Graco 287834の取扱説明書

12ページ 0.94 mb
ダウンロード

ページに移動 of 12

Summary
  • Graco 287834 - page 1

    311485J EN Operation Displacement Pump - Use with Arc hitectural Coati ngs, P aints, R oof Coatings and Below Grade Coatings - Model 287834 4000 psi (27 .6 MP a, 275.8 bar) Maximum W orking Pressu re Impor tant Safety Instructions Read all warnings and instructions in this manual. Sa v e these instructions. ti7629a ...

  • Graco 287834 - page 2

    Warnings 2 311485J Wa r n i n g s The f ollowing w arnings are for the set up, use, groun ding, maintenance, and repair of this equipment. The e xclama- tion point symbol ale r ts you to a general w arning and the hazard symbols ref er to procedur e-specific risks. When these symbols appear in the body of this man ual, ref er ba c k to these W arni ...

  • Graco 287834 - page 3

    Operation 311485J 3 Operation Pressure Relief Pr ocedure 1. Set pump v alve OFF . T ur n engine OFF . 2. T ur n pressure to low est setting. T rigger gun into pail to reliev e pressure. 3. Open prime v alv e (v er tical). If you suspect that the spray tip or hose is complet ely clogged, or t hat pressur e has no t been fully reliev ed after f ollow ...

  • Graco 287834 - page 4

    Service 4 311485J Service Remo va l 1. Flush pump (36). Stop pump on down stroke if pos- sible . 2. P erform Pressure Relief Pr ocedure , page 3. 3. Remove suction set ( 147) from pump (36). 4. Remove paint and drain lines from filter housing. 5. Using a wrench, loosen filter hou sing fitting (110) and remove housing fr om pump. 6. Using a pliers, ...

  • Graco 287834 - page 5

    Service 311485J 5 8. Separate coupling (125) and re mov e. 9. Using a hammer , loosen jam nut ( 122). Unscre w pump (36 ) from po wer head. 10. Remove pump (36). Ball Adjustment 1. Using a hammer , loosen and remo v e intake v alve (213). 2. Disassemb le and clean all parts and o-rings (207). 3. Select proper ba ll travel for material spra yed. Rea ...

  • Graco 287834 - page 6

    Service 6 311485J Piston Rod Assembl y 1. T ap piston rod out of cylinder with a hammer or flip ov er and tap piston rod out against ben ch. NO TE: Slee v e ma y come out of cylinder with piston rod. 2. If piston rod and sleeve did not separate, invert pis- ton rod ( 222) and sleeve (220) and po und on hard surface until piston rod comes out of sle ...

  • Graco 287834 - page 7

    Service 311485J 7 3. Grease piston rod (2 22) packings and top edge of sleeve (220). 4. Carefully slide piston rod assembly (222) into top edge of slee ve (220). 5. Grease top inch or two of piston rod (222) that will go throug h the cylinde r throat packings. 6. Grease o-ri ng (207) and place on sleeve . Slide one o-ring (207) inside cylinder (205 ...

  • Graco 287834 - page 8

    Service 8 311485J 10. Reassemb le intake valve (2 13) as shown. 11. P lace inta ke valve (213) assembly in vice. Install cylinder (205) assembly to intake va lve. Torque to 350 ft-lb (475 N•m). 12. Torq ue packing nut (202) do wn to 50 ft-lb (6 8 N•m). 13. Screw jam nut (12 2) to bottom of pu mp threads (36). Screw pump com pletely up into powe ...

  • Graco 287834 - page 9

    Service 311485J 9 17. Replace clip pin ( 121) to secure. 18. Reinstall filte r housing (110 ). 19. Connect suction hose (147) to pump outlet (3 6). 121 125 ti7809a ti7772a 110 ti7764a 36 147 ...

  • Graco 287834 - page 10

    Parts 10 311485J Pa r t s Ref. P a rt Description Qty . 201* 116385 PLUG 1 202 15G198 NUT , p acking 1 203* 15G285 V -P ACKING, UHMWPE, b lue 3 204* 15H250 GLAND , male, th roat 1 205 2878 36 CYLINDER, pump 1 206* 102972 BAL L, sst, 0.875 in. 1 207*† 116377 P A CKING, o-ring 3 208 15G196 GUIDE, ball 1 209 1973 06 SHIM, inlet 3 210 287837 V AL VE, ...

  • Graco 287834 - page 11

    Notes 311485J 11 Notes ...

  • Graco 287834 - page 12

    All written and visual data con tained in th is document reflects the late st product information availabl e at the time of publica tion. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents. Original instructions. This manual conta ins English. MM 311485 Graco Headquarters: Minneapo ...

メーカー Graco カテゴリー Septic System

Graco 287834のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 287834の取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco 287834の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco 287834の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco 287834の取り付け説明書、サービスマニュアル、簡易説明書、またはGraco 287834のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco 287834の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco 287834デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco 287834を使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco 287834ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco 287834の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco 287834の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco 287834に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco 287834デバイスの基本機能を使うにあたってのヒント。 Graco 287834のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco 287834に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco 287834のメーカー/サービスへの連絡先に関する情報。

Graco 287834についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco 287834の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco 287834で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)