Graco 310649Cの取扱説明書

22ページ 1.1 mb
ダウンロード

ページに移動 of 22

Summary
  • Graco 310649C - page 1

    Instr uctions - P ar ts A utomatic Plural Component, Imping ement Mix Spra y Gun For use with non-flammab le foam and pol yurea. Not f o r use in e x plosive atmospheres. 3500 psi (24.2 MP a, 242 bar) Maxim um Fluid Working Pressure 80-130 psi (0.55-0.9 MP a, 5.5-9. 1 bar) Air Inlet Pressur e Range 200 ° F (94 ° C) Maximum Fl uid T emperature Air ...

  • Graco 310649C - page 2

    Contents 2 310649C Contents Manual Con v entions . . . . . . . . . . . . . . . . . . . . . . . . 2 Air Purge Guns . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Round Pattern Gu ns . . . . . . . . . . . . . . . . . . . . . . 3 Flat P atte rn Guns . . . . . . . . . . . . . . . . . . . . . . . . 3 Related Manuals . . . . . . . . . . . . . ...

  • Graco 310649C - page 3

    Air Purge Guns 310649C 3 Air Pur g e Guns Round P attern Guns Flat P attern Guns Related Manuals F or complete saf ety , operat ion, and repair inf or mat ion, ref er to the applicab le man ual listed below . Mix Chamber Gun P ar t No., Series P ar t No. Impingement Po r t S i z e in (mm) Equivalent Size 248376, A AR2929 .029 (0.70) -00 248377, A A ...

  • Graco 310649C - page 4

    Mechanical Purge Guns 4 310649C Mec h anical Pur g e Guns Standar d Round P attern Guns Direct Impingement Round P attern Guns Direct Impingement Flat P attern Guns Related Manuals F or complete safety , operation, a nd repair informatio n, refer to the applicable manual listed be low . Use only these mix module/tip comb inations. Gun P ar t No., S ...

  • Graco 310649C - page 5

    Warning 310649C 5 W ARNING SKIN INJECTION HAZ ARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce ski n. This may look lik e just a cut, but it is a serious injur y that can resu lt in amputation. Get immediate surgical treatmen t. • Do not point th e gun at any one or at any par t of the body . • Do not put your ha ...

  • Graco 310649C - page 6

    Isocyanate Hazard Kee p A and B Components Sep arate 6 310649C Isoc y anate Hazar d K eep A and B Components Separate BURN HAZARD Equipment surf aces and fluid that’ s heated can become v er y hot during operation. T o av oid se vere burns, do not to uch hot fluid or equipm ent. W ait until equipm ent/fluid has c ooled comp letely . T O XIC FLUID ...

  • Graco 310649C - page 7

    Grounding 310649C 7 Gr ounding Chec k your local electrical code and pr opor tioner man- ual f or detailed grounding instructions. Ground the sp ray gun through connection to a Graco-appro ved grounded fluid supply hose. Piston Safe ty Loc k Engage piston sa fety lock whene ver y ou stop spray- ing, to av oid accidental triggering. T urning Air Cap ...

  • Graco 310649C - page 8

    Overall Vi ew 8 310649C Overall Vie w Key: A A Side Fluid V a lve (ISO) B B Side Fluid V a lve (RESIN) CA i r C a p D Fluid Housing E Gun Fluid Manifold F Cleanoff Air V alve G Piston Safety Loc k H CeramTip (behind air cap) J Optional Fluid Inlets (A Side Shown) K Lock Ring L Fluid Inlet Swivels (A Side Sho wn) M Optional Air Inlets (A Side Shown) ...

  • Graco 310649C - page 9

    Installation 310649C 9 Installation Mounting gun to r od Mounting gun to stationary suppor t or robot arm 1. T o mount the gun o n a 1/2 in. diameter rod, inser t the bar (A) thr ough the hole in the gun body as shown. 2. Secure the gun to the bar b y tightening 1/4 in. - 2 0 mounting scre ws. T o mount gun to stationary suppor t or robot arm, see ...

  • Graco 310649C - page 10

    Installation 10 310649C Connecting airline and accessories 1. On each gun air su pply line, install an air pressu re regulator . • It is recommende d that the tip clean off air , gun actuation, and gun deactuation air be supplied and regulated separ ately . • A minimum of 80 psi (. 55 mpa, 5.5 bar) air pres- sure must be supp lied to the gun fo ...

  • Graco 310649C - page 11

    Setup 310649C 11 Setup 1. Close fluid v alves A and B . 2. Connect A (ISO) and B (RESIN) fluid hose s to fluid manif old. 3. Engage pist on safety loc k . 4. Connect the airlines, see In stallation page 8. Attach fluid man ifold (D) to gun. T o change position of fluid manif old or use optional flui d inlets, see Fusion Gun man ual 309856 or 30955 ...

