Liebert XDAの取扱説明書

16ページ 0.93 mb
ダウンロード

ページに移動 of 16

Summary
  • Liebert XDA - page 1

    Precision Cooling For Bu siness-Critical Con tinuit y Lieber t XDA ™ Air Flow Enhan c er User Manua l ...

  • Liebert XDA - page 2

    ...

  • Liebert XDA - page 3

    i TABLE OF CONTENTS 1.0 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 Equipment Inspection . . . . . . . . . . . . . . . . . . ...

  • Liebert XDA - page 4

    ii ...

  • Liebert XDA - page 5

    1 1.0 P RODUCT D ESCRIPTION The Liebert XDA Air Flow E nhancer increases the airflow through densely populated enclosures, breaki ng up hot spots within the enclo- sure that can threaten the uptime of your critical systems. Equipment fans often prod uce insufficient f low to push air through the masses of data communication wiring at the re ar of t ...

  • Liebert XDA - page 6

    2 2.0 I NST ALLATION The Liebert XDA can be attached to most equi pment cabinet doors 60" tall or taller. The unit typical ly is installed on the outside of a cabi- net’s rear door, generally used to discharge heat generated from the cabinet. If aisle space is insufficien t for exterior mounting, and space is avail- able inside the cabinet, ...

  • Liebert XDA - page 7

    3 2.2.1 Required T ools • Phillips screwdriver • Pliers • Scissors 2.3 Mounting the XDA on the Exterior of the Rear Cabinet Door 2.3.1 P rep are to Ins t all the Un it 1. Determine the desired mount- ing position on the door. 2. Attach the mounting bracket to the top of the XDA, positioning the bracket to obtain the desired mounting height. 3 ...

  • Liebert XDA - page 8

    4 2.3.2 Mount the Unit and Att ach it to the Cabinet 1. Lift the unit with bracket attach ed and h ang it on the door, as shown at right. Ensure that the bracket rests safely on top of the top edge of door. 2. Move the unit sideways into the desired position. Ensu re that the unit does not interfere with operation of the door latch. 3. Place screws ...

  • Liebert XDA - page 9

    5 2.4 Mounting the XDA on the Interior of the Rear Cabinet Door 2.4.1 P rep are to Ins t all the Un it 1. Remove the s crews on the sides of the XDA that secure the mounting angles to the unit. 2. Remove the mounting angles. 3. Position the angles so their mounting surfaces are near the fron t of the XDA . (This is the air discharge side, which has ...

  • Liebert XDA - page 10

    6 2.4.2 Mount the Unit and Att ach It to the Cabinet 1. Lift the unit onto the door, plac ing the two mounting holes on the top end, over the two screws atta ched to the door and bracket. Place nuts on the screws to hold the unit in place. 2. On the middle a nd lower mounting holes, place screws through the door and then thro ugh the mounting angle ...

  • Liebert XDA - page 11

    7 3.0 P OWER C ONNECTIONS Connect the power cords to separate power sources (as specified in Specifications on page 9 ), to keep the XDA operating if there is a power failure on one circuit. Route the power cords under or over the cabinet as needed to the ne arest av ailable receptacles. If only one power source is a vailabl e, connect both power c ...

  • Liebert XDA - page 12

    8 4.0 O PERATION & M AINTENANCE The XDA is activated by turning on the ON/OFF switch on the bottom of the unit, near the power cords. All fans operate continuously to remove the maximum amount of heat from the cab- inet. If a power failure sh ould occur on the primary power source, the XDA will operate from the secondary source until the primar ...

  • Liebert XDA - page 13

    9 5.0 S PECIFICATIONS Nominal Capacity 1000 CFM @ 60Hz Dimensions W x D x H, in (mm) 8 x 2.25 x 56 (203.2 x 57.2 x 1422.4) Wei ght, lbs (kg) 25 (1 1.3) Electrical S pecifications 120V -1-50/60Hz 230V -1-50/60Hz Amp Draw 1.5 A @ 120V 0.8 A @ 230V ...

  • Liebert XDA - page 14

    10 ...

  • Liebert XDA - page 15

    ...

  • Liebert XDA - page 16

    Ensuring The High A v ailab ilit y 0f Mission-Critic al Dat a And Applic a tions. While every precaution has been tak en to ensure the accuracy and complete ness of this literature , Liebert Corporation assumes no responsibility and disclaims all liability for damages resulting from u se of this informa tion or for any errors or omissions . © 2006 ...

メーカー Liebert カテゴリー Air Cleaner

Liebert XDAのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- XDAの取扱説明書
- Liebertの製品カード
- パンフレット
- またはLiebert XDAの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Liebert XDAの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Liebert XDAの取り付け説明書、サービスマニュアル、簡易説明書、またはLiebert XDAのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Liebert XDAの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Liebert XDAデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLiebert XDAを使用するのを助ける技術的文書のことです。説明書は通常、全てのLiebert XDAユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Liebertの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Liebert XDAの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLiebert XDAの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Liebert XDAに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Liebert XDAデバイスの基本機能を使うにあたってのヒント。 Liebert XDAのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Liebert XDAに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLiebert XDAのメーカー/サービスへの連絡先に関する情報。

Liebert XDAについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもLiebert XDAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLiebert XDAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)