere with the scale indicator rod. Slide back the collar of the quick disconnect on the tank valve. Figure 6 (a). Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 6 (b). If it does not engage or lock, repeat ...

  • Weber FT 600 - page 36

    36 Safe handling tips f or LP Gas ■ Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas. LP gas is a gas at regular temperatures and pressures. Under moderate pressure, inside a cylinder , LP gas is a liquid. As the pressure is released the liquid readily vaporizes and becomes gas. ■ LP gas has an odor similar to natu ...

  • Weber FT 600 - page 37

    37  W ARNING: Y ou should check f or gas leaks every time you disconnect and reconnect a gas fitting. Note: All f actor y made connections hav e been thoroughly check ed f or gas leaks. The burners hav e been flame tested. As a saf ety precaution you should recheck all fittings f or leaks before using y our Weber Gas Barbecue. Shipping and handl ...

  • Weber FT 600 - page 38

    The Weber Spider Stopper Guard is factory installed. It fits tightly around the air shutter section of the burner tube and the valve, thereby preventing spiders and other insects access to the burner tubes through the air shutter openings. Figure 12. W e recommend that y ou inspect the Weber Spider Stopper Guards at least once a y ear . (See Sectio ...

  • Weber FT 600 - page 39

    Main Burner Flame P attern The Weber Gas Barbecue burners have been factory set for the correct air and gas mixture. The correct flame pattern is shown in Figure 13. If the flames do not appear to be uniform the length of the burner tube, follow the burner cleaning procedures. Main Burner Cleaning Procedure T urn off the gas supply . Remove the man ...

  • Weber FT 600 - page 40

    40 12. Slide the burner assembly from each Heat Zone. The left and right burners are connected by the Crossover tube. Figure 20(a). Figure 20 Crossover tube Pull out of here 10. Unlatch the Spider Stopper Guards and remove. Figure 18. Figure 18 Manifold 1 1. Pull the manifold out of the burners. Figure 19. Figure 19 ...

  • Weber FT 600 - page 41

    41 Crosso ver Ignition System Operations If the Crossover Ignition System fails to ignite the Front burner , light the Front burner with a match. If the Front burner lights with a match, then check the Crossover Ignition System. ■ Check that both the white and black ignition wires are attached properly . Figure 24. ■ Check that the Crossover Ig ...

  • Weber FT 600 - page 42

    42 Prob lem Burners b urn with a yellow or orange flame, in conjunction with the smell of gas. Burners do not light. -or - Burners ha ve a small flickering flame in the HIGH position. -or - Barbecue temperature only reaches 250˚ to 300˚ degrees in the HIGH position. Burner does not light, or flame is low in HIGH position. Experiencing flare-ups: ...

  • Weber FT 600 - page 43

    43 ...

  • Weber FT 600 - page 44

    44 1 2 4 5 6 8 7 15 22 23 16 28 30 32 35 36 37 38 57 58 59 56 55 47 46 45 44 43 29 25 48, 39 9-13 14 17 18 21 19 3 27 24 26 33 20 W E B E R W E B E R 34 31 39 49 51 52 39, 40 41 42 50 53 54 ...

  • Weber FT 600 - page 45

    45 1 Cooking grills (2) 2 Griddle 3 Flavorizer bars (1 1) 4 Left work surface 5 Glides (4) 6 Phillips head 1/4-20 x 1 inch machine screws (4) 7 Cooking box (assembly) 8 Burner control knobs (6) 9 Igniter (3) 10 Igniter lock nut (3) 1 1 Igniter wire (black) (3) 12 Igniter wire (white) (3) 13 Gas catcher ignition chamber (3) 14 Manifold mounting clip ...

  • Weber FT 600 - page 46

    46 ...

  • Weber FT 600 - page 47

    47 ...

  • Weber FT 600 - page 48

    A F INAL W ORD OF T HANKS hank you for choosing a W eber Barbecue. Our family her e at W eber has worked har d to pr oduce the highest quality products for your satisfaction. While we give much attention to our pr oducts, an occasional err or may occur . Our knowledgeable Customer Service staff is pr epared to help you with any pr oblems with parts ...

メーカー Weber カテゴリー Gas Grill

Weber FT 600のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- FT 600の取扱説明書
- Weberの製品カード
- パンフレット
- またはWeber FT 600の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Weber FT 600の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Weber FT 600の取り付け説明書、サービスマニュアル、簡易説明書、またはWeber FT 600のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Weber FT 600の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Weber FT 600デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWeber FT 600を使用するのを助ける技術的文書のことです。説明書は通常、全てのWeber FT 600ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Weberの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Weber FT 600の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWeber FT 600の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Weber FT 600に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Weber FT 600デバイスの基本機能を使うにあたってのヒント。 Weber FT 600のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Weber FT 600に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWeber FT 600のメーカー/サービスへの連絡先に関する情報。

Weber FT 600についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWeber FT 600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWeber FT 600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)