-
Hans Grohe 38118XX1 - page 1
Installation Instructions / W arranty Uno 38117XX1 Uno 38118XX1 ...
-
Hans Grohe 38118XX1 - page 2
2 W all Mounted Single-Handle Lav Set with Base Plate 38117XX1 W all Mounted Single-Handle Lav Set 38118XX1 38117XX1 38118XX1 T echnical Data Max. flow rate: 2 .2 g p m Max. water pressure: 147 psi Recommended pressure: 14.7 - 72 psi T est pressure: 232 psi Max. hot water temperature: 176° F* Recommended hot water temp.: 120° F - 140° F* Require ...
-
Hans Grohe 38118XX1 - page 3
3 Installation with 38111181 rough manufactured before 03/2004 T urn the water off at the supply before beginning this installation. Remove the covers from the plaster shields (1). T rim the plaster shields so that they extend 1/16” out- side the surface of the finished wall (2). Seal the wall around the plaster shield with waterproof sealant. Us ...
-
Hans Grohe 38118XX1 - page 4
4 Install the new cup washers and springs in the rough. Install the cartridge assembly . Installation with 38111181 rough manufactured after 04/2004 Remove the covers from the plaster shields. T rim the plaster shields so that they extend 1/16” outside the surface of the finished wall. Seal the wall around the plaster shield with waterproof seala ...
-
Hans Grohe 38118XX1 - page 5
5 Install the cartridge and anti-twist device in the housing. Install the cup washers and springs in the rough. Install the cartridge assembly . Installation with all models: Push the handle over the cartridge stem. Tighten the handle screw with a 2 mm Allen wrench. If you are installing 38117XX1, turn to page 6. If you are installing 38118XX1, tur ...
-
Hans Grohe 38118XX1 - page 6
6 Model 38117XX1 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 7/8”, select the two “A” sleeves (1 1/4”). If x is between 3 7/8” - 4 3/8”, select the two “B” sleeves (7/8”). If x is greater than 4 3/8”, select the two “C” sleeves (1/2”). x A B C 1 1/4” 7 ...
-
Hans Grohe 38118XX1 - page 7
7 Connect the fixation nuts to the sleeves. Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1” to X. Cut the threaded end of the spout so that it is X + 1” long (2). Push the baseplate against the wall (1). Thread the sleeves into the rough (2). 1. 2. X + 1” 1. 2. ...
-
Hans Grohe 38118XX1 - page 8
8 Lightly lubricate the o-rings on the spout and handle escutcheons with the enclosed lubricant (1). Push the escutcheons onto the baseplate. W rap the threads on the spout with T eflon tape (1). Install the spout (2). Install the handle flange (3). T ighten the retaining nuts with the ser vice key . 1. 2. 3. 1. 2. ...
-
Hans Grohe 38118XX1 - page 9
9 Model 38118XX1 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 7/8”, select the “A” sleeve (1 1/4”). If x is between 3 7/8” - 4 3/8”, select the “B” sleeve (7/8”). If x is greater than 4 3/8”, select the “C” sleeve (1/2”). x A B C 1 1/4” 7/8” 1/2” ...
-
Hans Grohe 38118XX1 - page 10
10 Push the sleeve / handle escutcheon assembly into place over the handle (1). T ighten it by rotating it clockwise (2). Push the flange over the handle. Push the sealing ring into the handle escutcheon (1). Install the handle escutcheon onto the sleeve (2). 1. 2. 1. 2. ...
-
Hans Grohe 38118XX1 - page 11
11 Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1” to X. Cut the threaded end of the spout so that it is X + 1” long (2). Install the spout escutcheon on the spout. Push the sealing ring into the spout escutcheon. W rap the threads on the spout with T eflon tape (1). Install the spout (2). 1. 2. 1 ...
-
Hans Grohe 38118XX1 - page 12
12 38117XX1 User Instructions Pivot the handle up to turn the water on, down to turn it off. Pivot the handle to the left for warmer water , to the right for cooler water . on off 1 2 3 4 5 6 7 11 8 ...
-
Hans Grohe 38118XX1 - page 13
13 1 flange 96908XX0 2 handle 10092XX0 3 escutcheon for handle 96912XX0 4 escutcheon for spout 96913XX0 5 baseplate 96914XX0 6 cartridge cpl. 96339000 7 aerator cpl. 96911XX0 8 fixing set 97971000 9 escutcheon for spout 96910XX0 10 escutcheon for handle 96909XX0 11 extension set (not included) 38982000 XX = color 00 = chrome 82 = brushed nickel Rep ...
-
Hans Grohe 38118XX1 - page 14
14 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...
-
Hans Grohe 38118XX1 - page 15
15 including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS W ARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT P A Y FOR: A. Conditions, malfunctions or damage not resulting from defects in material or w ...
-
Hans Grohe 38118XX1 - page 16
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770 360-9880 • Fax 770 360 9887 www .hansgrohe-USA.com US - Installation Instructions • Part No. 90500703 • Revised 07/2007 ...
Hans Grohe 38118XX1についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHans Grohe 38118XX1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHans Grohe 38118XX1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。