Cal Spas A726Lの取扱説明書

32ページ 1.6 mb
ダウンロード

ページに移動 of 32

Summary
  • Cal Spas A726L - page 1

    ...

  • Cal Spas A726L - page 2

    Copyright 2008 Lloyds Material Supply , Inc. All rights reserved. Duplication with- out written consent is strictly prohibited. Cal Spas ® is a registered trademark. Due to continuous improvement pro- grams, all models, operation, and/or specications are subject to change with - out prior notice. L TR20081024, Rev . B 6/12/08 CONTACT INFORMATIO ...

  • Cal Spas A726L - page 3

    1 Pre-Delivery and Installation Checklist Most cities and counties require permits for exterior construction and electrical circuits. In addition, some communities have codes requiring residential barriers such as fencing and/or self-closing gates on property to prevent unsupervised access to the property by children under the age of 5. Y our deale ...

  • Cal Spas A726L - page 4

    2 Planning the Best Location Safety rst Do not place your spa within 10 feet (3 m) of overhead power lines. Make sure the spa is positioned so that access to the equipment compartment and all side panels will not be blocked. Be certain that your installation will meet all city and local safety codes and requirements. Consider how you will use yo ...

  • Cal Spas A726L - page 5

    3 Allow for service access Many people choose to install a decorative structure around their spa. If you are installing your spa with any type of structure on the outside, such as a gazebo, remember to allow access for service. It is always best to design special installations so that the spa can still be accessed. Consider the best place for the o ...

  • Cal Spas A726L - page 6

    4 Portable Spa Site Preparation Y our spa needs a solid and level foundation. The area that it sits on must be able to support the weight of the spa, with water and the occupants who use it. If the foundation is inadequate, it may shift or settle after the spa is in place, causing stress that could DAMAGE YOUR SP A SHELL AND FINISH. Note: Damage ca ...

  • Cal Spas A726L - page 7

    5 The spa must be properly back-lled with wet sand, underneath and • on all four sides. The nal architecture must include permanent ground coverage within • a 10 feet radius of the spa. Never place any spa in a sealed area. W ater must be able either to be • absorbed into the surrounding area or channeled away . W ater build- up under a ...

  • Cal Spas A726L - page 8

    6 Getting the Spa Into Y our Y ard Check the Dimensions of Y our New Cal Spa ® The Cal Spas ® specication chart lists your spa’s model and its dimension as it sits on the delivery cart. During delivery , the spa must remain on the delivery cart at all times. Compare the dimensions to the width of the gates, sidewalks, and doorways along the ...

  • Cal Spas A726L - page 9

    7 Are there protruding gas meters, water meters or A/C units on your • home which will cause obstructions along the delivery path to your yard? Are there stairs in your delivery route? If so, you must consult your Cal • Spas ® dealer prior to delivery to make adequate preparations. Special Circumstances The use of a crane for delivery and inst ...

  • Cal Spas A726L - page 10

    8 Electrical Requirements Electrical Requirements – US and Canada 240 V olt Electrical Installation All 240V spas must be permanently connected (hardwired) to the power supply . These instructions describe the only acceptable electrical wiring procedure. Spas wired in any other way will void your warranty and may result in serious injury . This i ...

  • Cal Spas A726L - page 11

    9 Spa Model GFCI Required Wires Required Portable Spas All 240V spas (except 6300 control boxes requiring high amperage - see below) One 50 amp GFCI Four #8 A WG copper wires Spas with the 6300 control box (when high amperage is selected on circuit board) SEE CONFIGURA TION INSTRUCTIONS ON NEXT P AGE. One 60 amp GFCI Four #8 A WG copper wires Ultim ...

  • Cal Spas A726L - page 12

    10 T esting the GFCI Breaker T est the GFCI breaker prior to rst use and periodically when the spa is powered. T o test the GFCI breaker follow these instructions (spa should be operating): Press the TEST button on the 1. GFCI. The GFCI will trip and the spa will shut off. Reset the GFCI breaker by 2. switching the breaker to the full OFF positi ...

  • Cal Spas A726L - page 13

    11 GFCI Wiring Diagram ...

  • Cal Spas A726L - page 14

    12 120 V olt Electrical Installation Always follow applicable local, state and federal codes and guidelines. Use only a dedicated electrical line with a 20-amp breaker . Cord-and-plug connections may not use a cord longer than 15 ft (4.6 m) and must be plugged into a dedicated 20-amp GFCI connection. Do not use extension cords! Always use a weather ...

  • Cal Spas A726L - page 15

    13 Electrical Installation -- Europe 230 V olt Electrical Installation All 230V spas must be permanently connected (hardwired) to the power supply . These instructions describe the only acceptable electrical wiring procedure. Spas wired in any other way will void your warranty and may result in serious injury . This is the only acceptable electrica ...

  • Cal Spas A726L - page 16

    14 Spa Model GFCI Required Wires Required Portable Spas All 230V spas (except 6205 control boxes requiring high amperage - see below) One 32 amp RCD or two 16 amp RCDs Four #10 A WG copper wires Spas with the 6300 control box (when high amperage is selected on circuit board) SEE CONFIGURA TION INSTRUCTIONS ON NEXT P AGE. One 32 amp RCD or two 16 am ...

