日本語 dropdown-ico

Smeg SE70S-1の取扱説明書

16ページ 関係なし
ダウンロード

ページに移動 of 16

Summary
  • Smeg SE70S-1 - page 1

    Contents 1. INSTRUCTIONS FOR SAFE A ND PROPER USE _____________________ 22 2. POSITIONING OF HOB _________________________________________ 24 3. ELECTRICAL CONNECT ION _____________________________________ 26 4. GAS CONNE CTION ____________________________________________ 27 5. ADAPTATION TO DIFFER ENT TYPES OF GAS ______________________ 29 6. FINA ...

  • Smeg SE70S-1 - page 2

    Introduction 1. INSTR UCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP TH E SERIES OF NOZZLES SUPP ...

  • Smeg SE70S-1 - page 3

    Introduction THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECT LY SMO ...

  • Smeg SE70S-1 - page 4

    Instructions for the installer 2. POSITIONING OF HOB The following operation r equires buildi ng and/or carp entry work so must be carried out by a competent tradesman. Installation can be carried out on var ious materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Never use silicone o ...

  • Smeg SE70S-1 - page 5

    Instructions for the installer In case of installation on a holl ow compartment with doors, a separating panel has to be placed under the hob. Keep a minimum distance of 10 mm between the bottom of t he unit and the panel surface. The p anel has to be easily removable to allow acces s in the event of technical service. 25 ...

  • Smeg SE70S-1 - page 6

    Instructions for the installer 3. ELECTRICAL CONNECTION Make sure that the voltage and capacit y of the power l ine conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical system ...

  • Smeg SE70S-1 - page 7

    Instructions for the installer 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally. For this purpose, loos en hexagon nut B , ...

  • Smeg SE70S-1 - page 8

    Instructions for the installer 4.1 Connection to LPG Use a pressure regulator and make the con nection to the tank according to the provisions of stand ard s regulations in force. Make sure that feed pressure conforms to the lev els shown in the table in paragraph “5.2 Regulation for LPG”. 4.2 Ventilation of rooms The hob may be installed only ...

  • Smeg SE70S-1 - page 9

    Instructions for the installer 5. AD APT A TI ON T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other ty pes of gas the nozzles must be replaced and the primary air adju ...

  • Smeg SE70S-1 - page 10

    Instructions for the installer 5.2 Regulation for LPG Loosen screw A and push supp ort B all the w ay. Use a double head wrench to remove nozzle C a nd assemble the suitable one, following t he instructions indicated in the referenc e charts, with respect to the type of gas to use. The screwing t orque of the nozzle should never exceed 3 Nm . Repos ...

  • Smeg SE70S-1 - page 11

    Instructions for the installer 5.3 Regulation for natural gas The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work wit h this type of gas, perform the same operations described in paragraph “5.2 Regulation for LPG”, but choos e the nozzles and regulate the primary ai r for natural gas, as show ...

  • Smeg SE70S-1 - page 12

    Instructions for the installer 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the instructi ons in paragraph “5.1 Removing the hob”. 6.1 Regulation of minimum for natural gas Replace the co mponents on the burner and slide the knobs on the gas tap pins. Light the burner and set it ...

  • Smeg SE70S-1 - page 13

    Instructions for the installer 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Average rapid 4 Large rapid 5-6 Triple crown 7 Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualified technici ...

  • Smeg SE70S-1 - page 14

    Insructions for the user 7. USING THE HOB Make sure that the fl ame-baffle crowns, the caps and the gr id have been assembled correctly. Grid C (supplied) should be used for "woks" (Chinese pots). Adapter B (supplied) is to be used for small vessels. 7.1 Ignition of the burners with safety device For each knob the c orresponding burner is ...

  • Smeg SE70S-1 - page 15

    Insructions for the user 7.3 Diameter of containers BURNERS 1 Auxiliary 2 Semi-rapid 3 Average rapid 4 Large rapid 5-6 Triple crown 7 Double crown Ø min. e max. (in cm) 7-18 10-24 12-24 14-28 22-26 12-34 7.4 Using a griddle plate A few precautions are necessary if you wish to use a griddl e plate: • leave a gap of at le ast 160 mm between the ed ...

  • Smeg SE70S-1 - page 16

    Insructions for the user 8. CLEANING AND MAINTENANCE NEVER USE A STEAM JET TO CLEAN THE APPLIANCE. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regular ly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su rface ...

メーカー Smeg カテゴリー Stove

Smeg SE70S-1のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SE70S-1の取扱説明書
- Smegの製品カード
- パンフレット
- またはSmeg SE70S-1の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Smeg SE70S-1の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Smeg SE70S-1の取り付け説明書、サービスマニュアル、簡易説明書、またはSmeg SE70S-1のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Smeg SE70S-1の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Smeg SE70S-1デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSmeg SE70S-1を使用するのを助ける技術的文書のことです。説明書は通常、全てのSmeg SE70S-1ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Smegの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Smeg SE70S-1の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSmeg SE70S-1の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Smeg SE70S-1に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Smeg SE70S-1デバイスの基本機能を使うにあたってのヒント。 Smeg SE70S-1のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Smeg SE70S-1に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSmeg SE70S-1のメーカー/サービスへの連絡先に関する情報。

Smeg SE70S-1についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもSmeg SE70S-1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSmeg SE70S-1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)