Hobart ML-136135の取扱説明書

12ページ 1.16 mb
ダウンロード

ページに移動 of 12

Summary
  • Hobart ML-136135 - page 1

    N S T R U C T I O N S I 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 35219 (Oct. 2007) MODEL 3813 & 3913 SLICERS MODELS 3813 Manual Slicer ML-136135 3913 Automatic Slicer ML-136145 ...

  • Hobart ML-136135 - page 2

    – 2 – © HOBART CORPORATION 2007 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking . . . . . . . . ...

  • Hobart ML-136135 - page 3

    – 3 – Installation, Operation and Care of MODEL 3813 & 3913 SLICERS SA VE THESE INSTRUCTIONS GENERAL The model 3813 and 3913 slicers are equipped with a 1 ⁄ 2 HP motor and are available for single-phase electrical service. The slicer features the Hobart CleanCut TM 13" diameter contoured stainless steel knife. The slicer is furnished ...

  • Hobart ML-136135 - page 4

    – 4 – INST ALLA TION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installing the slicer, test the electrical service to assure it agrees with the specifications on the machine da ...

  • Hobart ML-136135 - page 5

    – 5 – ELECTRICAL This machine is provided with a three-prong grounding plug. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper grounding type, contact an electrician. CLEAN BEFORE USING The 3813 or 3913 slicer must be thoroughly cleaned and sanitized after installation and before being use ...

  • Hobart ML-136135 - page 6

    – 6 – TOP KNIFE COVER LA TCH KNOB PRODUCT TRA Y MEA T GRIP INDEX KNOB PRODUCT TRA Y HANDLE MEA T GRIP SLOT GAUGE PLA TE MEA T GRIP SLIDE ROD P ARK PIN CARRIAGE SLOT CONTROLS SIDE P ANEL OPERA TION Rotating knife. Use meat grip. Unplug machine power cord before cleaning, servicing or removing parts. Replace parts before use. SLICING — MODEL 38 ...

  • Hobart ML-136135 - page 7

    – 7 – SLICING — MODEL 3913 • Close the G AUGE P LATE by turning the I NDEX K NOB fully clockwise (Fig. 7). • Pull the P RODUCT T RAY (Fig. 7) all the way toward you until it reaches its stop (this is the home position). • Raise the M EAT G RIP to the top of the P RODUCT T RAY , and rest the P ARK P IN on the M EAT G RIP S LOT . • Plac ...

  • Hobart ML-136135 - page 8

    – 8 – CLEANING This machine must be thoroughly cleaned and sanitized at least as often as required by local regulation or after being idle for an extended period of time. The slicer knife is very sharp. Exercise extreme caution when working near the knife. Unplug the machine power cord and turn the index knob fully clockwise to close the gauge ...

  • Hobart ML-136135 - page 9

    – 9 – Clean completely around the R ING G UARD by working a moistened, folded paper towel between the R ING G UARD and the K NIFE (Fig. 15). Wash, rinse and sanitize both sides of the K NIFE by wiping outward from the center. Never clean any part of the slicer with steel pads. Carefully reassemble the plastic R ING G UARD C OVER by putting it i ...

  • Hobart ML-136135 - page 10

    – 10 – Fig. 19 Fig. 21 RIDGE ON KNIFE HUB (PLASTIC COVER REMOVED) PIN @ 1 O ’ CLOCK HOLE @ 11 O ’ CLOCK KNIFE REMOV AL TOOL PIN IN HOLE @ 11 O ’ CLOCK SLOTS AROUND 3 PINS Using the Knife Removal Tool Accessory Unplug the machine power cord and turn the index knob fully clockwise to close the gauge plate before cleaning the slicer. To Remo ...

  • Hobart ML-136135 - page 11

    – 11 – To Reinstall the Knife . . . • Orient the R IDGE on the K NIFE H UB so it points to the P IN on the R ING G UARD at the 1 o'clock position (Fig. 24). • Place the K NIFE and T OOL so the P IN on the K NIFE R EMOVAL T OOL is at the 11 o'clock position (Fig. 23). The S LOTS on the K NIFE R EMOVAL T OOL fit around the three P I ...

  • Hobart ML-136135 - page 12

    – 12 – FORM 35219 (Oct. 2007) MAINTENANCE Unplug the machine power cord and turn the index knob fully clockwise to close the gauge plate before doing any maintenance on the slicer. KNIFE SHARPENING The CleanCut TM K NIFE will provide long service in normal food retail or commercial kitchen use. Sharpen only when necessary; prolonged or too freq ...

メーカー Hobart カテゴリー Kitchen Utensil

Hobart ML-136135のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ML-136135の取扱説明書
- Hobartの製品カード
- パンフレット
- またはHobart ML-136135の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hobart ML-136135の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hobart ML-136135の取り付け説明書、サービスマニュアル、簡易説明書、またはHobart ML-136135のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hobart ML-136135の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hobart ML-136135デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHobart ML-136135を使用するのを助ける技術的文書のことです。説明書は通常、全てのHobart ML-136135ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hobartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hobart ML-136135の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHobart ML-136135の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hobart ML-136135に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hobart ML-136135デバイスの基本機能を使うにあたってのヒント。 Hobart ML-136135のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hobart ML-136135に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHobart ML-136135のメーカー/サービスへの連絡先に関する情報。

Hobart ML-136135についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHobart ML-136135の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart ML-136135で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)