Patton electronic 2703の取扱説明書

11ページ 0.06 mb
ダウンロード

ページに移動 of 11

Summary
  • Patton electronic 2703 - page 1

    USER MANU AL MODEL 2703 G.703/E1 Digital Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2703-I Doc# 031041UI Revised 08/16/99 An ISO-9001 Certified Company ...

  • Patton electronic 2703 - page 2

    1.0 WARRANTY INFORMA TION Patton Electronics warrants all Model 2703 components to be free from defects, and will—at our option—repair or replace the prod- uct should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse, or unauthorize ...

  • Patton electronic 2703 - page 3

    2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warrant- ed for One Y ear parts and labor . If any questions or problems arise during installation or use of this product, please do not hesitate to con- tact Patton Electronics T echnical Support at ...

  • Patton electronic 2703 - page 4

    3.1.1 Switch Set S1 The configuration switches on S1 set clocking, rate adaptation, loopback enable, data invert, and interface (see also Switch S2). The default settings are summarized in table below . Switch S1-1: T erminal Interface (W orks in Conjunction with Switch S2) Set Switch S1-1 (as well as S2-1 and S2-2)to determine whether the signals ...

  • Patton electronic 2703 - page 5

    Switch S1-8: Loopback T est Enable Depending upon the setting of switch S1-8 the Model 2703 will either be continually in loopback mode, or loopback mode will be enabled by pressing and holding the front panel switch. Since the front panel switch is spring loaded–it returns to “Normal” operation when pressure is released–this DIP switch pro ...

  • Patton electronic 2703 - page 6

    The internal jumpers mounted on the Model 2703’s PC board (labeled LK1 - LK7) are used to configure the 75 ohm or 120 ohm net- work link parameters. Figure 4 (above) shows the location of the Model 2703’s jumpers on the internal PC board. The table below shows the factory default jumper settings. Following the table are descriptions for each ju ...

  • Patton electronic 2703 - page 7

    Jumper LK6 & LK7: 75 Ohm T ermination Impedance This jumper sets the termination impedance correctly for 75 Ohm operation. Both jumpers must be in place when operating in 75 Ohm (unbalanced) mode. Conversely , both jumpers must be removed when operating in 120 Ohm (balanced) mode. LK6 LK7 Setting On On 75 ohm operation Off Off 120 ohm operation ...

  • Patton electronic 2703 - page 8

    4.2 CONNECTION TO THE TERMINAL DEVICE The Model 2703 is wired as a DCE, and–when configured proper- ly–supports communication with a wide variety of terminal (DTE) devices. Compatible interface standards include EIA-530 (RS-422), CCITT X.21 and CCITT V .35. All interfaces are supported on a female UD-26 connector (a sub- miniature 26-pin “D? ...

  • Patton electronic 2703 - page 9

    5.3 LOOPBACK TEST (LAL) The Model 2703 is equipped with a Local Analog Loopback (LAL) mode to assist in evaluating the operation of the local Model 2703. Any data sent to the local Model 2703 in this test mode will be echoed (returned) back to the user device. For example, characters typed on the keyboard of a terminal will appear on the terminal s ...

  • Patton electronic 2703 - page 10

    APPENDIX B P A TTON MODEL 2703 PIN CONFIGURA TIONS 17 13- (CTS/) Clear to Send 12- (TC/) Transmit Clock 1 1- Not Used 10- (CD/) Carrier Detect 9- (RC/) Receive Clock 8- (CD) Carrier Detect 7- (SG) Signal Ground 6- (DSR) Data Set Ready 5- (CTS) Clear to Send 4- (RTS) Request to Send 3- (RD) Receive Data 2- (TD) Transmit Data 1- Shield UNIVERSAL D-26 ...

  • Patton electronic 2703 - page 11

    19 APPENDIX C (contd) P A TTON MODEL 2703 F ACTOR Y P ARTS AND ACCESSORIES C-3 T erminal (DTE) Interface Cables No terminal (DTE) cable is supplied with the Model 2703. Y ou may construct your own cable using the pin-out diagrams in Appendix B, or purchase one of the Patton’s standard adapter cables listed below . Custom lengths are available. ...

メーカー Patton electronic カテゴリー Network Router

Patton electronic 2703のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2703の取扱説明書
- Patton electronicの製品カード
- パンフレット
- またはPatton electronic 2703の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Patton electronic 2703の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Patton electronic 2703の取り付け説明書、サービスマニュアル、簡易説明書、またはPatton electronic 2703のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Patton electronic 2703の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Patton electronic 2703デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPatton electronic 2703を使用するのを助ける技術的文書のことです。説明書は通常、全てのPatton electronic 2703ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Patton electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Patton electronic 2703の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPatton electronic 2703の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Patton electronic 2703に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Patton electronic 2703デバイスの基本機能を使うにあたってのヒント。 Patton electronic 2703のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Patton electronic 2703に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPatton electronic 2703のメーカー/サービスへの連絡先に関する情報。

Patton electronic 2703についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPatton electronic 2703の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPatton electronic 2703で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)