Linksys FENSK05 v2の取扱説明書

39ページ 0.65 mb
ダウンロード

ページに移動 of 39

Summary
  • Linksys FENSK05 v2 - page 1

    EtherFast ® Series 10/100 Network In a Bo x Model No.: FENSK05 v2 User Guide ...

  • Linksys FENSK05 v2 - page 2

    COPYRIGHT & TRADEMARKS Copyright © 2000 Linksys, All Rights Reserved. EtherFast is a register ed trademark of Linksys. Microsoft, Windows, and the Windows logo ar e registered trademarks of Microsoft Corporation. All other trademarks and brand names ar e the property of their respective pr oprietors. LIMITED W ARRANTY Linksys guarantees that e ...

  • Linksys FENSK05 v2 - page 3

    Linksys EtherFast ® Series 10/100 Network In a Box Introduction The Linksys EtherFast 10/100 Network In a Box The Linksys 10/100 Netw ork In a Box comes with e verything you need to get a net- w ork up and running in minutes. Plug in the cards, attach the provided netw ork cab les, install the software dri vers, and go! Built to run with the f ast ...

  • Linksys FENSK05 v2 - page 4

    10/100 Network In a Box Getting to Know the EtherFast 10/100 Network In a Box The EtherFast 10/100 LAN Card Y ou will install one EtherF ast 10/100 LAN Card into each computer you wish to netw ork. The Card’ s LEDs Link/Act The Link LED will illuminate when the card has been suc- cessfull y connected to a netw ork and flicker when data is being t ...

  • Linksys FENSK05 v2 - page 5

    The Hub’ s Ports 1-5 P orts 1-5 are where you will connect y our PCs to the hub . It is through these ports that network information is exchanged. Uplink Y ou can expand y our netw ork by connecting y our hub to another hub, switch, router or Broadband modem through the Uplink port. If the Uplink por t is being used , the port adjacent to it will ...

  • Linksys FENSK05 v2 - page 6

    10/100 Network In a Box 5. Once y our EtherF ast EtherF ast 10/100 LAN Card is f irmly in place , secure its fastening tab to your PC's chassis with a mounting scre w . 6. Replace y our PC's co ver . 7. Connect one end of a twisted-pair cable to y our PC at the EtherF ast 10/100 LAN Card's RJ-45 por t. 8. Plug the other end of the ca ...

  • Linksys FENSK05 v2 - page 7

    10/100 Network In a Box 9 Windows 98 Installation & Setup Overview After ph ysically installing the EtherF ast 10/100 LAN Card in your computer , follo w these instructions to install the network dri ver . The installation proce- dure for the netw ork dri ver will v ar y slightly depending on w hich version of W indo ws 98 you are using, and on ...

  • Linksys FENSK05 v2 - page 8

    10/100 Network In a Box Linksys EtherFast ® Series 4. Select "Search for the best dri ver for your de vice (Recommended). ” Click Next. 5. Select "Flopp y disk driv es". Click Next to continue. 6. A windo w will open saying that W indo ws is no w ready to install the Linksys LNE100TX F ast Ethernet Adapter driver (seen on the ne x ...

  • Linksys FENSK05 v2 - page 9

    10/100 Network In a Box 13 Linksys EtherFast ® Series 12 Network Component Configuration 1. Once you are back at the W indo ws 98 desktop, click on your taskbar's Start button, then Settings , then Control P anel , and then double-click the Netw ork icon. 2. The Netw ork window will appear . Click on the Conf iguration tab . A windo w similar ...

  • Linksys FENSK05 v2 - page 10

    10/100 Network In a Box 15 Linksys EtherFast ® Series 14 8. Click on the Identif ication tab . T ype the name of y our computer in the Computer Name box. Choose a name that is unique from the other com- puter names on the netw ork. 9. T ype the name of your w orkgr oup in the W or kgr oup box. The W orkgroup name should be the same W orkg roup Nam ...

  • Linksys FENSK05 v2 - page 11

    10/100 Network In a Box 17 Linksys EtherFast ® Series 16 14. A Logon windo w will appear , requiring you to enter a User name and P assw ord . Make up a user name and pass w ord (if you ha ven’ t already) and click OK . Do not click the Cancel button or Escape ke y . Clicking either of these buttons will prev ent you from lo gging into the netwo ...

