日本語 dropdown-ico

Yard Machines 340 Thru 390の取扱説明書

24ページ 2.73 mb
ダウンロード

ページに移動 of 24

Summary
  • Yard Machines 340 Thru 390 - page 1

    IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 FR ONT TINE TILLERS Models 340 Thru 390 PRINTED IN U .S.A. FORM NO . 770-8576A O PERA T OR’S M ANU AL Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved for ...

  • Yard Machines 340 Thru 390 - page 2

    2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TILLER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESUL ...

  • Yard Machines 340 Thru 390 - page 3

    3 • Only use accessories approved for this machine by the manufacturer. Read, understand, and follow all instructions provided with the approved accessory. • If situations occur which are not covered by this manual, use care and good judgment. Contact your dealer for assistance. 2. CHILDREN • Tragic accidents can occur if the operator is not ...

  • Yard Machines 340 Thru 390 - page 4

    4 SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new tiller. It will help you assemble, prepare and maintain your tiller. Please read and understand what it says. Before you start to prepare your tiller for its first use, please locate the model plate and copy the information from it in this Operators Man ...

  • Yard Machines 340 Thru 390 - page 5

    5 A TT A CHING THE T AILPIECE AND DEPTH ST AKE Remove the two self-tapping screws on the frame. Slide the tailpiece into the frame, with the lower hole in the tailpiece toward the front. Secure with screws just removed. (See Figure 3.) Figure 3 A TT A CHING THE HANDLE ASSEMBL Y 1. Remove the hex bolt and cupped washer from the top right side of the ...

  • Yard Machines 340 Thru 390 - page 6

    6 A TT A CHING THE CLUTCH CONTR OL CABLE(S) FORWARD CABLE Attach the end of the forward cable to the bracket underneath the handle assembly as follows. (On model 390, the forward clutch cable is the cable which is attached closer to the rear of the tiller). 1. Loosen the hex nut on the threaded rod near the end of the cable, and move it up the rod ...

  • Yard Machines 340 Thru 390 - page 7

    7 SECTION 6: CONTROLS THRO TTLE CONTROL The throttle control lever is located on the engine. It controls the engine speed and stops the engine. (See Figure 9.) CHOKE LEVER (Model 340/390) The choke lever is located above the throttle control. It is used to enrich the fuel mixture when starting a cold engine. (See Figure 9). PRIMER BUTT ON (Model 34 ...

  • Yard Machines 340 Thru 390 - page 8

    8 Model 345 1. Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug. 2. Make certain all controls are in the neutral position (released). (See Figure 8). 3. Place the engine speed control in the START position. 4. Push primer t ...

  • Yard Machines 340 Thru 390 - page 9

    9 2. Depth Stake Adjustment: The depth stake acts as a brake for the tiller and controls the depth and speed at which the machine will operate. Remove the clevis pin and hairpin clip to raise or lower depth stake. (See Figure 10.) By increasing the depth of the depth stake, the forward speed of the machine is reduced, and the working depth is incre ...

  • Yard Machines 340 Thru 390 - page 10

    10 With the outer tines installed, the working width of the machine is 22 or 24 inches. For cultivation, this may be reduced to 13 inches by removing the outer tines. Refer to Tine Width Adjustment in Adjustment section. When laying out plant rows, be sure to allow enough width to permit cultivation between the rows. In growing corn or similar crop ...

  • Yard Machines 340 Thru 390 - page 11

    11 CARBURET OR ADJUSTMENT WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), disengage all clutches and tines. Keep clear of all moving parts. Be careful of heated surfaces and muffler. Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If ...

  • Yard Machines 340 Thru 390 - page 12

    12 Figure 19 Model 390 Shown . Figure 20 Model 390 Shown 6. Reassemble the new belt, following instructions in reverse order. Make certain the reverse drive belt is assembled with the wide side of the belt against the transmission and engine pulleys. Be certain to adjust the clutch control as instructed in the final clutch adjustment section of ass ...

  • Yard Machines 340 Thru 390 - page 13

    13 SECTION 12: TROUBLE SHOOTING GUIDE Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Throttle control le ver not in correct star ting position (if so equipped). Block ed fuel line. Dir ty aircle ...

