-
Kenwood CX-SR10 - page 1
CX -SR1 0 Sirius ® Sat ellite Ant enna Installation Manual ©2002 Ken wood USA Corporation. All Rights Reserved. ...
-
Kenwood CX-SR10 - page 2
2 ...
-
Kenwood CX-SR10 - page 3
Introduction Y our Sirius satellit e antenna, appro ved by Sirius Satellit e Radio, Inc., has been spe- cially designed to receiv e signals from Sirius' three sat ellites and Sirius' network of ground-based "repeat er" transmitters. Figure 1: Ideal reception pattern Figure 2: Effect of obstruction on reception pattern Roof-Mount ...
-
Kenwood CX-SR10 - page 4
Mechanical data: Electrical data: General Instructions Satellit e antennas are e xtremely sensitive and finely specified to facilitat e reception of satellit e signals under a variety of conditions across the whole of North America. It is important to read these instructions carefully to ensure that the antenna is mounted pr operly in the best loca ...
-
Kenwood CX-SR10 - page 5
Shor tening the ant enna "tail" The antenna module is supplied with a 6 inch tail. F or vehicles with flat r oofs (SUVs, Mini-vans) and f or conv er tibles, it is possible to shorten the tail by up t o 2 inches. NOTE : For v v ehicles w w ith a a s s loping r r oof, o o r i i f t t he m m odule i i s m m ounted o o n t t he t t runk o o f ...
-
Kenwood CX-SR10 - page 6
Inst alling on Sedans The antenna module should be locat ed along the centerline of the r oof, at least 4 inches from the rear windo w . Figure 7: Installed antenna The antenna cables should be tuck ed and routed underneath the rubber molding around the rear windo w and into the trunk. Note: R outing the cable in the window molding will not af f ec ...
-
Kenwood CX-SR10 - page 7
Figure 9: Cables routed separately T wo types of windo w moldings (Outside and Encapsulated) are used on most vehi- cles. Both are suitable f or concealing the antenna cable. Figure 10: Outside rubber molding (most common) Figure 11: Encapsulated molding (less common) Note: The windo w molding will be more flexible and easier to work with at r oom ...
-
Kenwood CX-SR10 - page 8
Figure 12: Cables routed in standard molding 6. Route the cable from the lo west point of the rear window into the trunk area. T ake advantage of an y existing cable channel or wiring conduit. Figure 13: Entering the trunk through cable channel Figure 14 Cables routed directly through the molding and through the cable channel to the interior 8 ...
-
Kenwood CX-SR10 - page 9
7 . If there is no suitable cable channel, the cable may be rout ed directly from the window molding to the right or left corner of the trunk. Figure 15: Cable routing along the trunk rubber molding It may be necessary to remov e the plastic housings from the antenna connectors in order t o feed the cables thr ough narrow openings. Not e: Remember ...
-
Kenwood CX-SR10 - page 10
Inst alling on Conv er tibles On conv er tibles the antenna module should be locat ed on the centerline of the trunk appro ximately 6 inches fr om the rear window . W ARNING: Mounting the antenna on the trunk will only work with convertibles. For all other types of v ehicles mount the antenna on the roof. Figure 18: Mounted on trunk of convertible ...
-
Kenwood CX-SR10 - page 11
3. Drill a small hole or cut a gap into the rubber slee ve and lead the cable through the interior trim t o the receiver . Figure 21: Entering the interior through the cable channel Note: Man y convertibles have com posite trunk lids. In such cases it will be necessary to creat e a metal "ground plane". This can be done b y gluing aluminu ...
-
Kenwood CX-SR10 - page 12
Inst alling on SUVs, Miniv ans and 5-Door V ehicles The antenna module should be locat ed on the centerline of the r oof, not less than 4 inches from the gap betw een the roof and tailgat e: Figure 23: Minivan with Antenna Module Note t t he f f ollowing: • If the vehicle is eq uipped with a roof rack, the cr ossbar should be placed at least 6 in ...
-
Kenwood CX-SR10 - page 13
2. Route the cable be tween the roof and the tailgate t o the inside. T ake advantage of any e xisting cable channel or wiring conduit. 3. There are two alternativ e methods to rout e the cable under the headliner and to the receiver: a. The cable ma y be routed t o the cable channel, lif t up the channel and go through the small opening and push t ...
-
Kenwood CX-SR10 - page 14
Mounting on Pickup T rucks The antenna module should be mount ed on the centerline of the r oof appro ximately 4 inches from the rear of the cab. The cables ma y be routed into the cab thr ough the brake light ca vity. Figure 29: Pickup truck with antenna module 1. Follow st eps 1 to 4 under "Installing on Sedans" to attach the ant enna m ...
-
Kenwood CX-SR10 - page 15
1 5 ...
-
Kenwood CX-SR10 - page 16
Interne t www.kenwoodusa. com E -m m ail inquiry@kenwoodusa .com Telephon e 1 -8 8 0 0 -K K ENWOOD Main O O ffice P.O. B B ox 2 2 2745 Long B B each, C C A 9 9 0801 -5 5 745 ®2002 Ken wood USA Corporation. All rights reser ved. ...
Kenwood CX-SR10についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもKenwood CX-SR10の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKenwood CX-SR10で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。