Sioux Tools 5000APの取扱説明書

20ページ 0.29 mb
ダウンロード

ページに移動 of 20

Summary
  • Sioux Tools 5000AP - page 1

    Page No 1 Safety rules when using 5000A/5000AL/5000AP Imp act Wrenches – Use only impact sockets and extensions, universal joint s, etc. rated as being suitable for use with impact wrenches. – Prolonged exposure to vibration may cause injury . – Read all instructions before using this tool. All operators must be fully trained in its use and a ...

  • Sioux Tools 5000AP - page 2

    Page No 2 – T ake care against entanglement of the moving parts of the tool with clothing, hair , ties, cleaning rags, rings, jewelry , watches, bracelets, etc. This could cause the body or part s of the body to be drawn towards and in contact with the moving parts of the tool and could be very dangerous. – It is expected that users will adopt ...

  • Sioux Tools 5000AP - page 3

    Page No 3 Printed in T aiwan Dismantling & Assembly Instructions Disconnect tool from air supply . Unscrew hammer case cap screws (38) and take of f hammer case (36). T ake out hammer case pilot (35) and anvil (39, 39B or 39C) from hammer case (36). Release hammer (34) by removing hammer pin (33), then take off hammer frame rear washer (19) and ...

  • Sioux Tools 5000AP - page 4

    Page No 4 Règles de sécurité pour l’emploi des clés à chocs 5000A/5000AL/5000AP • Employez seulement des douilles, rallonges, cardans, etc. pour clé à choc qui réspondent aux conditions nominales de fonctionnement de la clé à chocs. • Une exposition prolongée aux vibrations peut causer des blessures. • Lisez les instructions avan ...

  • Sioux Tools 5000AP - page 5

    Page No 5 St ations de travail Cet outil est destiné à un usage manuel seulement. On recommande d’employer l’outil en position debout et sur un sol ferme. On peut l’employer dans d’autres positions mais avant un tel usage, l’opérateur doit se trouver dans une position stable, avoir l’outil bien en main, et être conscient que l’out ...

  • Sioux Tools 5000AP - page 6

    Page No 6 Impremé au T aiwan Instructions de démontage et de mont age Déconnectez l’outil de l’arrivée d’air . Dévissez les vis de fixation du carter de marteau (38) et retirez le carter de marteau (36). Retirez le pilote de carter de marteau (35) et l’enclume (39, 39B ou 39C) du carter de marteau (36). Libérer le marteau (34) en enle ...

  • Sioux Tools 5000AP - page 7

    Page No 7 Vibrationspegel: 13 m/Sek. Testverfahren: Getestet nach der ISO-Norm 8662 Teile 1 & 7 Lärmpegel: Lärmdruckpegel 97,0 dB (A) Lärmleistungspegel 108,0 dB (A) Testverfahren: Getestet nach dem Pneurop- Testcode PN8NTC1 und der ISO-Norm Nr. 3744 Verwendung einer Ausgleichs – bzw. Stützvorrichtung empfohlen: NEIN Nettogewicht des Prod ...

  • Sioux Tools 5000AP - page 8

    Page No 8 V orgesehener Einsatzbereich des Werkzeugs – 5000A/5000AL/5000AP Der Schlagschrauber ist zum Festziehen und Lösen von V erbindungselementen mit Gewinden innerhalb des vom Hersteller genannten Einsatzbereichs gedacht. Er darf nur mit geeigneten12,7 mm Innenvierkantaufsätzen für Einschlagmuttern verwendet werden. Es dürfen nur für Dr ...

  • Sioux Tools 5000AP - page 9

    Page No 9 Gedruckt in T aiwan Anleitungen zum Auseinander- und Zusammenbau Das Werkzeug von der Luftzufuhr abtrennen. Die Kopfschrauben (38) des Hammergehäuses abschrauben, und das Hammergehäuse (36) abnehmen. Den Führungsring (35) und den Amboss (39, 39B oder 39C) des Hammergehäuses vom Hammergehäuse (36) abnehmen. Den Hammer (34) durch Entfe ...

  • Sioux Tools 5000AP - page 10

    Page No 10 Nivel de vibración: 13 metros/seg 2 Método de prueba: Prueba efectuada de acuerdo con las normas ISO 8662, partes 1 & 7 Nivel de ruido: Nivel de presión de sonido 97,0 dB (A) Nivel de potencia de sonido 108,0 dB (A) Método de prueba: Prueba efectuada de acuerdo con el código de pruebas Pneurop PN8NTC1 y la norma ISO 3744. Uso re ...

  • Sioux Tools 5000AP - page 11

    Page No 11 Uso anticip ado de la herramient a – 5000A/5000AL/5000AP La llave de impacto ha sido diseñada para apretar y aflojar los fijadores de rosca dentro de la gama especificada por el fabricante. La herramienta se debe usar solamente con casquillos hembra apropiados de 12,7 mm, de tipo de impacto, para enroscar tuercas. Sólo use casquillos ...