  • Linksys FENSK05 v2 - page 12

    10/100 Network In a Box 19 Linksys EtherFast ® Series 18 Installing the Driver in Windows 95 V ersion B 1. While the Update Device Driver W izar d windo w is visible (pre vious page), put the EtherF ast Card 10/100 LAN Card Dri ver Disk into your flopp y driv e and click Next . 2. W indo ws 95 will f ind the Linksys LNE100TX F ast Ethernet Adapter ...

  • Linksys FENSK05 v2 - page 13

    10/100 Network In a Box 21 Linksys EtherFast ® Series 20 Network Component Configuration 1. Once you are back at the Windo ws 95 desktop, click on your taskbar's Start button, then Settings , then Control P anel , and then double-click the Netw ork icon. 2. The Netw ork window will appear . Click on the Conf iguration tab . A windo w similar ...

  • Linksys FENSK05 v2 - page 14

    10/100 Network In a Box 23 Linksys EtherFast ® Series 22 8. Click on the Identif ication tab . T ype the name of y our computer in the Computer Name box. Choose a name that is unique from the other com- puter names on the netw ork. 9. T ype the name of your w orkgroup in the W or kgroup bo x. The W orkgroup name should be the same W orkgroup Name ...

  • Linksys FENSK05 v2 - page 15

    10/100 Network In a Box 25 Linksys EtherFast ® Series 11. Optional : Choose the Access Contr ol tab . Ensure that Shar ed-level access contr ol is selected. If the setting is on User-Lev el access control and you can’ t change it, skip to problem 5 in the Troub leshooting section on page 45. 12. Click the OK button. Y our system may or ma y not ...

  • Linksys FENSK05 v2 - page 16

    10/100 Network In a Box 27 Linksys EtherFast ® Series 26 3. The Install Hardwar e Device Drivers dialog bo x will appear . Whe n Ethernet Contr oller is displa yed , select “Searc h for a suita ble driver f or your device (Recommended)” . Click Ne xt . 4. The Locate Driver F iles dialog bo x will appear . Select “Specify a loca- tion” . Cl ...

  • Linksys FENSK05 v2 - page 17

    10/100 Network In a Box 7. The Completing the F ound New Hardwar e Wizard dialog bo x will appear .The follo wing adapter name will be sho wn: Linksys LNE100TX F ast Ethernet Adapter (LNE100TX v4). Click Finish . 8. Remo v e the driv er disk from the floppy dri ve. The Windo ws 2000 driver installation is complete. If you w ant to share f iles or p ...

  • Linksys FENSK05 v2 - page 18

    10/100 Network In a Box 31 Linksys EtherFast ® Series 30 3. Click on the Select fr om list... button to select a netw ork adapter . 4. Click on the Ha ve Disk button. Inser t the EtherF ast 10/100 LAN Card Driver Disk into driv e A. T ype a: into the box on y our screen and hit OK . 5. Highlight the Linksys LNE100TX F ast Ethernet Adapter (LNE100 ...

  • Linksys FENSK05 v2 - page 19

    10/100 Network In a Box 33 Linksys EtherFast ® Series 32 8. A list of services will appear . Click Next to appro ve these services, fol- lo w ed by Ne xt again. 9. NT will probabl y ask you to suppl y your original W indo ws NT CD-R OM or setup disks. If so, place your Windo ws NT CD-R OM in your CD dri ve. If the CD-R OM loads a pop-up window , c ...

  • Linksys FENSK05 v2 - page 20

    10/100 Network In a Box 35 Linksys EtherFast ® Series 34 13. Click Finish . When asked if you w ant to restar t your computer , remov e the Driv er Disk and click Ye s . 14. Once your PC has rebooted and y ou are logged in, doub le-click the Netw ork Neighborhood icon on y our desktop. Ensure that you ha ve access to the netw ork. If you do, y our ...

  • Linksys FENSK05 v2 - page 21

    10/100 Network In a Box 37 Linksys EtherFast ® Series 36 3. When the list of a vailab le netw ork adapters appears, click the Ha ve Disk button. 4. Put the EtherF ast Card disk into driv e A. T ype a: into the box on your screen and click OK . 5. Highlight the Linksys LNE100TX F ast Ethernet Adapter (LNE100TX v4) entry in the window that appears. ...

