-
Lumiscope sw-1000 - page 1
Transcutaneous Electrical Model SW-1000 Opera tion Manual Nerve Stimulation (TENS) Read this manual bef ore oper ating the TENS device Sa v e th is m an ua l f or fut ur e us e . T he m os t cu rr ent v e rs ion o f th is m an ua l c a n b e f ound online a t ww w . gr ah am fiel d. co m ...
-
Lumiscope sw-1000 - page 2
...
-
Lumiscope sw-1000 - page 3
TABLE OF CONTENTS INTRODUCTION TO TENS INDICA TIONS AND CONTRAINDICA TIONS WARNINGS PRECAUTIONS/ADVERSE REACTIONS ABOUT THIS DEVICE UNIT CONTROLS A TT ACHING THE LEAD WIRES ELECTRODE SELECTION AND CARE TIPS FOR SKIN CARE CONNECTING THE TENS DEVICE BA TTERY INFORMA TION CARING FOR YOUR TENS DEVICE TROUBLESHOOTING WARRANTY SYSTEM COMPONENTS TECHNICAL ...
-
Lumiscope sw-1000 - page 4
INTRODUCTION TO TENS What is Pain? Pain is the body’s warning system. Pain is important because it signals an unusual condition in the body and alerts us before additional damage or injury can occur . TENS was developed to help relieve some types of chronic and acute pain. How does TENS work? TENS is a method of treating pain that is non-inv asiv ...
-
Lumiscope sw-1000 - page 5
- - - - Contraindications Patients with implanted electronic devices ( for example, a pacemaker ) or metallic implants should not undergo TENS treatment without first consulting a physician. Any elec tro de pl acem ent that appl ies curr ent to the caro tid (nec k) re gion . Any electrode placement that causes current to flow tr anscerebrally (thro ...
-
Lumiscope sw-1000 - page 6
MODE (uS) P ULSE WI DTH (Hz) P ULSE RA TE Lead Connector Intensity Controls Indicator Light Pulse Width Control Mode Selector Pulse Rate Control Battery Compartment Battery Strip 03 60 100 180 230 250 1 60 115 150 10 PRECAUTIONS/ADVERSE REACTIONS Caution: Isolated cases of skin irritation may occur at the site of electrode placement during long ter ...
-
Lumiscope sw-1000 - page 7
ABOUT THIS DEVICE Y our TENS device is a battery operated device that includes two controllable output channels. This TENS device creates electrical impulses whose ampli- tude, duration, and modulation can be altered with the controls or switches. T h e TE NS in te ns it y c o n tr ol s ar e ve ry ea sy to us e, an d th e sl id e co ve r pr ot ec t ...
-
Lumiscope sw-1000 - page 8
Mode Functions Burst (B) releases individual bursts twice per second, pulse width is adjustable and the pulse rate is set at 100Hz per second. Continuous (C) stimulation is delivered continuously at the settings deter- mined by intensity , rate, and width knobs. Modulation (M) pulse width decreases the pulse width down to 60% of the original width ...
-
Lumiscope sw-1000 - page 9
TIPS FOR SKIN CARE Good skin care is important for effective and comfortable use of your TENS device. Always clean the electrode site with mild soap and water solution, rinse well and dry thoroughly prior to any electrode application. Any excess hair should be clipped, not shaved, to ensure good electrode contact with the skin. If a skin treatment ...
-
Lumiscope sw-1000 - page 10
3. Place electrodes on the skin Place the electrodes on the skin as recommended by your clinician. 4. Insert the Lead Wire Connector to the TENS device Plug the end of the lead wire into the lead connector port to be used, pushing plug in as far as it will go. 5. Select T reatment Settings Ensure the unit is set to the proper settings (Pulse Width, ...
-
Lumiscope sw-1000 - page 11
Changing the battery When the yellow indicator light on the front of the unit does not light up when the unit is turned on, the battery should be replaced. 1. Remove the panel cover by pressing o n the top and sliding down until it is completely removed from the unit. This will rev eal the battery compartment. 2. Remo ve the discharged battery from ...
-
Lumiscope sw-1000 - page 12
TROUBLESHOOTING If the TENS device does not function properly: 1. Make sure the battery is properly installed or replace the battery . Be sure to observe proper polarity markings when replacing the battery . If the yellow light on the front of the unit does not stay lit when the unit is turned on, replace the battery and check again. 2. If the ON/O ...
-
Lumiscope sw-1000 - page 13
TECHNICAL SPECIFICATIONS Dual, isolated between channels Burst, Continuous, Modulation Adjustable 0-80mA peak into 500 ohm load each channel, constant current 1Hz-150Hz (adjustable) 60uS-250uS (adjustable) Burst consists 2 burst per sec at 100 Hz Asymmetrical Bi-Phasic square pulse 0-100 V olt (open current) 9 volt battery 95(H) x 65(W) x 23.5 (T) ...
-
Lumiscope sw-1000 - page 14
...
-
Lumiscope sw-1000 - page 15
...
-
Lumiscope sw-1000 - page 16
USA, Corporate Headquarters: GF Health Products, Inc. 2935 Northeast Parkway Atlanta, Georgia 30360 fax: 800-726-0601, 678-291-3232 www .grahamfield.com SW-1000-INS-LAB-RevB09 GF Health Products, Inc., December 2009 telephone: 800-347-5678, 770-447-1609 ...
Lumiscope sw-1000についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもLumiscope sw-1000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLumiscope sw-1000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。