-
Troy-Bilt 665B - page 1
Operator ’ s Manual Rear-tine T iller Model 664D—Pony ® 665B—ProLine ® E666M—Pony ® ES Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush - covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting appl ...
-
Troy-Bilt 665B - page 2
2 For more details about your unit, visit our website at www .troybilt.com T ABLE OF CONTENTS Content Page Calling Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Troy-Bilt 665B - page 3
Safety 1 Section 3 The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm. W AR NING This machine meets voluntary safety standard B71.8 – 1996, w hich is sponsored by the Outdoor Power Equipment Institute, Inc., and is published by the American National S ...
-
Troy-Bilt 665B - page 4
4 Section 1: Safety 7. Take all possible precautions when leaving the machine unattended. Stop the engine. Remove ignition key on electric start models. Disconnect spark plug wire and move it away from the spark plug. Move Wheel Gear Lever to ENGAGE. 8. Before cleaning, repairing, or inspect- ing, stop the engine, remove the ignition key on electri ...
-
Troy-Bilt 665B - page 5
Section 1: Safety 5 4. To reduce the chances of a fire hazard, keep the engine free of grass, leaves, or excessive grease. 5. Store gasoline in a cool, well-venti- lated area, safely away from any spark- or flame-producing equipment. Store gasoline in an approved container, safely away from the reach of children. 6. Refer to the Maintenance section ...
-
Troy-Bilt 665B - page 6
Assembly 2 Section 6 INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. INSPECT UNIT Inspect the unit and carton for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage ...
-
Troy-Bilt 665B - page 7
Section 2: Assembly 7 4. With the forward clutch cable (N, Figure 2-4) on the inside of handlebar, position the handlebar ends on the outside of the two mounting tabs (M, Figure 2-3) on the transmission top cover. NOTE: The curved handlebar height adjustment bracket appears as shown in C, Figure 2-3 for non-electric start units. For electric start ...
-
Troy-Bilt 665B - page 8
4. Check for correct spring/cable tension as instructed in Section 5, Checking and Adjusting Forward Clutch Belt Tension . 5. When tension is correct, tighten the two jam nuts (B) securely. STEP 5: CHECK TRANSMISSION GEAR OIL LEVEL The transmission was filled with gear oil at the factory. However, be sure to check the oil level at this time to make ...
-
Troy-Bilt 665B - page 9
Features and Controls 3 Section 9 Before operating your machine, care- fully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. WARNING INTRODUCTION This Section describ ...
-
Troy-Bilt 665B - page 10
10 Section 3: Features and Controls REVERSE CLUTCH CONTROL The Reverse Clutch Control (C, Figure 3-1) controls the engagement of reverse drive to the wheels and tines. The revers- ing feature is used for maneuvering the tiller only – never engage the tines in the ground while going in the reverse direction. To Operate the Reverse Clutch Control: ...
-
Troy-Bilt 665B - page 11
Operation 4 Section 11 Figure 4-1: Location of main tiller controls. INTRODUCTION Read this Section of the manual thor- oughly before you start the engine. Then, take the time to familiarize yourself with the basic operation of the tiller before using it in the garden. Find an open, level area and practice using the tiller controls without the tine ...
-
Troy-Bilt 665B - page 12
12 Section 4: Operation ST ARTING THE ENGINE The following steps describe how to start and stop the engine. Do not attempt to engage the tines or wheels until you have read all of the operating instruc- tions in this Section. Also review the safety rules in Section 1: “Safety” and the tiller and engine controls information in Section 3: “Feat ...
-
Troy-Bilt 665B - page 13
Section 4: Operation 13 (b) As the tiller moves forward, relax and let the wheels pull the unit along while the tines dig. Walk behind and a little to one side of the tiller. Use a light but secure grip with one hand on the handlebars, but keep your arm loose. See Figure 4-2. Let the tiller move ahead at its own pace and do not push down on the han ...
-
Troy-Bilt 665B - page 14
14 Section 4: Operation T illing Tips & T echniques Let the tiller do the work • While tilling, relax and let the wheels pull the tiller along while the tines do the digging. Walk on the side that is not yet finished (to avoid making foot- prints in the freshly tilled soil) and lightly, but securely grip the handlebar with just one hand. • ...
-
Troy-Bilt 665B - page 15
Section 4: Operation 15 T illing Tips & T echniques Clearing the tines The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may become tangled. Follow these proce- dures to help avoid tangling and to clean the tines, if necessary. • To reduc ...
-
Troy-Bilt 665B - page 16
16 Section 4: Operation POWER COMPOSTING Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutrients to the soil. The first place to begin is with crop re ...
-
Troy-Bilt 665B - page 17
Maintenance 5 Section 17 TILLER LUBRICA TION Proper lubrication of the tiller is an essen- tial part of your maintenance program. After every 10 operating hours, oil or grease the lubrication points shown in Figure 5-1 as described below. Use a good quality lubricating oil (#30 weight engine oil is suitable) and a good quality general purpose greas ...
-
Troy-Bilt 665B - page 18
18 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 19
Section 5: Maintenance 19 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 20
20 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 21
Section 5: Maintenance 21 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 22
22 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 23
Section 5: Maintenance 23 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 24
24 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 25
Section 5: Maintenance 25 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 26
26 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 27
Section 5: Maintenance 27 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped. Failure to follow these instructions can result in serious personal injury or pr ...
-
Troy-Bilt 665B - page 28
TROY -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the original purchaser only. WHAT IS COVERED Troy-Bilt LLC will, at its option, repair ...
Troy-Bilt 665Bについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもTroy-Bilt 665Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTroy-Bilt 665Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。