-
Siemens IGWIPS200-1 - page 1
INSTALLATION GUIDE IGWiPS200-1 Rev 3 May 2007 ) ) ) ) ) ) ) ) ) ) ) ( ( ( ( ( ( ( ( ( ( ( ( WiPS-200 Series Wireless Process Solution Frequency Hopping Spread Spectrum Radio Two-Way (Multipoint-to-Point) for Monitoring and Control With Expandable I/O Options ...
-
Siemens IGWIPS200-1 - page 2
...
-
Siemens IGWIPS200-1 - page 3
IGWiPS200-1 TABLE OF CONTENTS SECTION TITLE PAGE PREFACE ........................................................................................................................ ............................. 2 CONVENTIONS AND SYM BOLS ........................................................................................................ .......... ...
-
Siemens IGWIPS200-1 - page 4
IGWiPS200-1 PREFACE CONVENTIONS AND SYMBOLS The followin g symbols m ay be used in this manual and may appear on the equi pment. The reader should becom e familiar with the symbols and their meaning. Symbols are provided to quickly alert the reader to safety related text. Symbol Meaning DANGER Indicates an immediate hazardous situation which, if no ...
-
Siemens IGWIPS200-1 - page 5
IGWiPS200-1 • For devices with explosion protection: trai ning, instruction or authorization to work on electrical circ uits for systems that could cause explosions. • Training or instruction according to the safety sta ndard s in the care and use of suitable safe ty equipment. SCOPE This manual does not purp ort to cove r all detail s or varia ...
-
Siemens IGWIPS200-1 - page 6
IGWiPS200-1 INTRODUCTION This publication describes installation of the Siemens Wireless Process Solution (WiPS) 200 Seri es Two-W ay Multipoint- To-Point Radios and I/O Expansio n Modules. R adios (i.e. tra nsceivers) 1 and I/O modules ar e used to const ruct a WiPS wi reless network fo r the gathering a nd distrib ution of pr o cess related analo ...
-
Siemens IGWIPS200-1 - page 7
IGWiPS200-1 Each transceiver and each I/O Expansion m odule has bus conn ectors on both sides of its c over: a male connector on one side, a female connector on the other. A transceiver and several I/O Expansio n modules can be physically interconnected by way of th eir bus conn ectors and then snapped onto a sect i on of DIN rail as a single unit. ...
-
Siemens IGWIPS200-1 - page 8
IGWiPS200-1 PRODUCT SUPPORT When contacting Siemens for support: • Please have co mplete product information at hand: • For hardware, this information is provid ed on the product nameplate (part num ber or model n umber, serial num ber, and/or ve rsion). • For most software, this information is given in the Help > About screen. • If ther ...
-
Siemens IGWIPS200-1 - page 9
IGWiPS200-1 INSTALLATION This section provi des installation proce dures for a WiPS 200 Series wirel ess network. A wireless net work contains a master transcei ver and up to e ight remote (i .e. slave) transcei vers. I/O Expansi on modules pr ovide the network wi th additional analog, digital, and pulse I/O ca pacity. Trans ceivers a nd I/O module ...
-
Siemens IGWIPS200-1 - page 10
IGWiPS200-1 DANGER Electrical shock hazard Explosion hazard Will cause death or injury. • Remove power from all wires and termin als before working on equipment. • In a potentially hazardous atmosphe re, remove power from equipment before connecting or disconne cting power, signal, or other circuit. • Observe all pertinent regulation rega rdi ...
-
Siemens IGWIPS200-1 - page 11
IGWiPS200-1 Changes or modifications not ex pressly approved by Si emens will void the user’s authority to operate the equipment . This product is intended fo r fixed installation applications . In order to co mply with FCC/ISC adopted RF exposure requirements, installation of this transmitter system’s an tenna must be performed in a manner tha ...
-
Siemens IGWIPS200-1 - page 12
IGWiPS200-1 ANTENNA CON NECT OR S AND S URGE VOLTAGE PROTECTION Each transceive r has an MCX fem ale antenna connect or. The base 3-1/2" , 1/4-wave whip antenna has a n MCX mal e connector. Opt ional higher ga in antennas an d low-loss co axial cables have type-N connectors. MCX to type-N adapters and other connecto r adapters are available. O ...
