Extron electronic CS 120Pの取扱説明書

33ページ 6.42 mb
ダウンロード

ページに移動 of 33

Summary
  • Extron electronic CS 120P - page 1

    User Guide CS 26T and CS 120P Speakers CS 1226T SpeedMount Ceiling Speaker System 6 8-2161-01 Rev . A 08 13 ...

  • Extron electronic CS 120P - page 2

    Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock. A TTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and ...

  • Extron electronic CS 120P - page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interference when the equipment is operated in a commer cial environment. This equipment generates, uses, and can radiate radi ...

  • Extron electronic CS 120P - page 4

    Conventions Used in this Guide Notifications The following notifications are used in this guide: W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . A TTENTION: Attention indicates a situation that may damage or destroy the pr oduct or associated equipment. NOTE: A note draws attention to important ...

  • Extron electronic CS 120P - page 5

    Contents Introduction ............................................................ 1 About this Guide ................................................. 1 Overview ............................................................ 1 Features ............................................................. 1 Application Example ............................... ...

  • Extron electronic CS 120P - page 6

    CS 26T and CS 120P User Guide • Contents vi ...

  • Extron electronic CS 120P - page 7

    Intr oduction This section gives an overview of the Extron CS 1226T SpeedMount Ceiling Speaker System, consisting of the CS 26T speakers and CS 120P enclosure. It also pr ovides a list of system features and an application diagram. T opics include: • About this Guide • Overview • Features • Application Example About this Guide T ...

  • Extron electronic CS 120P - page 8

    • Selectable taps — The rotary tap selector switch, located behind the grille, sets the speaker to operate in either 8-ohm direct or 70 volt /100 volt operation with 16, 8, 4, 2, and 1 watt taps. • Magnetic grille — Magnets spaced around the grille edge enable it to be easily attached and to remain firmly in place. Application Example ...

  • Extron electronic CS 120P - page 9

    Installation This section provides instructions for installing the CS 26T speakers and the CS 120P enclosure. T opics include: • Installation Considerations • Installation Configurations • Installing the CS 1226T — Single Installer • Installing the CS 120P in a Suspended Ceiling — Division of Labor • Installing the CS 2 ...

  • Extron electronic CS 120P - page 10

    Installing the CS 1226T System — Single Installer If a single installer is installing the CS 1226T system, follow this procedur e for the entire system: NOTE: The ceiling grid must be installed before the installation of the CS 1226T begins. • V erify if fiberglass ceiling tiles ar e being used (see step 2 below and step11 on page 7 for ...

  • Extron electronic CS 120P - page 11

    e. Cut out the circle traced in the ceiling tile. f. Replace the tile in the ceiling. 4. R emove the adjacent ceiling tile — T o facilitate the installation process, r emove the tile adjacent to the ceiling tile where the CS 26T will be installed. If the CS 120P is being installed, skip to step 6. Otherwise, proceed to step 5. 5. If NOT using the ...

  • Extron electronic CS 120P - page 12

    8. Route the cables through the cover plate — NOTES: • The CS 120P is fully UL 2043 compliant only when it is used with a metal conduit or with plenum rated cables. • Installation of all conduits, conduit adapters, wiring, and electrical connections must conform to all applicable building codes and local ordinances. Using a flexible conduit: ...

  • Extron electronic CS 120P - page 13

    9. Wire the CS 120P — Route the wir es through the H-shaped opening in the CS 120P . Be sure to leave suf ficient slack. Figure 8. Route the Wires Thr ough the H-shaped Opening 10. Replace the terminal cover plate — Reinstall the terminal cover plate onto the CS 120P and tighten the two screws that wer e previously loosened. 11. If the CS 120P ...

  • Extron electronic CS 120P - page 14

    12. Place the CS 120P into the ceiling grid — Place the CS 120P over the tile grid so that the CS 120P is safely supported on the two short edges. Ensure that the hole in the tile is aligned with the hole in the CS 120P (see figure 10). Fig: Mounting the PRE NOTE: 2' x 2' (600 mm x 600 mm) grid mounting is the same as 2' x 4' ...

