-
Simplicity 1694918 - page 1
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T win Catcher Mfg. No. Description 1694918 Clean Sweep Triple Catcher 1732353 Rev. 00 Rev. Date 02/2006 TP 100-4265-00-AT-SMAN Clean Sweep T riple Catc her ...
-
Simplicity 1694918 - page 2
...
-
Simplicity 1694918 - page 3
1 Normal Remov al & Installation Collector Installation ......................................10 Collector Remov al .........................................11 NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position. Safety Rules & Inf ormation General W ar nings .......................... ...
-
Simplicity 1694918 - page 4
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This u ...
-
Simplicity 1694918 - page 5
Bef ore Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i ...
-
Simplicity 1694918 - page 6
Initial Installation 4 Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). W ARNING Figure 1. Install Spacer (left side shown) A. Speed Nut, 5/16-18 B. Threaded Side C. Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support B C D A A E Initial Installation HIT ...
-
Simplicity 1694918 - page 7
5 T ube Component Assembly Baffle Installation 1. Determine which baffle to use. See Figure 3 Chart. 2. Lift side discharge chute (H, Figure 3). 3. Insert baffle (F) through discharge opening and posi- tion baffle into place. 4. Tighten carriage bolts (A) and nuts (E) on baffle (F). 5. Tighten carriage bolt (B) and nut (E) on baffle (F). 6. Positio ...
-
Simplicity 1694918 - page 8
6 Baffle Installation Figure 5. Lower Chute to Boot Installation A. Pin, Latch B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 D. Lower Chute E. Locknut, Center Lock, 5/16-18 F. Strap, Rubber G. Locknuts, Whiz Lock, 5/16-18 H. Rod, Boot Mount I. Capscrew, Hex Head, 5/16-18 x 1-1/4 J. Capscrew, Hex Head, Thin, 5/16-18 x 1 D B C F A G G H I J E LOW ...
-
Simplicity 1694918 - page 9
Install Latch & Hinge 7 Figure 7. Install Latch & Hinge to Cover Assembly A. Cover Assembly B. Latch C. Locknuts, ESNA, #10-24 D. Screws, #10-24 x 5/8 E. Hinge F. Locknuts, 1/4-20 G. Screws, Slotted, 1/4-20 x 1/2 Figure 8. Install Channel Assembly A. Channel Assembly B. Hitch C. Pin C B A A C INSTALL LATCH AND HINGE TO COVER ASSEMBLY 1. Ins ...
-
Simplicity 1694918 - page 10
Initial Hitch & T ube Installation 8 A Figure 11. Install Cover to Channel Assembly A. Cover B. Pin C. Hair Pin D. Channel Assembly C C B Figure 10. Install Tubes and End Caps A. Cross Bar B. Tubes C. Capscrews, 5/16-18 x 2 D. Locknuts, Center Lock, 5/16-18 E. Square End Plugs F. Round End Plugs E D F B F C F B F C F C F D D E D A INSTALL TUBES ...
-
Simplicity 1694918 - page 11
9 T ube Installation C D E A B Figure 14. Install Lower Tube A. Lower Chute Rod B. Mounting Plate C. Rubber Strap D. Discharge Deflector E. Locknut LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 14). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole clos- est to knob in str ...
-
Simplicity 1694918 - page 12
Normal Removal & Installation 10 A. Channel Assembly K. Lower Chute Rod B. Cover L. Lower Chute C. Pin M. Pin D. Hitch N. Strap, Middle E. Bag O. Upper Tube F. White Bar P. Ridge G. Nut & Capscrew Q. Ridge Cutout H. Deflector R. Tubes, Bag Support I. Strap, Boot S. Middle Tube J. Mounting plate E P D B Normal Remo val & Installation Col ...
-
Simplicity 1694918 - page 13
Normal Removal 11 Collector Remov al 1. Unhook strap (N) from pin (M). Slide middle tube into upper tube (O) and remove middle tube (S). Remove upper tube (O) from cover (B). 2. Lift up cover (B) remove and empty bags (E). 3. Unhook strap (I) from locknut and capscrew (G). Remove lower chute (L) from mounting plate (J). See that the discharge defle ...
-
Simplicity 1694918 - page 14
...
-
Simplicity 1694918 - page 15
...
-
Simplicity 1694918 - page 16
Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Snapper.com © Copyright 2006 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Port Washington ...
Simplicity 1694918についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSimplicity 1694918の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSimplicity 1694918で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。