-
Siemens IGWIPS200-1 - page 13
IGWiPS200-1 Control Room At the contr ol room, there is one master t ransceiver and c omplementi ng I/O: one analog output m odule, and one digital out put modul e. The total curre nt requirem ent is 287 m A [75 mA +100 m A + 32 m A + (4 x 20 m A)]. Table 2 WiPS Module Bus Current Requirements Module Bus Current Requirement (in mA @ 24 Vdc) Transce ...
-
Siemens IGWIPS200-1 - page 14
IGWiPS200-1 A. Analog Output and Digital Output Fault Respon se Selections Three I/O m odules (4-Cha nnel Analog Output Mod ule, 8-Channel Digital Out put Module , and Combi nation Input/Output Module) cont ain DIP switc hes that may be set by the user to det ermine the m odule’s response to the connected transceiver’s loss of an RF Link or to ...
-
Siemens IGWIPS200-1 - page 15
IGWiPS200-1 Pulse Output Module (See Figure 18 on page 26) There are two DIP s witches for each channel: switches 1 a n d 2 for channel 1, switche s 3 and 4 for channel 2. Switches 1 (CH1) and 3 (CH2 ) – Co unte r or Frequency Mode; Default se tting is Counter When Counter m ode is selected, the module will output a specific number of pulses as d ...
-
Siemens IGWIPS200-1 - page 16
IGWiPS200-1 MOUNTING THE DIN RAIL At each installation site, mount the DIN rail and DIN rail mount modules (e.g. tra nsceiver, I/O modules, powe r supply) in a NEMA enclosure appropriat e for the environment and hazardous ar ea classification. Re fer to Figure 3 for transceive r and I/O m odule dime nsions. Allow r oom for: o Physically mounting an ...
-
Siemens IGWIPS200-1 - page 17
IGWiPS200-1 Each module h as a moveable, sp ring-loaded m ounting li p to assist in m ounting a m odule, sliding a module along the DIN rail, and removing a module from the DIN rail. This lip has a slotted tab so the blade of a small screwdriver can be inserted and the lip levered away from the rail. Figure 4 Module Features To mount a ro w of up t ...
-
Siemens IGWIPS200-1 - page 18
IGWiPS200-1 MOUNTING THE 1/4-WAVE WHIP ANTENNA Mount the 3-1/6" (80. 4 mm) high, omnidirect ional whip a ntenna 5 , sh own at right, within 5' (1. 5m) of the transceiver to allow the supplied 6' (2m) cable to easily reach between the antenna and transceiver. A mounting bracket and t hree screws are supplied. Ante nna spacing (transmi ...
-
Siemens IGWIPS200-1 - page 19
IGWiPS200-1 Electrical Connections – Power and I/O connections are completed through screw actuated compression terminals. Connector bl ocks can be rem oved from a m odule for wiri ng, as shown i n the two fig ures below. Insert a small straight-slot sc rewdriver bet ween a connecto r block and the faceplate and use a gentle pry ing motion t o se ...
-
Siemens IGWIPS200-1 - page 20
IGWiPS200-1 Transceiver Wiring Examples Five transceive r wiring exam ples are provide d below. Figures 6 , 7, and 8 s how typical transceive r wiring for 2-wire, 3-wire, and 4-wir e current loops. Figures 9 and 10 show two variatio ns on the wiring for a loop powered external analog device. Also shown in Figures 9 and 10 is the wirin g for an RF L ...
-
Siemens IGWIPS200-1 - page 21
IGWiPS200-1 Figure 7 Transceiver Wiring, 4-20 mA Curren t Loop with 3-Wire Device May 2007 19 ...
-
Siemens IGWIPS200-1 - page 22
IGWiPS200-1 Figure 8 Transceiver Wiring, 4-20 mA Curren t Loop with 4-Wire Device May 2007 20 ...
-
Siemens IGWIPS200-1 - page 23
IGWiPS200-1 Figure 9 Transceiver Wiring, Analog and Digital Outpu ts Figure 10 Transceiver Wiring, Analog Outpu t Wirin g for a Loop Powered Device May 2007 21 ...
-
Siemens IGWIPS200-1 - page 24
IGWiPS200-1 Transceiver RF Link and Output State Wiring Option s This section de scribes the tran sceiver RF link status relay and t he analog ou tput and di gital output wi ring optio ns. A block diag ram of the transcei ver is shown i n Figure 11. Figure 11 Transceiver Block Diagram Transceiver RF Li nk The RF Link relay has Form A, Normally Open ...
