-
Quantum Audio 3A Series - page 1
SuperLoader 3A Series SuperLoader™ 3A Series Quick S t art Guide The Quantum ® SuperLoader™ 3A Series autoloader is an automated storage and retrieval device with an in tegrated A -Series tape drive and up to two tape magazines holding up to ei ght cartridges each. It has a built- in FTP server and Web interface. For more information, see the ...
-
Quantum Audio 3A Series - page 2
2 Preparing for the Installation SuperLoader™ 3A Series Quick St art Guide Choose a location that meets the following criteria: Preparing for the Inst allation Before you begin the installation procedure in this section, make the following preparations as described in this section: • Providing Necessary Tools • Taking ESD Precautions • Prep ...
-
Quantum Audio 3A Series - page 3
Preparing for the Installation 3 SuperLoader 3A Series T aking ESD Precautions 0 Some components within the autoloader contai n static-sensitive parts. To avoid damaging these parts while performing ins tallation procedures, always observe the following precautions: • Ensure that the work area is free fr om conditions that could cause electrostat ...
-
Quantum Audio 3A Series - page 4
4 Unpacking the Autoloader SuperLoader™ 3A Series Quick St art Guide Unp acking the Autoloader Before you begin, clear a desk or table so that you can unpack the autoloader. The SuperLoader 3A Series Quick Start Guide has all the necessary information to unpack and inspect your autoloader correctly. You also need to select an open 2U computer rac ...
-
Quantum Audio 3A Series - page 5
Unpacking the Autoloader 5 SuperLoader 3A Series Checking Accessories 0 The following accessories are shipped with the S uperLoader 3A Series au toloader: • SuperLoader 3A Series Quic k Start Guide •E t h e r n e t c a b l e • Hardware to rack mount the autoloader (see figure 1 ) • Four autoloader brackets (two long a nd two short to accomm ...
-
Quantum Audio 3A Series - page 6
6 Rack Mounting the Autoloader SuperLoader™ 3A Series Quick St art Guide Rack Mounting the Autoloader This section provides the steps for atta ching the autoloader di rectly to the s tationary rails of a rack. Refer to table 1 for information on common rack hole types. T able 1 Rack Hole T ypes 1 Install two clip nuts, 1.75 in. (44.45 mm) apart, ...
-
Quantum Audio 3A Series - page 7
Rack Mounting the Autoloader 7 SuperLoader 3A Series Figure 2 Installing T w o Clip Nuts 2 Select the long or short autoloader brackets (depending on the depth of the rack), and then attach them to the rear of the autoloader (see figure 3 ). Use the long autoloader brackets (72-A226-A) when the distance from the front mounting rail to the rear moun ...
-
Quantum Audio 3A Series - page 8
8 Rack Mounting the Autoloader SuperLoader™ 3A Series Quick St art Guide Figure 3 Attaching Autoloader Brackets 3 Using rack screws, attach a support bracket to the clip nuts on each rear rail (see figure 4 .) Tighten the screws just enough to hold the support brackets firmly against the rail while still allowing the support bracket to be slightl ...
-
Quantum Audio 3A Series - page 9
Rack Mounting the Autoloader 9 SuperLoader 3A Series Figure 4 Attaching Support Brackets 4 With the help of a second in stalle r, insert the autolo ader into the rack so that the autoloader brackets slide into correspondin g support brackets on t he rear rails and the tabs at the front of the autoloader alig n flush with the clip nuts on the front ...
-
Quantum Audio 3A Series - page 10
10 Rack Mounting the Autoloader SuperLoader™ 3A Series Quick St art Guide Figure 5 Sliding Autoloader into Rack 5 While the other installer holds the front end of the autoloader, secure the front end of the autoloader to the rack us ing four ra ck screws (two per tab) as shown in figure 6 . Tighten the screws just enough to secure the autoloader ...
-
Quantum Audio 3A Series - page 11
Rack Mounting the Autoloader 11 SuperLoader 3A Series Figure 7 Connecting Support Brackets 7 Verify that the autoloader is level. Adjust as needed. 8 When the autoloader is level, tighte n all sc rews securing the autoloader to the rack. This includes the following: • Four screws securing the autolo ader tabs to the front rail s. • Four screws ...
-
Quantum Audio 3A Series - page 12
12 Autoloader Panel Overviews SuperLoader™ 3A Series Quick St art Guide Autoloader Panel Overviews The front panel allows you to configure th e autoloader, enter commands, and obtain status information. Figure 8 Front Panel Overview The Ethernet ports on the back panel allow you to conn ect to the A-Series tape drive FTP file server and to the au ...
-
Quantum Audio 3A Series - page 13
Connecting Ethernet and Powe r Cables 13 SuperLoader 3A Series Connecting Ethernet and Power Cables To connect the Ethernet and power cables to the autoloader, follow these steps: 1 Attach one end of the Ethernet cable (include d in the accessory kit) to the tape drive Ethernet port on the back panel of the autoloader. 2 Attach the other end of the ...
-
Quantum Audio 3A Series - page 14
Quantum Corp. (NYSE: QTM) is t he leading glob al storage company specializing in backup, recovery a nd archive. Combining focused expertise, custom er-driven innovation, and platform inde pendence, Quantum provides a comprehensiv e range of disk, tap e, media, and software solutions s upported by a world-clas s sales and servi ce organization. As ...
Quantum Audio 3A Seriesについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもQuantum Audio 3A Seriesの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQuantum Audio 3A Seriesで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。