Delta 31-280の取扱説明書

16ページ 0.59 mb
ダウンロード

ページに移動 of 16

Summary
  • Delta 31-280 - page 1

    INSTRUCTION MANUAL Sanding Center 6" Belt/12" Disc Sander (Model 31-280) P ART NO. 406-12-651-0004 - 07-31-01) Copyright © 2001 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-35 ...

  • Delta 31-280 - page 2

    2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and proper operating pr ocedures ar e not followed. As with all machinery , there ar e cer- tain hazards involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety pr ecau ...

  • Delta 31-280 - page 3

    3 ADDITIONAL SAFETY RULES FOR SANDING CENTER 1. WARNING: Do not operate this tool until assembly and installation are complete, according to instructions. 2. WARNING: Unguar ded rotating shafts can cr eate an entanglement hazard. AL WA YS COVER THE POWER T AKE- OFF SHAFT when accessories are not in use. 3. IF YOU ARE NOT thoroughly familiar with th ...

  • Delta 31-280 - page 4

    4 4 Fig. 1 Fig. 2 GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER GROUNDING INSTRUCTIONS WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERA TOR FROM ELECTRIC SHOCK. 1. All grounded, cor d-connected tools: In the event of a malfunction or breakdown ...

  • Delta 31-280 - page 5

    2 5 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the tool. An undersized cor d will cause a ...

  • Delta 31-280 - page 6

    6 ASSEMBL Y INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED, AND YOU READ AND UNDERST AND THE ENTIRE OWNER'S MANUAL. Fig. 7 ASSEMBLING ST AND 1. Attach the four rubber feet (E) Fig. 7 to the bottom of each leg (C). 2. Attach the two lower braces (A) Fig. 7, a ...

  • Delta 31-280 - page 7

    7 Fig. 9 A TT ACHING SANDING DISC CAUTION: DISCONNECT TOOL FROM POWER SOURCE. 1. Clean the sanding disc plate (A) Fig. 9 of any oil or grease, and be certain that it is dry . 2. Peel approximately 1/2 of the backing (B) Fig. 9 fr om the sanding disc (C). 3. Insert the sanding disc (C) with the paper backing downward between the disc assembly and th ...

  • Delta 31-280 - page 8

    8 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING THE TOOL The on-off switch (A) Fig. 14 is located on the sander base. T o tur n the sander “ON”, move the switch to the up position. T o turn the sander “OFF”, move the switch to the down position. LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the tool is not in use, ...

  • Delta 31-280 - page 9

    9 Fig. 17 Fig. 16 IMPORT ANT : THE TOOL IS SHIPPED WITHOUT BEL T TENSION. BEFORE OPERA TING THE TOOL, ADJUST THE BEL T FOR CORRECT TENSION AND PROPER TRACKING BY DOING THE FOLLOWING: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Loosen the two lock knobs (A) Fig. 17, and remove the top cover (B). 3. T ur n the belt tension lever (C) Fig. 18 clockwise to ...

  • Delta 31-280 - page 10

    ADJUSTING BEL T SANDER T ABLE MITER GAUGE SLOT P ARALLEL TO SANDING BEL T 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Position the table (Figs. 25 and 26) 90 degrees to the belt. Place a squar e (B) in the miter gauge slot with the blade (C) of the square touching the sanding belt. Check the opposite end of the belt to see if the miter gauge slot (D) ...

  • Delta 31-280 - page 11

    11 Fig. 28 Fig. 27 Fig. 26 Fig. 25 CHANGING POSITION OF SANDING ARM 1. The sanding arm (A) can be used in the vertical position (Fig. 27), the horizontal position (Fig. 28), or any angle in between. Loosen the lock handle (B), position the arm (A) to the desired angle, and tighten the lock handle (B). 2. The top idler pulley cover (A) Fig. 28 can b ...

  • Delta 31-280 - page 12

    12 Fig. 31 Fig. 30 Fig. 32 TIL TING THE DISC SANDER T ABLE The table (A) can be tilted 45 degrees up (Fig. 31), or 45 degr ees down (Fig. 32), by loosening the lock handle (B), tilt- ing the table (A), and tightening lock handle (B). The degree of tilt is determined by the scale (C) Fig. 32, and pointer (D) Fig. 32. NOTE: When tilting the table dow ...

  • Delta 31-280 - page 13

    13 ADJUSTING SANDING DISC GUARD 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Adjust the sanding disc guard (A) Fig. 35, so that the fr ont edge of the guard is slightly in fr ont of the sanding disc for small work, and slightly behind the sanding disc for lar ge work. 3. T o adjust, move the guard (A) Fig. 35 in or out as r equired. The scr ews do not ...

  • Delta 31-280 - page 14

    POWER T AKE-OFF SHAFT 1. DISCONNECT TOOL FROM POWER SOURCE. 2. A power take-off shaft is pr ovided on the lower end of the sanding belt arm to accommodate accessories. 3. For access to the power take-off shaft, r emove the two screws (A) Fig. 43, and cover (B). 4. WARNING: Unguar ded rotating shafts (C) Fig 41 can create an entanglement hazar d. AL ...

  • Delta 31-280 - page 15

    15 15 ACCESSORIES A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . WARNING: Since accessories other than those offer ed by Delta ha ...

  • Delta 31-280 - page 16

    16 The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , PORT A-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SA W BOSS ® , SPEED-BLOC ® , SPEEDMA TI ...

メーカー Delta カテゴリー Cordless Sander

Delta 31-280のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 31-280の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta 31-280の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta 31-280の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta 31-280の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta 31-280のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta 31-280の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta 31-280デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta 31-280を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta 31-280ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta 31-280の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta 31-280の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta 31-280に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta 31-280デバイスの基本機能を使うにあたってのヒント。 Delta 31-280のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta 31-280に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta 31-280のメーカー/サービスへの連絡先に関する情報。

Delta 31-280についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta 31-280の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 31-280で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)