  • Sioux Tools 5000AP - page 12

    Page No 12 Impreso en T aiwan Instrucciones para mont ar y desmont ar la herramient a Desconecte la herramienta del suministro de aire. Destornille los tornillos de cabeza (38) de la caja del martillo y saque la caja del martillo (36) hacia fuera. Retire el piloto de la caja del martillo (35) y el yunque (39, 39B y 39C) fuera de la caja del martill ...

  • Sioux Tools 5000AP - page 13

    Page No 13 Trillingsnivo: 13 m/s Test methode: getest in overeenstemming met ISO 8662, gedeelte 1 & 7 Geluidsnivo: Geluidsdruk niveau 97,0 dB (A) Geluidskracht niveau 108,0 dB (A) Test methode: Getest in overeenstemming met de Pneurop test code PN8NTC1 en ISO standaard 3744. Aanbevolen gebruik van balanceerder of onder- steuning NEE Product net ...

  • Sioux Tools 5000AP - page 14

    Page No 14 T e verwachten gebruik van het gereedschap – 5000A/5000AL/5000AP De slagmoersleutel is alleen ontworpen voor het aandraaien en losdraaien van met schroefdraad voorziene bevestigingsmiddelen, binnen het door de fabrikant gespecificeerde bereik. Het mag alleen gebruikt worden met het geschikte type 1/2" (12,7mm) vierkante slagdoppen ...

  • Sioux Tools 5000AP - page 15

    Page No 15 Gedrukt in T aiwan Demont age en Mont age Instructies Maak het gereedschap los van de luchttoevoer . Schroef de moerbouten (38) van de hamerbehuizing los en haal de hamerbehuizing (36) eraf. Haal de geleiding (35) en het aambeeld (39, 39B of 39C) uit de hamerbehuizing (36). Maak de hamer (34) los door de hamerpen (33) te verwijderen. V e ...

  • Sioux Tools 5000AP - page 16

    Page No 16 Livello di vibrazioni 13 m/sec 2 Metodo di collaudo: Collaudato secondo gli standard ISO 8662, parti 1 e 7 Rumorosità: Pressione acustica 97,0 dB (A) Potenza acustica 108,0 dB (A) Metodo di collaudo: Collaudato secondo la normativa di collaudo Pneurop PN8NTC1 e Standard ISO 3744. Si raccomanda l’uso di bilanciatore o supporto NO Peso ...

  • Sioux Tools 5000AP - page 17

    Page No 17 Post azioni di lavoro L ’utensile deve essere usato solo come strumento a mano. Si raccomanda di usare l’utensile stando in piedi su un piano solido. Può essere usato in altre posizioni, ma prima di tale uso, l’operatore deve porsi in posizione sicura, con una presa ed un appoggio solidi ed essere consapevole che, mentre si allent ...

  • Sioux Tools 5000AP - page 18

    Page No 18 S tampato in T aiwan Istruzioni per mont aggio e smont aggio Scollegare l’utensile dal sistema di alimentazione dell’aria. Svitare le viti (38) sulla calotta dell’alloggiamento del meccanismo di percussione (36). Estrarre la guida (35) dell’alloggiamento del meccanismo di percussione e l’incudine (39, 39B e 39C) dall’alloggia ...

  • Sioux Tools 5000AP - page 19

    Page No 19 5000A 1/2" Pistol Grip T win Hammer Impact W rench 5000AL Model 5000A with 2" Extended Anvil 5000AP Model 5000A with Pin Anvil Ref. No. Part No. Description Ref. No. Description Part No. 25 505822A Cylinder Dowel 26 505823A Hammer Case Bushing 27 505824A Rotor Blade (6 pc. set) 28 505825A Front End Plate 29 505826A Rear End Pla ...

  • Sioux Tools 5000AP - page 20

    Page No 20 ...

メーカー Sioux Tools カテゴリー Impact Driver

Sioux Tools 5000APのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 5000APの取扱説明書
- Sioux Toolsの製品カード
- パンフレット
- またはSioux Tools 5000APの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Sioux Tools 5000APの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Sioux Tools 5000APの取り付け説明書、サービスマニュアル、簡易説明書、またはSioux Tools 5000APのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Sioux Tools 5000APの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Sioux Tools 5000APデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSioux Tools 5000APを使用するのを助ける技術的文書のことです。説明書は通常、全てのSioux Tools 5000APユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Sioux Toolsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Sioux Tools 5000APの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSioux Tools 5000APの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Sioux Tools 5000APに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Sioux Tools 5000APデバイスの基本機能を使うにあたってのヒント。 Sioux Tools 5000APのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Sioux Tools 5000APに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSioux Tools 5000APのメーカー/サービスへの連絡先に関する情報。

Sioux Tools 5000APについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSioux Tools 5000APの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSioux Tools 5000APで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)