Kenwood KDC-4554Uの取扱説明書

23ページ 0.75 mb
ダウンロード

ページに移動 of 23

Summary
  • Kenwood KDC-4554U - page 1

    KDC-4554U KDC-4054UB KDC-4054UR KDC-3454UQ KDC-3354UGY KDC-3254URY KDC-3054UG KDC-3054UR KDC-3054URY KDC-316UR CD-RECEIVER INSTRUCTION MANUAL CD-RECEIVER BEDIENUNGSANLEITUNG РAДИОПРИЕMНИК С KOMПAKT –ДИСKAMИ ИHCTPУKЦИЯ ПO ЭKCПЛУA T AЦИИ АВТОМАГНІТОЛА ІНСТРУКЦІЯ З ЕКСПЛУ А Т АЦІЇ GET ...

  • Kenwood KDC-4554U - page 2

    2 Safety 3 Preparation 4 How to attach/detach the faceplate How to reset your unit Basic operations 5 Getting started 7 Canceling the display demonstration Setting the demonstration mode Adjusting the clock Initial settings before operations Listening to the radio 8 Adjust [SETTINGS] mode settings Listening to a disc/ USB device/ iPod 10 Start play ...

  • Kenwood KDC-4554U - page 3

    3 ENGLISH Safety WARNING Stop the car before operating the unit. Important to know... T o pr event a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Caution: Adjust the volume so that you can hear sounds outside the car . Driving with the volume too high may cause an accident. Condensation: Whe ...

  • Kenwood KDC-4554U - page 4

    4 Preparation How to attach/detach the faceplate 2 1 1 2 Do not expose the faceplate to direct sunlight, excessive heat, or humidity . Also avoid places with too much dust or the possibility of water splashing. Keep the faceplate in its casing while detached. The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. T o ...

  • Kenwood KDC-4554U - page 5

    5 ENGLISH The following indicator lights up when... ST : A stereo broadcast is r eceived (FM). IN : A disc is in the unit. TI : T raffic Information function is turned on. RDS : Radio Data System ser vice is available. For : EQ : [PRESET EQ] is set to an EQ mode other than [NATURAL] . (page 15) B.BOOST : [BASS BOOST] is set to [B.BOOST LV1] , [B.BO ...

  • Kenwood KDC-4554U - page 6

    6 When you press or hold the f ollowing button(s)... Button General operation SRC T urns on. T urns off if pressed and held. Selects the available sources ( TUNER, USB/ iPod, CD , AUX, ST ANDBY ), if the power is turned on. • If the source is ready, playback also starts. • “iPod” or “CD” is selectable only when an iPod is connected or a ...

  • Kenwood KDC-4554U - page 7

    7 ENGLISH Getting started Canceling the display demonstration The display demonstration is always turned on unless you cancel it. When you turn on the power (or after you reset the unit), the display shows: [CANCEL DEMO] [PRESS] [VOLUME KNOB] 1 Press the volume knob. [YES] is selected as the initial setup. 2 Press the volume knob again to confi ...

  • Kenwood KDC-4554U - page 8

    8 Listening to the radio 1 Press SRC to select “TUNER.” 2 Press repeatedly to select a band (FM1/ FM2/ FM3/ MW/ LW). 3 Press 4 / ¢ to search for a station. Item Selectable setting (Preset: *) PRESET TYPE NORMAL/ NORM *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ MW/ LW). ; MIX: Memorizes one station for each pres ...

  • Kenwood KDC-4554U - page 9

    9 ENGLISH Adjust [SETTINGS] mode settings While listening to the radio... 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [SETTINGS] , then press to enter. 3 Turn the volume knob to make a selection, then press to confirm. See table below for selection. 4 Hold to finish the procedure. Item Selectable setting (Pres ...

  • Kenwood KDC-4554U - page 10

    10 Start playing a disc 1 Press SRC to turn on the power. 2 Insert a disc into the loading slot. Playback starts automatically. 3 Press number button 6 ( ) to resume/pause playback (if necessary). Ejects the disc. (“NO DISC” appears and “IN” indicator goes off.) Loading slot Pr ess to select track/file. Hold to fast-forwards/reverses . List ...

  • Kenwood KDC-4554U - page 11

    11 ENGLISH Selecting Repeat Play Press number button 4 (REP) repeatedly to make a selection. Audio CD : TRACK/ TRAC (track) REPEAT, REPEAT OFF AAC/MP3/WMA : FILE REPEAT, FOLDER/ FOLD (folder) REPEAT, REPEAT OFF iPod : FILE REPEAT, REPEAT OFF Selecting Random Play Press number button 3 (ALL RDM) or repeatedly to make a selection. Audio CD : DISC RAN ...

  • Kenwood KDC-4554U - page 12

    12 About compatible iPod/iPhone Made for – iPod touch (1st, 2nd, 3rd, and 4th generation) – iPod classic – iPod with video – iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generation) – iPhone 4 – iPhone 3GS – iPhone 3G – iPhone For the latest compatible list and software version of iPod/iPhone, see: www.kenwood.com/cs/ce/ipod If you s ...

  • Kenwood KDC-4554U - page 13

    13 ENGLISH Preparation : Make sure [ON] is selected for [BUILT-IN AUX] / [BUILTIN AUX] . (page 7, 8) 3.5 mm stereo mini plug (commercially available) Portable audio device (commercially available) Auxiliary input jack Listening to the other external components 1 Press SRC to select “AUX.” 2 Turn on the external component and start playing. 3 Tu ...