  • Yard Machines 340 Thru 390 - page 14

    14 Model 340-345 ...

  • Yard Machines 340 Thru 390 - page 15

    15 Model 340-345 REF . NO . P ART NO . CODE DESCRIPTION 2 712-3004A He x Flange L-Nut 5/16-18 Thd. (Gr . 5) 3 786-0004 T ail Piece Br kt. (R.H.) 4 786-0003 T ail Piece Br kt. (L.H.) 5 710-0805 He x Bolt 5/16-18 x 1.5" Lg. 7 750-0890 Spacer .32" I.D . x .75" O .D . 8 786-0005 Depth Bar 9 711-0415 Cle vis Pin .375" I.D . x 1.62&qu ...

  • Yard Machines 340 Thru 390 - page 16

    16 Model 340-345 ...

  • Yard Machines 340 Thru 390 - page 17

    17 Model 340-345 REF . NO . PA R T NO . CODE DESCRIPTION 1 786-0056 Belt Cov er 2 736-3020 Fl-W ash. .266" I.D . x .625" O.D . 3 710-0599 He x Wash. Hd. TT -T ap Scr . 1/4-20 x .5" Lg. 4 712-0392 He x L-Stop Nut 1/4-28 Thd. 5 712-3004A He x Flange T op L-Nut 5/16-18 Thd. 6 786-0035A Tine Shield 7 710-0118 He x Bolt 5/16-18 x .75" ...

  • Yard Machines 340 Thru 390 - page 18

    18 Model 390 ...

  • Yard Machines 340 Thru 390 - page 19

    19 Model 390 REF . NO . P ART NO . CODE DESCRIPTION 2 712-3004A Hex Flange L-Nut 5/16-18 Thd. (Gr . 5) 3 786-0004 T ail Piece Br kt. (R.H.) 4 786-0003 T ail Piece Br kt. (L.H.) 5 710-0805 Hex Bolt 5/16-18 x 1.5" Lg. 7 750-0890 Spacer .32" I.D . x .75" O .D . 8 786-0005 Depth Bar 9 711-0415 Clevis Pin .375" I.D . x 1.62" Lg. ...

  • Yard Machines 340 Thru 390 - page 20

    20 Model 390 ...

  • Yard Machines 340 Thru 390 - page 21

    21 Model 390 REF . NO . PA R T NO . CODE DESCRIPTION 1 786-0057 Belt Cov er 2 736-3020 Fl-W ash. .266" I.D . x .625" O.D . 3 710-0599 He x Wash. Hd. TT -T ap Scr . 1/4-20 x .5" Lg. 4 712-0392 He x L-Stop Nut 1/4-28 Thd. 5 712-3004A He x Flange T op L-Nut 5/16-18 Thd. (Gr . 5) 6 786-0035A Tine Shield 7 710-0118 He x Bolt 5/16-18 x .75 ...

  • Yard Machines 340 Thru 390 - page 22

    22 NOTES ...

  • Yard Machines 340 Thru 390 - page 23

    23 NOTES ...

  • Yard Machines 340 Thru 390 - page 24

    MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty covers u ...

メーカー Yard Machines カテゴリー Tiller

Yard Machines 340 Thru 390のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 340 Thru 390の取扱説明書
- Yard Machinesの製品カード
- パンフレット
- またはYard Machines 340 Thru 390の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Yard Machines 340 Thru 390の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Yard Machines 340 Thru 390の取り付け説明書、サービスマニュアル、簡易説明書、またはYard Machines 340 Thru 390のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Yard Machines 340 Thru 390の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Yard Machines 340 Thru 390デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがYard Machines 340 Thru 390を使用するのを助ける技術的文書のことです。説明書は通常、全てのYard Machines 340 Thru 390ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Yard Machinesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Yard Machines 340 Thru 390の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははYard Machines 340 Thru 390の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Yard Machines 340 Thru 390に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Yard Machines 340 Thru 390デバイスの基本機能を使うにあたってのヒント。 Yard Machines 340 Thru 390のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Yard Machines 340 Thru 390に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるYard Machines 340 Thru 390のメーカー/サービスへの連絡先に関する情報。

Yard Machines 340 Thru 390についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもYard Machines 340 Thru 390の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがYard Machines 340 Thru 390で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)