GE JVB64の取扱説明書

12ページ 0.52 mb
ダウンロード

ページに移動 of 12

Summary
  • GE JVB64 - page 1

    Us e and Care & Installation G uide Downdraft Vent System Models: JVB34 JVB65 JVB35 JVB93 JVB64 JVB96 GE Appliances Safety Instructions .........................2 Operating Instructions, Tips Canning .............................................................3 Controls .............................................................3 Cooking Tip ...

  • GE JVB64 - page 2

    W ARNING—TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y TO PERSONS, OBSER VE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer . If you have questions, contact the manufacturer . B. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power f ...

  • GE JVB64 - page 3

    SER VICING NOTE: BE SURE ELECTRICAL POWER IS OFF BEFORE SER VICING THE UNIT . It may be necessary to remove the downdraft blower system from the cabinet in order to service components such as the blower motor or air vent mechanism. Disconnect power to the cooktop and remove it first. Reverse the steps in the Install the Downdraft section to remove ...

  • GE JVB64 - page 4

    Gr ease Filter The efficiency of your downdraft depends on a clean filter . Frequency of cleaning depends on the type of cooking you do. Grease filters should be cleaned at least once a month. Never operate the downdraft without the filters in place. T o r emove: Pull the filters out by grasping them and pulling straight up. T o clean: Soak and the ...

  • GE JVB64 - page 5

    5 INST ALLA TION INSTRUCTIONS Before Starting Installation Check the Following Requirements This downdraft blower system is designed to be used to exhaust smoke and odors when cooking with all GE electric and sealed bur ner gas cooktops (not approved for standar d bur ner gas cooktops). It can be mounted in either an island or peninsula location. R ...

  • GE JVB64 - page 6

    30 ″ COOKT OPS/DOWNDRAFT UNITS JVB34, JVB35, JVB93 Figure 2 Overall Cutout Dimensions Figure 3 Cutout for Vent Figure 1 Overall Cooktop Dimensions 1 2 3 NOTE: AGAINST -THE-W ALL INST ALLA TIONS ARE LIMITED DUE TO DIMENSION REQUIREMENTS. REFER TO DET AILS BELOW . PLANNING INSTALLATION (Note: 26 ″ deep cabinets required) PREPARING CUTOUT A B C B& ...

  • GE JVB64 - page 7

    7 36 ″ COOKT OPS/DOWNDRAFT UNITS JVB64, JVB65, JVB96 Figure 2 Overall Cutout Dimensions Figure 3 Cutout for Vent Figure 1 Overall Cooktop Dimensions 1 2 3 NOTE: AGAINST -THE-W ALL INST ALLA TIONS ARE LIMITED DUE TO DIMENSION REQUIREMENTS. REFER TO DET AILS BELOW . PLANNING INSTALLATION (Note: 26 ″ deep cabinets required) PREPARING CUTOUT A B C ...

  • GE JVB64 - page 8

    INST ALLA TION INSTRUCTIONS (continued) 8 Plan the Ductwork 1. This downdraft blower system is designed for use with 3 1 ⁄ 4 ″ x 10 ″ ductwork (can be transitioned to 6 ″ round). Three dif ferent discharge directions ar e available with side--to-side adjustment for accurate alignment of ductwork. 2. For best per for mance: Choose the ductin ...

  • GE JVB64 - page 9

    9 Plan the Wiring 1. The downdraft blower system draws 4 AMPS and requires a 120 V AC, 60 Hz cir cuit. 2. The unit has a 2 ft. long power cord with a 3-pronged plug. Plan to provide a gr ounded outlet in a location which will allow the unit’s power cord to r each. The outlet cannot be located on a back wall. The outlet needs to be mounted on the ...

  • GE JVB64 - page 10

    10 INST ALLA TION INSTRUCTIONS (continued) Install the Downdraft 1. Set the downdraft into the opening. Extend the leveling brackets to the floor of the cabinet so the downdraft sits straight. ( NOTE: Leveling brackets can be removed and r e-attached in other positions. The bottom flange may have to face inward in tight cabinet installations.) 2. S ...

  • GE JVB64 - page 11

    1 1 Adjust the Switch The downdraft is factor y-adjusted for pr oper operation. However , shipping and handling may af fect the positions of the activating switch. T o adjust position of activating switch: 1. If the downdraft is plugged into the electrical outlet, unplug it. 2. Lift the air vent straight up and cock it slightly so it remains in the ...

  • GE JVB64 - page 12

    WHA T IS COVERED FULL ONE-YEAR W ARRANTY For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any part of the downdraft system that fails because of a manufacturing defect. This warranty is extended to the original purchaser and any succeeding owner for products purc ...

メーカー GE カテゴリー Ventilation Hood

GE JVB64のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- JVB64の取扱説明書
- GEの製品カード
- パンフレット
- またはGE JVB64の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、GE JVB64の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、GE JVB64の取り付け説明書、サービスマニュアル、簡易説明書、またはGE JVB64のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、GE JVB64の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

GE JVB64デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGE JVB64を使用するのを助ける技術的文書のことです。説明書は通常、全てのGE JVB64ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

GEの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. GE JVB64の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGE JVB64の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。GE JVB64に関してこのドキュメントで見つけることができる全てのヒントの目次
3. GE JVB64デバイスの基本機能を使うにあたってのヒント。 GE JVB64のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。GE JVB64に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGE JVB64のメーカー/サービスへの連絡先に関する情報。

GE JVB64についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGE JVB64の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGE JVB64で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)