Makita BSS730の取扱説明書

24ページ 0.25 mb
ダウンロード

ページに移動 of 24

Summary
  • Makita BSS730 - page 1

    INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Cor dless Cir cular Sa w Equipped with Electric Blade Brake 185 mm (7-1/4”) MODEL BSS730 001324 ...

  • Makita BSS730 - page 2

    2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA003-1 (FOR All BA TTER Y OPERA TED T OOLS ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic sh ...

  • Makita BSS730 - page 3

    3 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pow e r tools create sparks which may ignite the dust or fumes. 3. Keep bystander s, children, and visitors awa y while operating a power tool. Distrac- tions can cause you to lose control. Electrical Safety 4. A battery operated ...

  • Makita BSS730 - page 4

    4 operation. If damaged, have the tool ser- viced before using. Many accidents are caused by poorly maintained tools. 20. Use only accessories that are recom- mended by the manufacturer f or your model. Accessories that may be suitab le for one tool may create a risk of injury when used on another tool. SER VICE 21. T ool service must be performed ...

  • Makita BSS730 - page 5

    5 5. Alwa ys observe that the lower guard is covering the blade bef ore placing saw down on bench or floor . An unprotected, coasting blade will cause the sa w to walk backw ards, cutting whatev er is in its path. Be aw are of the time it takes for the b lade to stop after switch is released. 6. NEVER hold piece being cut in your hands or across y ...

  • Makita BSS730 - page 6

    6 Do not use dull or damaged blade. Unsharpened or improper ly set blades pro- duce narrow k erf causing excessive friction, blade binding and KICKBA CK. Keep b lade sharp and clean. Gum and wood pitch hard- ened on blades slo ws saw and increases potential fo r kickback. K eep blade clean b y first removing it from tool, then cleaning it with gum ...

  • Makita BSS730 - page 7

    7 clamp it do wn. DO NOT TR Y T O HOLD SHORT PIECES BY HAND! 18. Never attempt to sa w with the circular saw held upside down in a vise. This is extremel y dang er ous and can lead to seri- ous accidents. 19. W ARNING: Blade coasts to stop after switch is released. Contact with coasting blade can cause serious injury . Before setting the tool down ...

  • Makita BSS730 - page 8

    8 IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER & B A TTER Y CAR TRIDGE USC002-3 1. SA VE THESE INSTRUCTIONS- This man- ual contains important safety and operat- ing instructions for battery charger . 2. Before using battery char g er , read all instructions and cautionary markings on (1) battery charger , (2) battery , and (3) product using bat ...

  • Makita BSS730 - page 9

    9 ADDITIONAL SAFETY R ULES FOR CHARGER & B A TTER Y CAR TRIDGE 1. Do not charge Battery Cartridge when temperature is BELO W 10°C (50°F) or ABO VE 40°C (104°F). 2. Do not attempt to use a step-up trans- former , an engine g enerator or DC power receptacle. 3. Do not allow an ything to cover or clog the charger vents. 4. Do not short the bat ...

  • Makita BSS730 - page 10

    10 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge. • T o remove the battery car tr idge , ...

  • Makita BSS730 - page 11

    11 6. After charging, unplug the charger from the power source. NO TE: • The batter y charger is f or charging Makita batter y car tridge. Ne ver use it f or other pur poses or f or other manuf acturer ’ s batteries. • When you charge a ne w batter y car tridge or a batter y car tridge which has not been used for a long period of time, it ma ...

  • Makita BSS730 - page 12

    12 • Alwa ys keep clean the v ent on charger and batter y f or cooling. • The products should be sent to repair or maintenance, if the yello w warning light will frequently flash. Conditioning charge Conditioning charge can e xtend the life of battery by auto- matically searching the optimum charging condition f or the batteries in ev er y situ ...

  • Makita BSS730 - page 13

    13 Adjusting depth of cut CA UTION: • After adjusting the depth of cut, alwa ys tighten the lev er securely . Loosen the le ver on the side of the rear handle and mov e the base up or down. At the desired depth of cut, secure the base by tightening the le ve r. F or cleaner , safer cuts, set cut depth so that no more than one blade tooth projects ...

  • Makita BSS730 - page 14

    14 Switch action CA UTION: • Bef ore inser ting the batter y car tridge into the tool, alwa ys check to see that the s witch trigger actuates properly and retur ns to the “ OFF ” position when released. T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided. T o star t the tool, push in the lock- off bu ...

  • Makita BSS730 - page 15

    15 T o install the blade, f ollow the remov al procedure in rev erse. BE SURE T O TIGHTEN THE HEX BOL T CLOCKWISE SECUREL Y . When changing blade , make sure to also clean upper and lower b lade guards of accumulated sawdust. Such eff or ts do not, howe v er, replace the need to chec k lower guard oper a- tion befo re each use. Hex wrench stora ge ...

  • Makita BSS730 - page 16

    16 Hold the tool firmly . The tool is provided with both a front grip and rear handle. Use both to best gr asp the tool. If both hands are holding saw , they cannot be cut b y the blade. Set the base on the workpiece to be cut without the blade making any contact. Then turn the tool on and wait until the b lade attains full speed. Now simply mo ve ...

  • Makita BSS730 - page 17

    17 Adjusting for accurac y of 90 ° and 45 ° cut (vertical and 45 ° cut) This adjustment has been made at the f actor y . But if it is off , adjust the adjusting screws with a he x wrench while inspect- ing 90 ° or 45 ° the blade with the base using a triangular rule or square rule, etc. Replacing carbon brushes Remov e and check the carbon bru ...

  • Makita BSS730 - page 18

    18 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. If you need an y assistance for more details regarding ...

  • Makita BSS730 - page 19

    Memo 19 ...

  • Makita BSS730 - page 20

    Memo 20 ...

  • Makita BSS730 - page 21

    21 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7 ...

  • Makita BSS730 - page 22

    22 Y our answer s to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Under 19 20-29 30-39 40-49 Over 50 P aste Paste P aste Paste P aste P aste Paste P aste P aste Paste P aste Paste P aste P aste P aste Paste P aste Paste ...

  • Makita BSS730 - page 23

    23 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Package carefully and send prepaid to ...

  • Makita BSS730 - page 24

    Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s ...

メーカー Makita カテゴリー Cordless Saw

Makita BSS730のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BSS730の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita BSS730の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita BSS730の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita BSS730の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita BSS730のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita BSS730の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita BSS730デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita BSS730を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita BSS730ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita BSS730の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita BSS730の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita BSS730に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita BSS730デバイスの基本機能を使うにあたってのヒント。 Makita BSS730のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita BSS730に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita BSS730のメーカー/サービスへの連絡先に関する情報。

Makita BSS730についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita BSS730の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita BSS730で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)