  • Extron electronic CS 120P - page 15

    16. Attach the speaker wires to the captive screw connector — A TTENTION: Do not tin the wires. Tinned wires do not r emain tight in the captive screws and can br eak easily after several bends. Number of Wires per Connection Point Maximum Wire Gauge 1 12 AWG 2 16 AWG 4 18 AWG Attach the speaker wires to the included four -pole captive screw conn ...

  • Extron electronic CS 120P - page 16

    • Wiring Multiple Speakers Using Loop-through: A loop-through electrical connection is made on the cr ossover board of the CS 26T . Connect the wires to the captive scr ew connectors of the speakers, as shown in figure 15. Be sur e to tighten the screws. Speaker 1 Speaker 2 Wiring Multiple Speakers Using Loop-through IN – LOOP – IN + LOOP ...

  • Extron electronic CS 120P - page 17

    • The impedance of the speakers downstream of the one being tested can be measured while the system is on by connecting to the outer (LOOP) terminals of the captive screw connector , as shown in figure 17. Impedance T est Points To next speaker(s) Red Wire (+) fr om Amplifier Black Wire (-) fr om Amplifier Amplifier Te st Points Figure 17. ...

  • Extron electronic CS 120P - page 18

    18. Attach the speaker wire to the strain relief tie down point using the pr ovided zip tie. Captive Sc re w Connector Strain Relief Ta b (zip tie) Figure 19. Attaching the Speaker Wir e to the Strain Relief Point 19. Mount the CS 26T (see figure 20). a. Insert the CS 26T through the bottom of the hole in the ceiling tile that was cut in step 3. b. ...

  • Extron electronic CS 120P - page 19

    20. Attach secondary support lines — If requir ed, attach all of the secondary support lines as shown in figure 21. A TTENTION: Do not allow any slack in the support cables. NOTE: If the CS 26T will be installed in the CS 120P , do not attach secondary support cables to the speakers. Secondary Support Cables (3) Attach cables he re and secure. An ...

  • Extron electronic CS 120P - page 20

    22. Set the rotary tap selector switch — Use a small screwdriver to set the tap selector switch to the appropriate setting. A TTENTION: When setting the taps for a distributed (high impedance) system, do not tap the system above the rated power of the amplifier . When connecting multiple speakers in 8-ohm mode, be sure that the combined rated im ...

  • Extron electronic CS 120P - page 21

    Installing the CS 120P in a Suspended Ceiling — Division of Labor In a division of labor installation, low-voltage contractors install the CS 120P enclosure (construction rough-in phase). NOTE: The ceiling grid must be installed before the installation of the CS 1226T can begin. • V erify if fiberglass ceiling tiles ar e being used (see ste ...

  • Extron electronic CS 120P - page 22

    4. Cut a hole for the CS 26T speaker . Use the provided cutout template to outline the hole to be cut in the ceiling tile as described below . (If the ceiling tile will not be installed during this phase of the installation, skip to step 6 .) a. Remove the ceiling tile. b. T o find the center of the tile, use a tape measure to measure the space bet ...

  • Extron electronic CS 120P - page 23

    7. Route the cables through the cover plate — NOTES: • The CS 120P is fully UL 2043 compliant only when it is used with a metal conduit or with plenum rated cables. • Installation of all conduits, conduit adapters, wiring, and electrical connections must conform to all applicable building codes and local ordinances. Using a flexible conduit: ...

  • Extron electronic CS 120P - page 24

    8. Wire the CS 120P — Route the wires through the H-shaped opening in the CS 120P . Be sure to leave suf ficient slack. Figure 29. Route the Wir es Through the H-shaped Opening 9. Replace the terminal cover plate — Reinstall the terminal cover plate onto the CS 120P and tighten the two screws that wer e previously loosened. 10. If the CS 120P i ...

  • Extron electronic CS 120P - page 25

    11. Place the CS 120P into the ceiling grid — Place the CS 120P over the tile grid so that the CS 120P is safely supported on the two short edges. If the ceiling tile was installed, ensure that the hole in the tile is aligned with the hole in the CS 120P (see figure 31). Fig: Mounting the PRE NOTE: 2' x 2' (600 mm x 600 mm) grid mountin ...