-
Siemens IGWIPS200-1 - page 25
IGWiPS200-1 Green Faceplate Figure 12 4-Channel Analog Input Module Wiring Yellow Faceplate Figure 13 4-Channel Analog Output Module Wiring May 2007 23 ...
-
Siemens IGWIPS200-1 - page 26
IGWiPS200-1 Blue Faceplate Figure 14 8-Channel Digital Input Module Wiring Pink Faceplate Figure 15 8-Channel Digital Output Module Wiring May 2007 24 ...
-
Siemens IGWIPS200-1 - page 27
IGWiPS200-1 Multiple Colors Faceplate Figure 16 Combination Input and Output Module Wiring (One Analog Input, One Analog Output, T wo Digital Inputs, and Two Digital Outputs) May 2007 25 ...
-
Siemens IGWIPS200-1 - page 28
IGWiPS200-1 Orange Faceplate Figure 17 2-Channel Pulse Input Module Wiring Orange Faceplate Figure 18 2-Channel Pulse Output Module Wiring May 2007 26 ...
-
Siemens IGWIPS200-1 - page 29
IGWiPS200-1 ASSIGNING AND SETTING I/O MODULE ADDRESSES Module addres ses are 1 through 8, as shown on the m odule faceplates i n Figure 19. T he top row in the f igure shows three I/O modules at a location (for example, at a remote location). T he lower row shows the complementary I/O modules at ano ther location (for exam ple, at the contr ol room ...
-
Siemens IGWIPS200-1 - page 30
IGWiPS200-1 HAZARD LABEL A label, similar to that shown here, is included in a WiPS shipment. The installer or user should post this label in an appropriate, high ly visible location near the WiPS modules. Possi ble label m ounting locations include: on the out side of an encl osure housing WiP S modules or in side that enclos ure adjacent to the m ...
-
Siemens IGWIPS200-1 - page 31
IGWiPS200-1 4. Locate the Hop Key (a small circuit bo ard) at the rear edge of th e top circuit board , see the figure below . Unplug the Hop Key and set it aside. Hop Key Location 5. Carefully insert the faceplate/circu it boa rd assembly in its cover until it snaps int o place. When inserting the assembly into its cover, be sure the circuit board ...
-
Siemens IGWIPS200-1 - page 32
IGWiPS200-1 0.0 1.0 2.0 3.0 4.0 -115 - 110 -10 5 -100 -95 -90 -85 -8 0 -75 Signal S trength (-dBm ) +DC Volts RSSI vs DC Voltage MG0044 6a Figure 21 Received Signal Strength Graph TRANSCEIVER AND I/O EXPANSION MODULE STATUS LED INDICATIONS Power LED Indicates the presence of power to the m odu le. It is ON when p ower is present and OFF when there ...
-
Siemens IGWIPS200-1 - page 33
IGWiPS200-1 PULSE OUTPUT MODULE DIAG NOS TIC LED’S There are 3 dia gnostic LED’s on the pulse out put module: Status LED: On solid when I/ O is functional and flashing if there is a confl ict with anothe r module. Pulse Input 1 and 2 LEDs: These lights will flicker at a varying frequency depending on the frequency of pulses being generated: Fre ...
-
Siemens IGWIPS200-1 - page 34
IGWiPS200-1 Digital Input Module Channels ............................................................... 8 Digital Input Voltage Range ................................. 5 to 30 Vac/Vd c, re verse polarity protected Input Impedance ................................................... 20k Ohms Input Frequency ......................................... ...
-
Siemens IGWIPS200-1 - page 35
IGWiPS200-1 Combination Input/Output Module Channels ............................................................... 1 an alog input 1 analog output 2 digital inputs 2 digital outputs Channel Isolation .................................................. A ll (except for the anal og input chan nel) Reverse Polarity Protection ........................ ...
-
Siemens IGWIPS200-1 - page 36
IGWiPS200-1 WARRANTY (a) Seller warrants that on the date of shipment the goods are of the k ind and quality described herein and are free of non-conform ities in workm anship and m aterial. This wa rranty does n ot apply to go ods delivered by Seller but manufacture d by others. (b) Buyer' s exclusive rem edy for a nonc onformity in any item ...
Siemens IGWIPS200-1についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもSiemens IGWIPS200-1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSiemens IGWIPS200-1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。