  • Kenwood KDC-4554U - page 14

    14 Caution: Do not set the remote control in hot places such as on the dashboard. Lithium batter y . Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type. The battery pack or batteries shall not be exposed to excessive heat such sunshine , fire or the like. Keep batter y out of reach of children ...

  • Kenwood KDC-4554U - page 15

    15 ENGLISH 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [AUDIO CONTROL] / [AUDIO CTRL] or [SETTINGS] , then press to enter. 3 Turn the volume knob to make a selection, then press to confirm. See table below for selection. Repeat step 3 until the desired item is selected/activated. Press to return to the previou ...

  • Kenwood KDC-4554U - page 16

    16 [AUDIO CONTROL] / [AUDIO CTRL] : While listening to any source ex cept in ST ANDBY state... Item Selectable setting (Preset: *) DETAILED SET/ DETAIL SET LPF SUBWOOFER/ LPF SUB-W Except for : THROUGH *: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies higher than 85 Hz/ 120 Hz/ 160 Hz are cut off. SUB-W PHASE Except for : ...

  • Kenwood KDC-4554U - page 17

    17 ENGLISH [SETTINGS] Item Selectable setting (Preset: *) DISPLAY (for ) DISP DIMMER ON: Dims the display illumination. ; OFF *: Cancels. TEXT SCROLL AUTO */ ONCE: Selects to scroll the display information automatically, or scroll only once. ; OFF: Cancels. TUNER SET TI/ NEWS SET/ AF SET/ REGIONAL/ AUTO ATP SEEK/ ATP SEEK: Selectable only if any so ...

  • Kenwood KDC-4554U - page 18

    18 Symptom Remedy/Cause “COPY PRO” appears. A copy-protected file is played. “READ ERROR” appears. Copy the files and folders for the USB device again. If the error message is still displayed, initialize the USB device or use other USB devices. “NO DEVICE” appears. No USB device is connected. Connect an USB device, and change the source ...

  • Kenwood KDC-4554U - page 19

    19 ENGLISH Installation/connection Part list: A F aceplate.............................................................. (×1) B Escutcheon ......................................................... (×1) C Mounting sleeve ............................................. (×1) D Casing f or faceplate ...................................... (×1) E Wirin ...

  • Kenwood KDC-4554U - page 20

    20 Wiring connection FRONT RL REAR/SW RL REAR/SW REMOTE CONT STEERING WHEEL REMOTE INPUT MUTE P . CONT ANT CONT For : Fuse (10 A) Antenna terminal (JASO) Light blue/yellow (Steering remote control wire) To the steering wheel remote control adapter Blue/White (Power control wire/ Antenna control wire) Brown (Mute control wire) To the power control t ...

  • Kenwood KDC-4554U - page 21

    21 ENGLISH For : MUTE P . CONT ANT CONT Fuse (10 A) Antenna terminal (JASO) Blue/White Brown Blue To the terminal that is grounded when either the telephone rings or during conversation. (To connect the Kenwood navigation system, consult your navigation manual.) Car fuse box Car fuse box Battery Ignition key switch Red (Ignition wire) Yellow (Batte ...

  • Kenwood KDC-4554U - page 22

    22 Installing the unit Removing the unit 2 1 Connect the wiring harness to the unit. Other wiring connection has been completed earlier . (page 20, 21) Before attaching , make sure the direction of the escutcheon is correct. ( Wider hooks on the top side.) Dashboard of your car 1 Detach the faceplate. 2 Engage the catch pin on the removal tools int ...

  • Kenwood KDC-4554U - page 23

    23 ENGLISH FM tuner section Frequency range: FM1/ FM2/ FM3 (50 kHz space): 87.5 MHz — 108.0 MHz For : FM1/ FM2 (50 kHz space): 87.5 MHz — 108.0 MH z FM3 (30 kHz space): 65.00 MHz — 74.00 MH z Usable sensitivity (S/N= 26 dB): 1.0 μV/75 Ω Quieting sensitivity (DIN S/N = 46 dB): 2.5 μV/75 Ω Frequency response (±3 dB): 30 Hz — 15 kH z Sign ...

メーカー Kenwood カテゴリー Car Stereo System

Kenwood KDC-4554Uのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- KDC-4554Uの取扱説明書
- Kenwoodの製品カード
- パンフレット
- またはKenwood KDC-4554Uの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Kenwood KDC-4554Uの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Kenwood KDC-4554Uの取り付け説明書、サービスマニュアル、簡易説明書、またはKenwood KDC-4554Uのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Kenwood KDC-4554Uの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Kenwood KDC-4554Uデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKenwood KDC-4554Uを使用するのを助ける技術的文書のことです。説明書は通常、全てのKenwood KDC-4554Uユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Kenwoodの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Kenwood KDC-4554Uの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKenwood KDC-4554Uの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Kenwood KDC-4554Uに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Kenwood KDC-4554Uデバイスの基本機能を使うにあたってのヒント。 Kenwood KDC-4554Uのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Kenwood KDC-4554Uに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKenwood KDC-4554Uのメーカー/サービスへの連絡先に関する情報。

Kenwood KDC-4554Uについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKenwood KDC-4554Uの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKenwood KDC-4554Uで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)