  • Linksys FENSK05 v2 - page 22

    10/100 Network In a Box 10. Remo ve your Dri ver Disk and CD-R OM and click Ye s to restar t your PC. 11. Once your PC has rebooted , double-click the Netw ork Neighborhood icon on your desktop. Ensure that y ou ha ve access to the netw ork. If you do, your card has been properl y installed. • If you had pr eviously installed an y NT service pack ...

  • Linksys FENSK05 v2 - page 23

    10/100 Network In a Box 41 Linksys EtherFast ® Series 40 5. If the LAN dri ver is not located in the default director y , specify the f ile's path on the command line. The LO AD command prompts you for the con- f iguration parameters if they are not supplied on the command line. 6. At the ser ver command line, type (for example): LOAD c:LNE1 ...

  • Linksys FENSK05 v2 - page 24

    10/100 Network In a Box 13. Ar row do wn the list that appears and choose which protocols y ou want to install. Press F10 to sa ve. 14. Highlight Sa ve P arameters and Load Driv er . Press Enter . 15. Y our PC will examine the netw ork. This may tak e a few minutes. 16. Y ou ma y be prompted sev eral times for a netw ork on which to bind IPX to LNE ...

  • Linksys FENSK05 v2 - page 25

    10/100 Network In a Box 45 Linksys EtherFast ® Series 44 5. On the Access Control T ab, User Level Access is selected, but Shared Level Access is grayed out and not accessible . • Y ou previousl y had your primary network lo gon set to Client for NetW ar e Networ ks . On the Conf iguration tab of the Networ k Pr operties windo w , ensure that yo ...

  • Linksys FENSK05 v2 - page 26

    10/100 Network In a Box 47 Linksys EtherFast ® Series 46 • Click on the IRQ Steering tab . Remo ve the check from Use IRQ Holder and click OK . W indo ws will ask you to restart the PC (if it doesn’ t ask you, then reboot the PC manuall y). • After the computer boots up, W indo ws will tr y to re-detect the PCI Steering. Continue rebooting t ...

  • Linksys FENSK05 v2 - page 27

    10/100 Network In a Box 49 Appendix Sharing Y our Files and Printers Overview By sharing your f iles and printers, other PCs on your netw ork will be able to access the resources on your PC. Before sharing your f iles and printers, you should prepare y our computer to be used with an y f ile ser vers that ma y be on the netw ork. If you are not usi ...

  • Linksys FENSK05 v2 - page 28

    10/100 Network In a Box 51 Linksys EtherFast ® Series 50 Installing the Driver in Windows 95 V ersion A 1. W indo ws 95 will detect the EtherF ast card and display a Ne w Har dwar e F ound windo w . 2. Slide the EtherF ast Card Driv er Disk into drive A. 3. Select Driver fr om disk pro vided by har dwar e manufactur er , then click OK . 4. When as ...

  • Linksys FENSK05 v2 - page 29

    10/100 Network In a Box 53 Linksys EtherFast ® Series 52 Windows 98 or 95 Client for Windows NT If you are installing the EtherF ast 10/100 Card in a W indo ws 95 or 98 PC that you plan on lo gging into a NT domain ser ver , follo w the directions belo w . 1. F ollow the W indo ws 95 setup instr uctions or the W indo ws 98 setup instructions 2. St ...

  • Linksys FENSK05 v2 - page 30

    10/100 Network In a Box 55 Linksys EtherFast ® Series 54 4. Remov e any instance of the name Linksys in the bo x. This includes IPX/SPX…Linksys , NetBEUI…Linksys , and TCP/IP…Linksys . Also remo v e Client for Micr osoft Networ ks , Client for NetW ar e Networ ks , and F ile and Printer Sharing for Micr osoft Networks . In some cases, remo v ...

  • Linksys FENSK05 v2 - page 31

    10/100 Network In a Box 57 Linksys EtherFast ® Series 56 Starting Over in Windows 2000 1. Click the Star t button, choose Settings, choose Control Panel, then dou- ble-click the System icon.The System Properties windo w will open. 2. Choose the Hardware tab . 3. Click the Device Manager button. The Device Manager windo w will open. 4. Click the pl ...