  • Cal Spas A726L - page 17

    15 RCD Wiring Diagram ...

  • Cal Spas A726L - page 18

    16 Installing the In-Ground Shell ...

  • Cal Spas A726L - page 19

    17 Equipment Pack Plumbing Connections (In-Ground Spas) The example shown below is typical for a system with two pumps with external heater and external lter . Designer Spa Specications DIJ401 – DIJ406: Equipment pack weight = 250 lbs. DIJ407: Equipment pack weight = 300 lbs. 2.5 HP heat pump 4 HP swim pump Note: Equipment pack cannot excee ...

  • Cal Spas A726L - page 20

    18 ...

  • Cal Spas A726L - page 21

    19 Plumbing Connections IMPORT ANT! Always check local codes prior to any in-ground spa installation. Once the spa and equipment are properly located, you will want to lay out the plumbing run. T renches should be deep and wide enough to allow all pipes to be buried below the frost line and should be in as straight a line from the spa to the equipm ...

  • Cal Spas A726L - page 22

    20 NOTE: Once complete, water test the plumbing run for at least three days prior to covering any plumbing trenches and back-lling spa cavity completely . NOTE: Some local inspectors require pressure testing the plumbing lines. Although the spa is pressure tested at the factory , local inspectors may insist on pressure testing the plumbing run b ...

  • Cal Spas A726L - page 23

    21 Air V enturi: 1/2” line that is plumbed 18” above the spa’s water level. T opside Control Panel and T emp Sensor: 1” line that connects to the bottom of the control box located on the equipment pack. Electrical and Electronic Connection Remote Equipment T opside Control Panel The next few steps to complete the installation should be perf ...

  • Cal Spas A726L - page 24

    22 NOTE: Circuit board programming will not allow spa operation without both the temperature and high limit sensors being properly connected to the circuit board. Once topside panel operation is veried. T urn off power , disconnect 7. the extension loom from the circuit board and GENTL Y route through conduit to complete installation. NOTE: This ...

  • Cal Spas A726L - page 25

    23 Light niche and any metallic items in a 5’ (152 cm) radius must be properly bonded with #8 A WG grounding wire. Connect rigid conduit to the 3/4” hub located at the back of the light 1. niche and run to a water resistant junction box (or for 12 volt models to a low voltage transformer) no further than 25’ (7.6m). Remember this is a water c ...

  • Cal Spas A726L - page 26

    24 ...

  • Cal Spas A726L - page 27

    25 Pouring the Deck It is recommended that all electrical hook ups and all plumbing be completed before pouring the concrete. Make certain all electrical inspections on lights, bonding and all other electrical work have been completed and checked off by the local inspectors prior to proceeding with your concrete or nish work. It is a good idea t ...

  • Cal Spas A726L - page 28

    26 Spa T echnical Specications All sizes on this chart represent top-rail dimensions. Due to our continuous improvements, specications, size and pricing are subject to change without prior notice. A valon Series Model Width Length Depth Gallons Dry Weight Filled Weight A726B 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. A726L 84” 84” 39 1/ ...

  • Cal Spas A726L - page 29

    27 Classic and Legacy Series Model Width Length Depth Gallons Dry Weight Filled Weight CL-24 LL-24 64” 84” 32” 125 535 Lbs. 1576 Lbs. CP-34 LP-34 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. CT -34 L T -34 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. CA-34 LA-34 93” 93” 39 1/2” 450 900 Lbs. 4648 Lbs. CBA-34 LBA-34 93” 93” 39 1/2” ...

  • Cal Spas A726L - page 30

    28 Galaxy Series Model Width Length Depth Gallons Dry Weight Filled Weight GX-49 93” 93” 39 1/2” 450 900 Lbs. 4648 Lbs. Ultimate Fitness Series Model Width Length Depth Gallons Dry Weight Filled Weight FP 2400 96” 170” 52” 2000 1800 Lbs. 18460 Lbs. FP 2500 96” 206” 51” 2500 2000 Lbs. 22825 Lbs. FP 4700 96” 202” 52” 2000 / 28 ...

  • Cal Spas A726L - page 31

    29 ...

  • Cal Spas A726L - page 32

    L TR20081024, Rev . B 6/12/08 L.M.S. Customer Service Department 1462 East Ninth Street Pomona, CA 91766 T oll Free: 1-800-CAL-SP AS Fax: 1-909-629-3890 www .calspas.com ...

メーカー Cal Spas カテゴリー Hot Tub

Cal Spas A726Lのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- A726Lの取扱説明書
- Cal Spasの製品カード
- パンフレット
- またはCal Spas A726Lの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cal Spas A726Lの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cal Spas A726Lの取り付け説明書、サービスマニュアル、簡易説明書、またはCal Spas A726Lのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cal Spas A726Lの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cal Spas A726Lデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCal Spas A726Lを使用するのを助ける技術的文書のことです。説明書は通常、全てのCal Spas A726Lユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cal Spasの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cal Spas A726Lの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCal Spas A726Lの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cal Spas A726Lに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cal Spas A726Lデバイスの基本機能を使うにあたってのヒント。 Cal Spas A726Lのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cal Spas A726Lに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCal Spas A726Lのメーカー/サービスへの連絡先に関する情報。

Cal Spas A726Lについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCal Spas A726Lの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCal Spas A726Lで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)