  • Graco 310649C - page 12

    Setup 12 310649C 7. Actuate gun to chec k fo r full mix chamber trav el. F ront of air cap (C) sh ould be approximat ely flush with front retainin g r ing (U). 8. Open cleanoff air valv e (K) 1/4-1/2 tur n and actuate air line to check that clean off air is flowing. Adjust as desired. 9. Engage pist on safety loc k . 10. T ur n on proportioner . TI ...

  • Graco 310649C - page 13

    Pressure Relief Procedure 310649C 13 Pressure Relief Pr ocedure Read wa r nings, page 5. Relie ve pressure bef ore cleaning or repairing gun. 1. Engage pist on safety loc k . CA UTION Air supply is required f or gun actuation. Do not dis- connect gun air suppl y until fluid pressure is relie ved. 2. Close fluid v alves A and B. Lea ve air inlet (W) ...

  • Graco 310649C - page 14

    Shutdown 14 310649C Shutdo wn F or complete shutdown proce dure, ref er to Fusion Gun manual 309550 or 309856. ...

  • Graco 310649C - page 15

    Shutdown 310649C 15 ...

  • Graco 310649C - page 16

    Parts 16 310649C Pa r t s Air Pur g e Gun 24 15 ‡ 8 7 ‡ 27 ‡ 19 1 ‡ 25 ‡ 9 ‡ 10 23 ‡ * ‡ 11 3 ‡ ‡ 26e ‡ 26c ‡ 26d 12c 12f 12e 12b 12d TI4521b 50 ‡ 37 TI2557A Flat Pattern Detail Round Pattern Gun Shown 19 10 39 40 † * 3 T orque to 235-24 5 in-lb (26.6-27.7 N•m). T orque to 35-45 in-lb (4-5 N•m). T orque t o 32-40 ft- ...

  • Graco 310649C - page 17

    Parts 310649C 17 * These par ts are only av a ilable in repair kits. T o select a kit, ref er manual 3095 50. † These par ts are not av ailable singly . ‡ These par ts are included in F ront End Replacemen t Kit 246361.  These par ts are included in Safety St op Assembly 248064 (include s 1 of item 24).  Replacement Danger and W ar ning l ...

  • Graco 310649C - page 18

    Parts 18 310649C Mechanical Pur ge Gun TI4523b 92 8 46* †‡ 25 39 19 32 16* 8 31 14*  15  10  17  59  3  18  1 35 ‡ 11 ‡ 23 ‡ 46* †‡ 21* ‡ 20 ‡ 44 ‡ *24 †‡ 7 † 12a 12b 12d 12g 50 12c 12e 12f 34 40 T orque to 125-135 in-lb (14-15 N•m). T orque to 32-40 ft-lb (43-54 N•m). 1 3 3 1 1 1 TI3870a 54 53 Sup ...

  • Graco 310649C - page 19

    Parts 310649C 19 * These par ts are only av a ilable in repair kits. T o select a kit, ref er to Gun Repair Kits in man ual 309856. † These par ts are not av ailable singly . ‡ These par ts are included in Fluid Housing Asse mbly Kit 248004 (i ncludes 1 of items 24 and 46).  These par ts are included in Safety St op Assembly 248028 (include ...

  • Graco 310649C - page 20

    Mounting Dimensions 20 310649C Mounting Dimensions Gun mounting plate dimensions in. (mm) F IG . 1 ti4751b 1.30 (33.0) 0.625 (15.88) 0.625 (15.88) 1 (25.4) 3 x 1/8 npt 2 x 1/4-20 2 x ⌀ 0.127 (3.23) 1.06 (26.92) 0.73 (18.54) 4 x M5 ...

  • Graco 310649C - page 21

    Technical Data 310649C 21 T ec hnical Data All brand names or mar ks are used f or identification purposes and are trademarks of Gra co Inc. or their respectiv e own er s. Accessories Category Data Maximum Fluid W orking Pressure 3500 psi (24.2 MP a, 242 bar) Minimum Air Inle t Pressure 80 psi (0.55 MP a, 5.5 bar) Maximum Air Inlet Pre ssure 130 ps ...

  • Graco 310649C - page 22

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. This manual contains English. MM 310649 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea ...

メーカー Graco カテゴリー Paint Sprayer

Graco 310649Cのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 310649Cの取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco 310649Cの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco 310649Cの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco 310649Cの取り付け説明書、サービスマニュアル、簡易説明書、またはGraco 310649Cのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco 310649Cの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco 310649Cデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco 310649Cを使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco 310649Cユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco 310649Cの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco 310649Cの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco 310649Cに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco 310649Cデバイスの基本機能を使うにあたってのヒント。 Graco 310649Cのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco 310649Cに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco 310649Cのメーカー/サービスへの連絡先に関する情報。

Graco 310649Cについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco 310649Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco 310649Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)