  • Linksys FENSK05 v2 - page 32

    10/100 Network In a Box 59 Linksys EtherFast ® Series 58 Manually Installing the Network Components in Windows 95 & 98 There ma y be times when y ou might need to manually install missing W indo ws netw orking components. 1. Click on Start , Settings , then Control P anel . 2. Double-click the Netw ork icon. The Network windo w appears. 3. Cli ...

  • Linksys FENSK05 v2 - page 33

    10/100 Network In a Box 61 Linksys EtherFast ® Series 60 N N o o t t e e : : Some PME-sup- porting motherboards may not requir e the WOL wire to be con- nected. Check your PC’ s documentation for more information. Installing and Configuring W ake-On-LAN Overview Only install the W ake-On-LAN wires if your motherboard supports remote wak e-up ev ...

  • Linksys FENSK05 v2 - page 34

    10/100 Network In a Box 63 Linksys EtherFast ® Series 62 Sending a Magic Packet In order to use W OL you need to kno w the MA C address of the card you wish to “wak e”. If you don’ t kno w the MA C address of the PC you are on, turn to page 48 to lear n how to run the EtherF ast Card’ s diagnostic program. 1. T ur n off the PC on w hich yo ...

  • Linksys FENSK05 v2 - page 35

    10/100 Network In a Box 65 Linksys EtherFast ® Series 64 No Changes Allowed Y our PC may not allo w you to change the IRQ v alue(s) of the PCI slot(s). In this case, you will ONL Y be able to use the IRQ and I/O v alues that hav e been pre-assigned to each slot. The popular BIOS from Phoenix, for example, does not generall y allo w you to modify B ...

  • Linksys FENSK05 v2 - page 36

    10/100 Network In a Box 67 Linksys EtherFast ® Series 66 • • S S t t r r a a i i g g h h t t - - T T h h r r o o u u g g h h C C a a b b l l i i n n g g • • C C r r o o s s s s - - O O v v e e r r C C a a b b l l i i n n g g Crimping Y our Own Network Cables T wisted-Pair Cabling There are dif ferent g rades, or categories, of twisted-pair ...

  • Linksys FENSK05 v2 - page 37

    10/100 Network In a Box 69 Linksys EtherFast ® Series 68 10/100 LAN Card Specifications Model Numbers: LNE100TX v4 System: PCI 2.1 (or higher) compliant PC Standards: IEEE 802.3, IEEE 802.3u, PCI 2.1 & 2.2, A CPI, PC99 Protocol: CSMA/CD P orts: One Combo RJ-45 10BaseT/100BaseTX Speed: Full Duplex 200Mbps/20Mbps Half Duplex 100Mbps/10Mbps Cabli ...

  • Linksys FENSK05 v2 - page 38

    10/100 Network In a Box 71 Linksys EtherFast ® Series 70 Customer Support F or help with the installation or operation of your EtherF ast 10/100 Netw ork in a Box, contact Linksys Customer Support at one of the phone numbers or Internet addresses below . Customer Support (800) 326-7114 (949) 261-1288 Information (800) 546-5797 Fa x (949) 261-8868 ...

  • Linksys FENSK05 v2 - page 39

    © Cop yr ight 2000 Linksys, All Rights Reserved. http://www .linksys.com ...

メーカー Linksys カテゴリー Network Card

Linksys FENSK05 v2のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- FENSK05 v2の取扱説明書
- Linksysの製品カード
- パンフレット
- またはLinksys FENSK05 v2の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Linksys FENSK05 v2の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Linksys FENSK05 v2の取り付け説明書、サービスマニュアル、簡易説明書、またはLinksys FENSK05 v2のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Linksys FENSK05 v2の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Linksys FENSK05 v2デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLinksys FENSK05 v2を使用するのを助ける技術的文書のことです。説明書は通常、全てのLinksys FENSK05 v2ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Linksysの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Linksys FENSK05 v2の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLinksys FENSK05 v2の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Linksys FENSK05 v2に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Linksys FENSK05 v2デバイスの基本機能を使うにあたってのヒント。 Linksys FENSK05 v2のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Linksys FENSK05 v2に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLinksys FENSK05 v2のメーカー/サービスへの連絡先に関する情報。

Linksys FENSK05 v2についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもLinksys FENSK05 v2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLinksys FENSK05 v2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)