  • Extron electronic CS 120P - page 26

    Installing the CS 26T in a Suspended Ceiling — Division of Labor In a division of labor installation, an A V system contractor installs the CS 26T (final installation phase). Use the following procedur e: NOTE: Observe all applicable building codes and local ordinances when installing the speaker . 1. Disconnect power — Power down all attached ...

  • Extron electronic CS 120P - page 27

    5. Attach the speaker wires to the captive screw connector — A TTENTION: Do not tin the wires. Tinned wires do not r emain tight in the captive screws and can br eak easily after several bends. Number of Wires per Connection Point Maximum Wire Gauge 1 12 AWG 2 16 AWG 4 18 AWG Attach the speaker wires to the included four -pole captive screw conne ...

  • Extron electronic CS 120P - page 28

    • Wiring Multiple Speakers Using Loop-through: A loop-through electrical connection is made on the cr ossover board of the CS 26T . Connect the wires to the captive scr ew connectors of the speakers, as shown in figure 36. Be sur e to tighten the screws. Speaker 1 Speaker 2 Wiring Multiple Speakers Using Loop-through IN – LOOP – IN + LOOP ...

  • Extron electronic CS 120P - page 29

    • The impedance of the speakers downstream of the one being tested can be measured while the system is on by connecting to the outer (LOOP) terminals of the captive screw connector , as shown in figure 38. Impedance T est Points To next speaker(s) Red Wire (+) fr om Amplifier Black Wire (-) fr om Amplifier Amplifier Te st Points Figure 38. ...

  • Extron electronic CS 120P - page 30

    7. Attach the speaker wire to the strain relief tie down point using the pr ovided zip tie. Captive Sc re w Connector Strain Relief Ta b (zip tie) Figure 40. Attaching the Speaker Wir e to the Strain Relief Point 8. Mount the CS 26T (see figure 41). a. Insert the CS 26T through the bottom of the hole in the ceiling tile that was cut in step 2. b. T ...

  • Extron electronic CS 120P - page 31

    9. Set the rotary tap selector switch — Use a small screwdriver to set the tap selector switch to the appropriate setting. A TTENTION: When setting the taps for a distributed (high impedance) system, do not tap the system above the rated power of the amplifier . When connecting multiple speakers in 8-ohm mode, be sure that the combined rated imp ...

  • Extron electronic CS 120P - page 32

    Installing the CS 120P in a Har d Ceiling If you are installing the CS 1226T in a har d ceiling (having no ceiling tiles), with the ceiling structure in place, install the CS 120P: • It is the responsibility of the installer to identify a suitable mounting location and pr ovide the mounting hardwar e. • The CS 120P must be mounted as clos ...

  • Extron electronic CS 120P - page 33

    © 2013 Extron Electr onics All rights reserved. www .extron.com Contact Information Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron ...

メーカー Extron electronic カテゴリー Speaker

Extron electronic CS 120Pのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CS 120Pの取扱説明書
- Extron electronicの製品カード
- パンフレット
- またはExtron electronic CS 120Pの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Extron electronic CS 120Pの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Extron electronic CS 120Pの取り付け説明書、サービスマニュアル、簡易説明書、またはExtron electronic CS 120Pのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Extron electronic CS 120Pの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Extron electronic CS 120Pデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがExtron electronic CS 120Pを使用するのを助ける技術的文書のことです。説明書は通常、全てのExtron electronic CS 120Pユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Extron electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Extron electronic CS 120Pの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははExtron electronic CS 120Pの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Extron electronic CS 120Pに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Extron electronic CS 120Pデバイスの基本機能を使うにあたってのヒント。 Extron electronic CS 120Pのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Extron electronic CS 120Pに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるExtron electronic CS 120Pのメーカー/サービスへの連絡先に関する情報。

Extron electronic CS 120Pについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもExtron electronic CS 120Pの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがExtron electronic CS 120Pで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)