Paxar 9465の取扱説明書

12ページ 0.47 mb
ダウンロード

ページに移動 of 12

Summary
  • Paxar 9465 - page 1

    Monarch®, Pathfinder® Ultra®, 6039, 9462, a nd 9465 are trademarks of Paxar Americas, Inc. Paxar® is a trademark of Paxar Corporation. Avery Dennison® is a trademark of Avery Dennison Corporation. TC6039QR Rev. AE 1/08 ©2005 Pa xar Americas, Inc. a subsidia ry of Avery Dennison Corp. All Rights Reserved. QUICK REFERENCE This Quick Re ference ...

  • Paxar 9465 - page 2

    2 Attaching the Safety Strap 1. Turn the printer upside down, resting its top in the table. 2. Remove the stylus strap from the loop. 3. Take the thin end of the safety strap, and push it through the loop at the bottom of the printer han dle (near the battery comp artment). 4. Push the thick en d of the safe ty strap through the thin end ’s loop. ...

  • Paxar 9465 - page 3

    3 Changing the Main B attery Always take the main ba ttery out of the printer when s toring the printer and connect the Battery Backup Power. 1. Turn the printer over and press the button on the battery comp artment door (at the botto m of the pr inter’s handle) and slide it o pen. 2. Turn the printer upright, holding your palm beneath the open b ...

  • Paxar 9465 - page 4

    4 Note: If the printer does not ha ve a main battery or is not connected to the Bat tery Backup Power , it loses its charge and the printer’s s ystem settings. 5. Remove the main battery from the battery compartment. 6. Connect the Battery Backup Power as shown. Loading Supplies 1. Turn on the printer. 2. Press the latch buttons and op en the sup ...

  • Paxar 9465 - page 5

    5 6. Place a roll of sup ply in the supply holder so it unrolls fr om the bottom . 7. Load the supplies for the pr inting mode you want: Pe el or Non-Peel. Loading for Non-Peel Mode 1. Feed the supply under the ap plicator roller a nd over the label defl ector. 2. Close the supply cover. 3. Select Load S upply from the printer icon menu, choose you ...

  • Paxar 9465 - page 6

    6 3. Feed all four inches of the backing pap er over the peel bar and u nder the applicator roller a nd the labe l deflector . 4. Push the label deflector up until it snaps into p lace. 5. Partially close the co ver to the first position . 6. Pull the backing paper over the guide roller, down to the pinch and feed rollers. 7. Hold the backing paper ...

  • Paxar 9465 - page 7

    7 Changing the Display Settings To change the backlight, sound (bee p) and other s tandard Windows options , from the Start Menu select Settings , Control Panel . Using the Keypad The printer ’s keypad appears below . Key(s) Descript ion Enter Accepts data or a me nu selection. Tab Tabs to the next tab stop or the next fie ld. Pressing Fct + Tab ...

  • Paxar 9465 - page 8

    8 Entering Data Entering data using the keypad is simila r to en tering data on a cell ph one. There are three data entry modes: ♦ Normal (Numeric) mode – Default . Press the key to displa y what appears on the fa ce of the key (numb ers). ♦ Lower-Case Alpha betic mode – Press Alpha once to display lower-case letters. Press th e key several ...

  • Paxar 9465 - page 9

    9 Black Mark Sensor On- Demand Sensor Platen Roller Cleaning th e Pinch and Feed Rollers 1. Turn off the printer and ope n the supply cover. 2. Remove the supplies. 3. Turn the pla ten roller with your fingers and run a dry, lin t-free cloth across the pinch and fee d rollers as the y turn. Make sure the rollers are clean all the way around. If tha ...

  • Paxar 9465 - page 10

    10 Scanner Flex Cable Adhesiv e Buildup 4. Use a dry, soft-bri stle brus h, such as a toothbr ush, to clean the pl aten roll er. 5. Turn the platen roller with your finger and then continue cle aning. 6. Reload the supplies, close the labe l deflector and supply cover . If the brush does not remove all the adhesive, mo isten a cotton swab with isop ...

  • Paxar 9465 - page 11

    11 Troubleshooting This section l ists some common problems and their solutions. Problem Solution Printer does not print. Switch to a fully-charged ba ttery. Load the supply correctly. Clean the printhead. Printer does not feed. Switch to a fully-charged ba ttery. Close the supply cover completely. Load the supply correctly. Check the platen roller ...

  • Paxar 9465 - page 12

    12 Error Codes Following are some common error codes you may receive. See your System Administrator if you receive any codes not listed here. Code(s) Description 004 – 005 Supply size is incorrect. Reload the correct supplies. 267 – 271 410 – 413 Communication error. See y our System Administrator. 703 – 704 Load supplies or make sure they ...

メーカー Paxar カテゴリー Printer

Paxar 9465のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9465の取扱説明書
- Paxarの製品カード
- パンフレット
- またはPaxar 9465の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Paxar 9465の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Paxar 9465の取り付け説明書、サービスマニュアル、簡易説明書、またはPaxar 9465のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Paxar 9465の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Paxar 9465デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPaxar 9465を使用するのを助ける技術的文書のことです。説明書は通常、全てのPaxar 9465ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Paxarの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Paxar 9465の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPaxar 9465の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Paxar 9465に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Paxar 9465デバイスの基本機能を使うにあたってのヒント。 Paxar 9465のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Paxar 9465に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPaxar 9465のメーカー/サービスへの連絡先に関する情報。

Paxar 9465についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPaxar 9465の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPaxar 9465で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)